VEKOOTO 8-inch Video Fish Finder

Contents

VEKOOTO 8-inch HD 1080P DVR Fish Finder

Model: 8-inch Video Fish Finder

Brand: VEKOOTO

1. Introduction

The VEKOOTO 8-inch HD 1080P DVR Fish Finder is an advanced underwater camera system designed to enhance your fishing experience. Featuring an 8-inch high-definition display, a 1080P camera with night vision capabilities, and recording functionality, this device allows you to observe underwater environments clearly. It is suitable for various fishing scenarios, including ice fishing, sea fishing, and river fishing.

2. Package Contents

Please check the package carefully to ensure all items are present:

Package contents of VEKOOTO 8-inch Fish Finder

Image: Contents of the VEKOOTO Fish Finder package.

  • 1 x 8-inch Monitor
  • 1 x 1080P Camera
  • 1 x 20-meter Camera Cable
  • 1 x Tripod
  • 1 x Toolbox (Carrying Case)
  • 1 x Charger

3. Setup

3.1 Initial Charging

To extend the monitor's lifespan, please charge the battery promptly when it is low. When charging, ensure the monitor is turned off. Use the provided charger with a 5V voltage and 2A current output.

3.2 Connecting the Camera

With the device powered off, carefully insert the camera plug into the video jack on the side of the monitor. Ensure a secure connection. Then, power on the display to view the camera feed.

3.3 Attaching the Tripod

Align the tripod mount with the corresponding slot on the monitor. Align the tripod screw plug with the nut opening and turn clockwise until securely tightened.

3.4 Inserting an SD Card

Locate the SD Card Slot on the side of the monitor (refer to Product Analysis diagram). Gently insert a compatible SD card until it clicks into place. This is required for recording photos and videos.

Product analysis diagram showing ports and buttons

Image: Product Analysis showing monitor ports (Video Cable Port, SD Card Slot, USB Type-C Charging Port) and buttons.

4. Operating Instructions

4.1 Power On/Off

  • To Power On: Press the power button down. The indicator light will turn red, signifying the camera is on.
  • To Power Off: Press the power button up. The screen will turn black, indicating the camera is off.

4.2 Night Vision Function

  • To Activate: Turn the infrared switch down. A green light circle will appear in the upper left corner of the display screen, indicating that the camera's infrared night vision light is on.
  • To Deactivate: Turn the infrared switch up. The green light circle will disappear from the upper left corner of the display screen, indicating that the infrared night vision light has been turned off.

4.3 Menu Navigation and Functions

Press the 'M' (Menu) button repeatedly to cycle through different functions. Once the desired function is highlighted, press 'OK' to enter or confirm the selection. Use the '+' and '-' buttons to adjust settings within a function.

Menu Function Description
FunctionDescription
Loop recording timeAdjust the loop recording duration. Select, then press 'OK' and '+/-' to operate.
Motion detection sensitivityAdjust the sensitivity of the motion detection alarm. Select, then press 'OK' and '+/-' to proceed.
Recording with tabAdjust the audio recording settings. Select, then press 'OK' and '+/-' to operate.
VolumeAdjust the system volume. Select, then press 'OK' and '+/-' to operate.
Clock settingsAdjust the display time. Select, then press 'OK' and '+/-' to perform the operation.
LanguagePress 'OK' and '+/-' to switch languages.
Lens voltageAdjust the voltage from 12V to 20V as needed. Press 'OK' and '+/-' to operate.
LCD contrastAdjust the LCD contrast. Select, then press 'OK' and '+/-' to perform the operation.
Screen backlightAdjust the screen brightness. Select, then press 'OK' and '+/-' to perform the operation.
LCD BrightnessAdjust the LCD brightness. Select, then press 'OK' and '+/-' to perform the operation.
LCD SaturationAdjust the LCD saturation. Select, then press 'OK' and '+/-' to perform the operation.
Format SD cardFormat the inserted SD card. Select, then press 'OK' and '+/-' to perform the operation.
System resetRestore factory settings. Select, then press 'OK' and '+/-' to perform the operation.

