HORACO ZX510P-7T1XS-280

Contents

HORACO 10Gb Managed POE Switch ZX510P-7T1XS-280 User Manual

Model: ZX510P-7T1XS-280 | Brand: HORACO

1. Introduction

This manual provides detailed instructions for the installation, configuration, operation, and maintenance of the HORACO ZX510P-7T1XS-280 10Gb Managed PoE Switch. It is designed for network installers and system administrators.

1.1 Target Audience

This manual is intended for installers and system administrators responsible for network installation, configuration, and maintenance. Users should have a basic understanding of network communication, management protocols, and technical terms related to networking. Familiarity with Graphical User Interface (GUI), Command-line Interface, Simple Network Management Protocol (SNMP), and Web Explorer is also beneficial.

1.2 Manual Convention

Throughout this manual, specific conventions are used to highlight important information:

  • Interpretation: Describes operations and provides necessary information.
  • Caution: Reminds the user of potential risks. Improper operations may result in data loss or equipment damage.

2. Safety Information

Please read and understand all safety instructions before installing or operating the device. Failure to do so may result in injury, damage to the device, or property damage.

  • Ensure the power supply voltage matches the device's requirements (AC 100-240V 50/60Hz).
  • Do not open the device casing. There are no user-serviceable parts inside.
  • Keep the device away from water, fire, and high humidity environments.
  • Ensure proper ventilation to prevent overheating. The device features dual-fan cooling, but adequate airflow is still necessary.
  • Use only approved cables and accessories.
  • Disconnect power before cleaning or performing any maintenance.

3. Package Contents

Verify that all items are present in the package:

  • 1x HORACO 10Gb Managed POE Switch (ZX510P-7T1XS-280)
  • 1x Power cord
  • 1x User Manual (this document)
  • 1x Certificate of Conformity
  • 1x Pair of Rack Ears
Product parameters table and packing list
Figure 1: Product Parameters and Packing List

4. Product Overview

The HORACO ZX510P-7T1XS-280 is a 10Gb Web Managed PoE Switch designed for high-performance networking. It features 7x 10Gbps PoE RJ45 ports and 1x 10Gbps SFP+ optical uplink port.

4.1 Physical Description and Dimensions

Dimensions of the switch: 320mm (width), 222mm (depth), 45mm (height)
Figure 2: Switch Dimensions

The switch has a compact design suitable for rack mounting. Its dimensions are approximately 320mm (Width) x 222mm (Depth) x 45mm (Height).

4.2 Port Layout and Indicators

Front view of the HORACO 10Gb Web Managed PoE Switch, highlighting 7x 10Gbps PoE ports and 1x 10Gbps SFP+ uplink
Figure 3: Front Panel Overview
Close-up of the switch ports, indicating 240W PoE power output and 1-7 ports supporting 802.3af/at/bt with 90W per port
Figure 4: PoE Port Details

The front panel includes:

  • 7x 10Gbps PoE RJ45 Ports (Ports 1-7): These ports support 802.3af/at/bt standards, with a maximum output of 90W per port and a total PoE power budget of 240W.
  • 1x 10Gbps SFP+ Optical Port (Port 8): Used for high-speed fiber optic uplink connections.
  • LED Indicators:
    • PWR (Green Light): Bright indicates power is on.
    • SYS (Green Light): Bright indicates the system is working; Blinking indicates system startup in progress.
    • Link/Act (Green/Yellow): Green light indicates 10G rate; Yellow light indicates 1G/2.5G/5G rate; Not bright indicates no link; Blinking indicates data transfer.
  • Reset Button: Used to reset the device.

5. Specifications

Detailed technical specifications for the HORACO ZX510P-7T1XS-280 switch:

Detailed product parameter table including port definitions, voltage, network protocols, performance, installation, lightning protection, and PoE parameters
Figure 5: Product Parameter Table
AttributeValue
Product Name8 Port 10GbE Web Managed PoE Switch
Model NumberZX510P-7T1XS-280
Brand NameHORACO
Switch TypeEthernet
Number of Interfaces7*10Gbps POE RJ45 ports, 1*10Gbps SFP+ port
Transmission Rate2000 Mbps
Switch Capacity160Gbps
Packet Forwarding Rate119.04Mpps
MAC Address Table Size16K
Jumbo Frame10K
Communication ModeFull-Duplex & Half-Duplex
Network ProtocolIEEE802.3 (Ethernet), IEEE802.3u (Fast Ethernet), IEEE802.3ab (Gigabit Ethernet), IEEE 802.3bz (5G Ethernet), IEEE 802.3z (Gigabit Ethernet), IEEE 802.3ae (10G Ethernet), IEEE802.3x (Flow Control)
Network Medium10Base-T: Cat3, 4, 5 or above UTP/STP(≤100m); 100Base-TX: Cat5 or above UTP/STP(≤100m); 1000Base-TX: Cat5 or above UTP/STP(≤100m); 2.5GBase-T: Cat5 or above UTP/STP(≤100m); 5GBase-T: Cat6 or above UTP/STP(≤100m); 10GBase-T: Cat6 or above UTP/STP(≤100m)
Power VoltageAC 100-240V 50/60Hz
PoE Power OutputPorts 1-7 (PoE power output <90W)
Working EnvironmentTemperature: 0-40°C; Humidity: 10%-90% (non-condensing)
Storage EnvironmentTemperature: -40-70°C; Humidity: 5%-95% (non-condensing)
Installation MethodRackmount, Desktop
Lightning ProtectionCommon Mode 4KV, Differential Mode 1KV, ESD: Contact 6KV, Air 8KV
CertificationCE, FCC, RoHS

