BAOFENG UV-5R / UV-5R Mini

Contents

Baofeng UV-5R / UV-5R Mini Walkie Talkie User Manual

Professional FM Transceiver

1. Introduction

Thank you for purchasing our Baofeng UV-5R / UV-5R Mini Amateur Portable Radio. This dual-band/dual-display radio is designed to provide secure, instant, and reliable communications at peak efficiency. Please read this manual carefully before use to ensure maximum performance from your radio.

This manual covers both the UV-5R and UV-5R Mini models, highlighting their shared features and distinct characteristics.

2. Safety Information

The following safety precautions must always be observed during operation, service, and repair of this equipment:

  • This equipment should be serviced by qualified technicians only.
  • Do not modify the radio for any reason.
  • Use only supplied or approved batteries and chargers.
  • Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result.
  • Turn off your radio prior to entering any area with explosive and flammable materials.
  • Do not charge your battery in a location with explosive and flammable materials.
  • To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any area where posted notices instruct you to do so.
  • Turn off your radio before boarding an aircraft. Any use of a radio must be in accordance with airline regulations or crew instructions.
  • Turn off your radio before entering a blasting area.
  • For vehicles with an air bag, do not place a radio in the area over an air bag or in the air bag deployment area.
  • Do not expose the radio to direct sunlight for a long time, nor place it close to a heating source.
  • When transmitting with a portable radio, hold the radio in a vertical position with the microphone 3 to 4 centimeters away from your lips.
  • Keep the antenna at least 2.5 centimeters away from your body when transmitting.

WARNING: If you wear a radio on your body, ensure the radio and its antenna are at least 2.5 centimeters away from your body when transmitting.

3. Features and Functions

The Baofeng UV-5R and UV-5R Mini models offer a range of features designed for versatile communication:

Common Features (UV-5R & UV-5R Mini):

  • Dual-band handheld transceiver with display function menu on the LCD.
  • DTMF encoded.
  • Lithium-ion battery with high capacity.
  • Commercial FM radio receiver (65 MHz ~ 108 MHz).
  • Incorporates 105 DCS codes and 50 CTCSS privacy codes, programmable.
  • VOX (Voice Operated Transmission) function.
  • Alarm function.
  • Up to 128 memory channels.
  • Broadband (Wide) / Narrowband (Narrow) selectable.
  • High power / low power selectable (UV-5R: 5W/1W; UV-5R Mini: 5W/2W).
  • Display illumination and programmable keyboard.
  • Function 'beep' on the keyboard.
  • Dual Watch / dual reception.
  • Selectable Frequency Step: 2.5/5/6.25/10/12.5/25 kHz.
  • Function 'OFFSET' (frequency offset for repeater access).
  • Battery saving function 'SAVE'.
  • Timer transmission 'TOT' programmable.
  • Scan Mode selection.
  • Function Busy Channel Lock 'BCLO'.
  • Built-in RX CTCSS/DCS scan.
  • Built-in LED flashlight.
  • Programmable by PC.
  • Level Threshold 'Squelch' adjustable from 0 to 9.
  • Crossband reception.
  • Tone end of transmission.
  • Built-in key lock.

UV-5R Mini Specific Features:

  • 1.44 inch TFT Color Display Screen.
  • One-key fast Channel Copy.
  • APP Wireless Programming.
  • Mini Compact size.
  • Dual-PTT Switches Design.
  • 1000Hz/1450/1750/2100Hz alert.
  • Built-in HI-FI Speaker 16Ω 1W.
  • 10 NOAA Weather Forecast Channels.
  • Direct Type-C cable charging port on the battery.
  • 1600mAh ultra-high battery power capacity for longer working time.
  • High-illumination Flashlight.
  • Roger Beep.
  • SOS Alarm.
  • Manual Programming.
Comparison of Baofeng UV-5R and UV-5R Mini walkie talkies, showing their different displays and sizes.
Figure 1: Comparison of UV-5R and UV-5R Mini models.
Baofeng UV-5R showing features like FM radio, VOX, flashlight, alarm, fall prevention, encryption, and long standby.
Figure 2: Key features of the Baofeng UV-5R.
Baofeng UV-5R Mini held in a hand, demonstrating its compact size.
Figure 3: The compact size of the UV-5R Mini.
Baofeng UV-5R Mini with its 1.44 inch TFT color display and dual PTT buttons highlighted.
Figure 4: UV-5R Mini 1.44 inch TFT Color Display and Dual PTT.
Baofeng UV-5R Mini showing its Type-C charging port on the battery.
Figure 5: UV-5R Mini Type-C Charging.

4. Unpacking and Checking Equipment

Carefully unpack your transceiver. We recommend that you identify the items listed below before discarding the packing material. If any items are missing or have been damaged during shipment, please contact your dealer immediately.