4.4 Display Adjustment Functions

These functions allow fine-tuning of the display image quality:

  • Backlight: Adjust the screen brightness.
  • Brightness: Adjust the overall image brightness.
  • Contrast: Adjust the image contrast.
  • Gamma: Adjust the image clarity.
  • Pattern: Adjust the image contrast.
  • Voltage Regulation: Adjust the voltage (12V-24V) for the camera.
  • Full Wire Line: Adjust this function as needed.

5. Maintenance

5.1 General Precautions

  • Avoid collisions and do not disassemble the machine without authorization to prevent damage to its waterproof performance.
  • Do not leave the monitor in a car for extended periods, and do not expose it to temperatures exceeding 50 degrees Celsius (122°F).
  • Clean the screen and camera lens with a soft, dry cloth. Avoid using abrasive cleaners.

5.2 Water Ingress

  • Serious Screen Water Ingress: If water enters the inner screen, immediately shut down the device and do not turn it on. Allow it to dry thoroughly before attempting to turn it on again. If it still cannot be turned on after drying, contact customer service for assistance.
  • Watermarks: If water splashes into the inner screen, visible watermarks may appear. The device can still be used normally. For complete removal of watermarks, contact customer service for internal screen replacement.

5.3 Battery Care

Always charge the battery when it is low to maintain its lifespan. Store the device in a cool, dry place when not in use for extended periods.

6. Troubleshooting

Below are common issues and their potential solutions:

Common Troubleshooting Methods
ProblemSolution
Blue ScreenCaused by loose camera connection or damaged video cable. Tighten the camera connection, adjust voltage via 'M' button to 24 volts. If issue persists, contact customer service.
Black ScreenFirst, rule out water ingress. If not, check power. Try charging. If it still doesn't turn on, contact customer service. If no response after pressing 'M' button at startup, unplug and re-plug the camera.
Watermark on ScreenIf water splashes into the inner screen, watermarks may appear. The device can still be used normally. For complete removal, contact customer service for internal screen replacement.

7. Specifications

Product specifications table and included accessories

Image: Product Specifications and Included Accessories.

Product Specifications
FeatureDetail
Product Name8-inch Video Fish Finder
BrandVEKOOTO (Neutral)
Display Resolution1920*1080 (Full HD)
Display Size8-inch (21.2 cm diagonal)
Internal Screen Brightness2000 cd/m²
CameraSony 1080P
Camera Angle220 Degrees
Camera Light Source8 Infrared LED lights (not visible to human eye)
Camera Casing MaterialSpace aluminum (corrosion-resistant)
LensFully waterproof lens
Video Cable20 meters, Four-copper core, 12mm diameter, special detection signal wire
Display Output Voltage12V-24V (adjustable)
Battery Capacity10000mAh
Battery LifeApprox. 6-12 hours (continuous use)
Charging TimeApprox. 10 hours
Operating Temperature-20°C to +60°C (-4°F to 140°F)
Total Weight1388 g
Product Dimensions21.2 x 14.5 x 2.6 cm
Aluminum Case Dimensions25.8 x 16.5 x 9.6 cm

8. User Tips

  • Charger Compatibility: Ensure the provided charger is compatible with your local power outlets (e.g., EU plug for Europe, US plug for North America). An adapter may be needed.
  • Manual Translation: If the included user manual is in a foreign language, consider using a smartphone translation app to assist with understanding the instructions.
  • Camera Housing: Note that some product variations may feature a plastic camera housing instead of metal. Verify product details if the material type is a specific concern for your use case.
  • Water Quality Adjustment: For optimal viewing, adjust the display's color settings (green, red, blue values) according to the water quality (clear, muddy) as described in the manual's precautions.

9. Warranty and Support

Product quality issues that occur during normal use are typically covered by a free warranty. This warranty generally covers manufacturing defects. However, damage caused by human factors, such as screen water ingress, screen breakage, or camera hanging/damage, may not be covered under the free warranty, and replacement parts may be charged.

For any issues, technical support, or warranty claims, please contact the seller or the store where you purchased the product. Provide your order details and a clear description of the problem for efficient assistance.

© 2023 VEKOOTO. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.