6. Setup and Installation

6.1 Rack Mounting

The switch is designed for standard 1U rack mounting. Use the provided rack ears to secure the device in a server cabinet.

The switch mounted in a standard 1U rack, showing included rack ears
Figure 6: Standard 1U Rack Mount
Standard 1U rack mount design, showing compact installation
Figure 7: Rack Installation Example

6.2 Connecting Devices

Connect your network devices (e.g., IP cameras, access points, computers, NAS) to the RJ45 PoE ports (1-7) using appropriate Ethernet cables (Cat5e/6/7). For high-speed uplinks, use the SFP+ port (8) with compatible fiber optic modules or DAC cables (modules not included).

The switch connected to multiple devices like NAS, laptop, camera, router, and printer
Figure 8: Compatible with Multiple Devices
Illustration of plug-and-play functionality with various SFP modules (modules not included)
Figure 9: Plug and Play Connectivity

6.3 Power Connection

Connect the provided power cord to the switch's power input and then to a suitable AC power outlet (100-240V, 50/60Hz). The PWR LED will illuminate when power is supplied.

7. Web Management Interface

The switch features a web-based management interface for easy configuration and monitoring.

Screenshot of the web management interface for VLAN Port Setting and Link Aggregation (LACP)
Figure 10: Web Management Overview

7.1 Logging In

  1. Connect your computer to any of the switch's RJ45 ports.
  2. Configure your computer's IP address to be in the same network segment as the switch, but with a different IP address. For example, set your PC's IP to 192.168.2.x (where 1 < x ≤ 254) and subnet mask to 255.255.255.0.
  3. Open a web browser (recommended: IE 9.0+, Chrome 23.0+, Firefox 20.0+).
  4. Type the default switch IP address http://192.168.2.1 into the address bar and press Enter.
  5. A login window will appear. Enter the default username admin and password admin.
  6. Click "Login" to access the switch system.

7.2 Client Interface and Navigation

The web interface provides a navigation bar with various menu items, each containing submenus for detailed configuration. Key menu items include Status, Network, Port, VLAN, MAC Address Table, Spanning Tree, ERPS, Multicast, Security, QoS, Diagnostics, and Management.

8. Configuration and Operation

8.1 Status

This section provides an overview of the switch's current operational status.

  • System Information: Displays product info, device states, and function on/off states. Navigate to Status > System Information.
  • Port Statistics: Shows detailed flow statistics for each port. Access via Status > Port > Statistics.
  • MAC Address Table: View the MAC address table of the device. Found under Status > MAC Address Table.
  • Reboot: Allows you to reboot the switch. Click Reboot in the upper right corner of the interface.

8.2 Network Settings

Configure the basic network parameters of the switch.

  • IP Address: Change the management IP address. Navigate to Network > IP Address.
  • DNS: Configure DNS server settings. Access via Network > DNS.
  • System Time: Set the system time and time source. Found under Network > System Time.

8.3 Port Configuration

Manage individual port settings and advanced features.

  • Port Setting: Configure all ports, including speed, duplex, and flow control. Navigate to Port > Port Setting.
  • Link Aggregation (LAG): Bundle multiple physical interfaces into a single logical interface for increased bandwidth and reliability. Access via Port > Link Aggregation.
  • Diagram illustrating Link Aggregation for increased bandwidth and redundancy across network layers
    Figure 11: Link Aggregation Concept
  • EEE (Energy Efficient Ethernet): Configure EEE settings to reduce power consumption. Found under Port > EEE.
  • Jumbo Frame: Set the Maximum Transmission Unit (MTU) for ports. Navigate to Port > Jumbo Frame.
  • Port Security: Prevent unauthorized devices from accessing the network by limiting MAC addresses per port. Access via Port > Port Security.
  • Protected Port: Isolate ports to prevent direct communication between them, useful for broadcast/multicast storm control. Found under Port > Protected Port.
  • Storm Control: Configure policing rates for broadcast, unknown multicast, and unicast storms. Navigate to Port > Storm Control.
  • Mirroring: Copy traffic from a source port to a destination port for monitoring. Access via Port > Mirroring.