Standard Package Contents:

  • Portable UV-5R / UV-5R Mini Radio Body
  • Battery
  • Antenna
  • Desk charger
  • Charger adapter
  • Belt clip
  • Lanyard (Sling)
  • User's manual
  • 771 Antenna (may vary by package)
  • USB-C Charging Cable (UV-5R Mini)
Diagram showing the standard package contents of the Baofeng UV-5R walkie talkie, including the radio, battery, antenna, charger, adapter, belt clip, and micro-headset.
Figure 6: Standard package contents.

Note: Items included in the package may differ from those listed above depending on the country of purchase. For more information, consult your dealer or vendor.

5. Installation of Accessories

5.1. Installing the Antenna

Install the antenna as shown in the figure below and turn it clockwise until it stops.

Diagram showing how to install the antenna on the walkie talkie.
Figure 7: Antenna installation.

Note:

  • When installing the antenna, do not rotate it by its top; hold it by its base and turn.
  • If you use an external antenna, make sure the 'SWR' (Standing Wave Ratio) is about 1.5:1 or less, to avoid damage to the transceiver's final transistors.
  • Do not hold the antenna with your hand or wrap the outside of it to avoid bad operation of the transceiver.
  • Never transmit without an antenna.

5.2. Installing the Belt Clip

If necessary, install the belt clip at the rear of the battery compartment cover as shown in the figure below.

Diagram showing how to install the belt clip on the walkie talkie.
Figure 8: Belt clip installation.

Note: Do not use any kind of glue to fix the screw on the belt clip. Solvents in glue may damage the battery casing.

5.3. Micro-Headset Installation of External

Plug the external micro-headset connector into the jack of 'SP. & MIC' of the transceiver as shown in the figure below.

Diagram showing where to plug in the micro-headset on the walkie talkie.
Figure 9: Micro-headset connection point.

6. Battery Information and Charging

5.4. Battery Installation

When attaching the battery, make sure it is parallel and in good contact with the aluminum chassis. The battery bottom should be about 1 to 2 centimeters below the bottom of the radio's body. Align the battery with the guide rails on the aluminum chassis and slide it upwards until a 'click' is heard. The battery latch at the bottom locks the battery.

To remove the battery, turn off the radio. Slide the battery latch at the bottom of the radio's body in the direction indicated by the arrow. Slide down the battery for about 1 to 2 centimeters, and then remove the battery from the radio's body.

6. Battery Charging

Use only the charger specified by the manufacturer. The charger's LED indicates the charging progress.

Diagram showing the walkie talkie being charged in its charging cradle.
Figure 10: Charging the walkie talkie.

Charging Steps:

  1. Plug the power cord into the adapter.
  2. Plug the AC connector of the adapter into the AC outlet socket.
  3. Plug the DC connector of the adapter into the DC socket on the back of the charger.
  4. Place the radio with the battery attached, or the battery alone, in the charger.
  5. Make sure the battery is in good contact with the charging terminals. The charging process initiates when the red LED lights.
  6. The green LED lights about 4 hours later, indicating the battery is fully charged. Then remove the radio with the battery attached or the battery alone from the charger.

7.1. Initial Use

New batteries are shipped uncharged fully from the factory. Charge a new battery for 5 hours before initial use. Maximum battery capacity and performance are achieved after three full charge/discharge cycles. If you notice the battery power runs low, please recharge the battery.

WARNING:

  • To reduce the risk of injury, charge only the battery specified by the manufacturer. Other batteries may burst, causing bodily injury and property damage.
  • To avoid risk of personal injury, do not dispose of batteries in a fire!
  • Dispose of batteries according to local regulations (e.g., recycling). Do not dispose as household waste.
  • Never attempt to disassemble the battery.

7.2. Battery Tips

  1. When charging your battery, keep it at a temperature among 5°C - 40°C. Temperatures outside this limit may cause battery leakage or damage.
  2. When charging a battery attached to a radio, turn the radio off to ensure a full charge.
  3. Do not cut off the power supply or remove the battery when charging.
  4. Never charge a battery that is wet. Please dry it with a soft cloth prior to charging.
  5. The battery will eventually wear out. When the operating time (talk-time and standby time) is noticeably shorter than normal performance, it is time to buy a new battery.

7.3. Prolong Battery Life

  1. Battery performance will be greatly decreased at a temperature below 0°C. A spare battery is necessary in cold weather. A cold battery unable to work in this situation may work under room temperature, so keep it for later use.
  2. Dust on the battery contact may cause the battery to not work or charge. Please use a clean dry cloth to wipe it before attaching the battery to the radio.

7.4. Battery Storage

  1. Fully charge a battery before you store it for a long time, to avoid battery damage due to over-discharge.
  2. Recharge a battery after several months' storage (Li-Ion batteries: 6 months), to avoid battery capacity reduction due to over-discharge.
  3. Store your battery in a cool and dry place under room temperature, to reduce self-discharge.