8.4 PoE Settings

Manage Power over Ethernet (PoE) functionality for connected devices.

  • PoE Port Setting: Configure individual PoE port settings, including power enable/disable and watchdog function. Navigate to PoE Setting > PoE Port Setting.
Screenshot of the PoE Port Management interface, showing real-time power consumption
Figure 12: PoE Port Management

8.5 VLAN Configuration

Configure Virtual Local Area Networks (VLANs) to segment your network.

  • VLAN: Overview of VLAN functionality.
  • Create VLAN: Create new VLANs. Navigate to VLAN > VLAN > Create VLAN.
  • VLAN Configuration: Add ports to VLANs. Access via VLAN > VLAN > VLAN Configuration.
  • Membership: Configure port membership in VLANs. Found under VLAN > VLAN > Membership.
  • Port Setting: Configure VLAN attributes for trunk interfaces. Navigate to VLAN > VLAN > Port Setting.

8.6 MAC Address Table

Manage MAC address entries for efficient data forwarding.

  • Static Address: Manually configure static MAC address entries. Navigate to MAC Address Table > Static Address.
  • Filtering Address: Configure MAC addresses to be filtered/discarded. Access via MAC Address Table > Filtering Address.

8.7 Spanning Tree

Configure Spanning Tree Protocol (STP) to prevent network loops and ensure redundancy.

  • Property: Configure global STP parameters. Navigate to Spanning Tree > Property.
  • Port Setting: Adjust STP parameters for individual ports. Access via Spanning Tree > Port Setting.
  • MST Instance: Configure Multiple Spanning Tree (MST) instances. Found under Spanning Tree > MST Instance.
  • MST Port Setting: Configure MST parameters for specific ports. Navigate to Spanning Tree > MST Port Setting.
  • Statistics: View STP port statistics. Access via Spanning Tree > Statistics.

8.8 ERPS (Ethernet Ring Protection Switching)

Configure ERPS for high reliability and stability in ring networks.

  • Property: Enable/disable global ERPS function. Navigate to ERPS > Property.
  • ERPS Instance: Create and configure ERPS instances. Access via ERPS > ERPS Instance.

8.9 Loopback

Configure Loopback Detection to prevent network loops.

  • Loopback Config: Enable and configure loopback detection settings. Navigate to Loopback > Loopback Config.

8.10 Discovery (LLDP)

Configure Link Layer Discovery Protocol (LLDP) for network device discovery.

  • LLDP Property: Enable/disable LLDP and configure TLV advertisement. Navigate to Discovery > LLDP > Property.
  • LLDP Port Setting: Configure LLDP mode for individual ports. Access via Discovery > LLDP > Port Setting.
  • MED Network Policy: Configure LLDP-MED network policies. Found under Discovery > LLDP > MED Network Policy.
  • MED Port Setting: Configure LLDP-MED settings for ports. Navigate to Discovery > LLDP > MED Port Setting.
  • Packet View: View LLDP packet information. Access via Discovery > LLDP > Packet View.
  • Local Information: View local device summary and port status. Found under Discovery > LLDP > Local Information.
  • Neighbor: Display LLDP neighbor information. Navigate to Discovery > LLDP > Neighbor.

8.11 Multicast

Configure multicast settings for efficient delivery of data to multiple recipients.

  • General Property: Configure general multicast function settings. Navigate to Multicast > General > Property.
  • Group Address: Add static multicast group addresses. Access via Multicast > Group Address.
  • Router Port: Configure and view multicast router ports. Found under Multicast > General > Router Port.
  • IGMP Snooping: Configure IGMP Snooping to manage and control multicast groups. Navigate to Multicast > IGMP Snooping.

8.12 Security

Enhance network security through various access and snooping configurations.

  • Management Access: Configure HTTP/SNMP management service access. Navigate to Security > Management Access > Management Service.
  • DHCP Snooping: Enable DHCP Snooping to prevent unauthorized DHCP servers and record user IP/MAC addresses. Access via Security > DHCP Snooping.
  • IMPV Binding: Configure IP-MAC-Port-VLAN binding for enhanced security. Found under Security > IP Source Guard > IMPV Binding.

8.13 QoS (Quality of Service)

Prioritize network traffic to ensure optimal performance for critical applications.

Diagram showing QoS policy implementation in a network environment for different data types
Figure 13: Perfect QoS Policy
  • General Property: Configure global QoS function and trust mode. Navigate to QoS > General > Property.
  • Queue Scheduling: Configure queue scheduling algorithms (Strict-Priority, WRR). Access via QoS > General > Queue Scheduling.
  • CoS Mapping: Map Class of Service (CoS) values to queues. Found under QoS > General > CoS Mapping.
  • DSCP Mapping: Map Differentiated Services Code Point (DSCP) values to queues. Navigate to QoS > General > DSCP Mapping.
  • Rate Limit: Configure ingress/egress port rate limiting. Access via QoS > Rate Limit > Ingress / Egress Port.

9. Diagnostics

Use diagnostic tools to test network connectivity and cable integrity.

  • Ping: Check the availability of specified IP addresses or hostnames. Navigate to Diagnostics > Ping.
  • Copper Test: Evaluate the state of copper cables and locate faults. Access via Diagnostics > Copper Test.
  • Fiber Module: View DDM (Digital Diagnostic Monitoring) information for optical modules. Found under Diagnostics > Fiber Module.

10. Maintenance

Perform routine maintenance tasks to ensure optimal device performance and security.

10.1 User Account Management

Manage user accounts for accessing the switch's management interface.

  • User Account: Check and modify usernames, passwords, and privileges. Navigate to Management > User Account.

10.2 Firmware Upgrade

Update the switch's firmware to gain new features and improve stability.

  • Manual Upgrade: Perform a manual firmware upgrade. Navigate to Management > Firmware > Manual Upgrade.

10.3 Configuration Management

Save and restore switch configurations.

  • Manual Upgrade (Configuration): Upgrade configuration files. Navigate to Management > Configuration > Manual Upgrade.
  • Save Configuration: Save the current running configuration or restore to factory defaults. Access via Management > Configuration > Save Configuration.

10.4 SNMP (Simple Network Management Protocol)

Configure SNMP for network management and monitoring.

  • View: Configure SNMP views. Navigate to Management > SNMP > View.
  • Group: Configure SNMP groups. Access via Management > SNMP > Group.
  • Community: Configure SNMP communities. Found under Management > SNMP > Community.
  • User: Configure SNMP users. Navigate to Management > SNMP > User.
  • Engine ID: Configure SNMP engine IDs. Access via Management > SNMP > Engine ID.
  • Trap Event: Configure SNMP trap events. Found under Management > SNMP > Trap Event.
  • Notification: Configure SNMP notifications. Navigate to Management > SNMP > Notification.

11. Troubleshooting

This section provides general guidance for common issues. For more specific problems, refer to the detailed configuration sections or contact technical support.

  • No Power: Ensure the power cord is securely connected and the power outlet is functional. Check the PWR LED.
  • No Link on Port: Verify the Ethernet cable connection, check the cable integrity (using Copper Test in Diagnostics), and ensure the connected device is powered on and functioning. Check the Link/Act LED.
  • Cannot Access Web Interface: Confirm your PC's IP address is in the same subnet as the switch (default 192.168.2.x). Try pinging the switch's default IP (192.168.2.1). Clear browser cache or try a different browser.
  • PoE Device Not Powering On: Ensure the device is PoE compatible (802.3af/at/bt) and within the power budget of the port (<90W) and total switch (240W). Check PoE Port Settings in the web interface.
  • Network Performance Issues: Check port statistics for errors or high utilization. Review QoS settings, Link Aggregation status, and ensure no network loops are present (Spanning Tree, Loopback).

12. User Tips

  • Regularly Update Firmware: Keep your switch's firmware up-to-date to benefit from performance improvements, new features, and security patches.
  • Backup Configuration: Always save a backup of your switch configuration after making significant changes. This allows for quick restoration in case of misconfiguration or device replacement.
  • Monitor Port Statistics: Periodically check port statistics for errors or unusual traffic patterns to proactively identify and resolve network issues.
  • Utilize VLANs for Segmentation: For improved security and network performance, segment your network using VLANs, especially when connecting different types of devices or departments.
  • Leverage PoE Management: Use the PoE Port Management feature to monitor power consumption and enable/disable PoE on specific ports as needed, which can help with power budgeting and troubleshooting.

13. Warranty and Support

13.1 Warranty

The HORACO 10Gb Managed POE Switch ZX510P-7T1XS-280 comes with a 1-Year Free Warranty from the date of purchase, covering manufacturing defects and malfunctions under normal use.

13.2 Technical Support

HORACO provides Lifetime Professional Technical Support for this product. If you encounter any issues or have questions regarding installation, configuration, or troubleshooting, please contact HORACO Official Store support channels.

13.3 Additional Resources

For further detailed information and advanced configurations, you may refer to the official user manual PDF available for download. The PDF manual provides in-depth explanations and screenshots for each web management feature.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.