7. Parts, Controls and Keys

8.1. Radio Overview

Diagram showing the different parts of the Baofeng UV-5R Mini walkie talkie, including antenna, flashlight, knob, LCD, side keys, PTT, VFO/MR, LED indicator, strap buckle, accessory jack, A/B key, BAND key, keypad, SP.&MIC., battery pack, battery contacts, and battery remove button.
Figure 11: UV-5R Mini Radio Overview.

The radio consists of the following main parts:

  1. Antenna
  2. Flashlight
  3. Knob (ON/OFF, Volume)
  4. LCD
  5. SK-side key1/CALL (Radio, Alarm)
  6. SK-side key2/MONI (Flashlight, Monitor)
  7. PTT key (Push-to-Talk)
  8. VFO/MR (Frequency mode/Channel mode)
  9. LED indicator
  10. Strap buckle
  11. Accessory jack
  12. A/B key (Frequency display switches)
  13. BAND key (Band switches)
  14. Keypad
  15. SP. & MIC.
  16. Battery pack
  17. Battery contacts
  18. Battery remove button

8.2. Command/Key Definition

  • [PTT] (PUSH-TO-TALK): Press and hold down the [PTT] button to transmit; release it to receive.
  • SK-SIDE KEY1/[CALL]: Press the [CALL] button to activate the FM Radio; press it again to deactivate the FM Radio. Press and hold on the [CALL] button to activate the alarm function; press and hold it again to deactivate the alarm function.
  • SK-SIDE KEY2/[MONI]: Press the [MONI] button to turn on the flashlight; press it again to turn off. Press and hold on the [MONI] button to monitor the signal.
  • [VFO/MR] BUTTON: Press the [VFO/MR] button to switch between frequency mode and channel mode.
  • [A/B] BUTTON: Press the [A/B] button to switch frequency display.
  • [BAND] BUTTON: Press the [BAND] button to switch band display. While FM radio is active, press the [BAND] button to switch the band of FM radio (band 65-75MHz/76-108MHz).
  • [*SCAN] KEY: Press the [*SCAN] key to activate the Reverse function, which exchanges a separate reception and transmission frequency. Press the [*SCAN] key for 2 seconds to start scanning (frequency/channel). While FM radio is active, press the [*SCAN] key to search for FM radio stations. While setting the RX CTCSS/DCS, press the key [*SCAN] to scan the RX CTCSS/DCS.
  • [#] KEY: Under channel mode, press [#] key to switch High/Low transmit power. Press [#] key for 2 seconds to lock/unlock the keypad.

8. LCD Display

The display icons appear when certain operations or specific features are activated.

Diagram of the LCD display showing various icons and their meanings, including operating channel, operating frequency, CTCSS/DCS activated, frequency offset direction, Dual Watch, VOX, Reverse, Wide Band, Battery Level, Keypad lock, Low transmit power, and Signal Strength Level.
Figure 12: LCD Display Icons.
LCD Icon Descriptions
IconDescription
CH-009Operating channel.
400.000.00Operating frequency.
CT'CTCSS' activated.
DCS'DCS' activated.
+/-Frequency offset direction for accessing repeaters.
SDual Watch/Dual Reception functions activated.
VOXFunction 'VOX' enabled.
RReverse function activated.
NWide Band selected.
Battery IconBattery Level indicator.
Keypad Lock IconKeypad lock function activated.
LLow transmit power.
Signal Strength BarsSignal Strength Level.

9. Basic Operation

11.1. Radio ON-OFF/Volume Control

Make sure the antenna and battery are installed correctly and the battery is charged. Rotate the knob clockwise to turn the radio on. Rotate the knob fully counter-clockwise until a 'click' is heard to turn the radio off. Turn the knob clockwise to increase the volume, or counter-clockwise to decrease the volume.

11.2. Selecting a Frequency or Channel

Press the [▲] or [▼] key to select the desired frequency/channel. The display shows the selected frequency/channel. Press and hold down the [▲] or [▼] key for fast frequency up or down. You cannot select a channel if it is not previously stored.

10. 1750 Hz Tone for Access to Repeaters

To establish long-distance communications through an amateur radio repeater, which is activated after receiving a 1750 Hz tone, press and hold the [PTT] button, then press the [BAND] button to transmit a 1750Hz tone.

10. Advanced Operation

You can program your transceiver's operating parameters through the setup menu to suit your needs or preferences.

12.1. Set Menu Description

The following table outlines the menu options and their available settings:

Menu Options and Settings
Menu No.Function/DescriptionAvailable Settings
0SQL (Squelch level)0-9
1STEP (Frequency step)2.5/5/6.25/10/12.5/25kHz
2TXP (Transmit power)HIGH/LOW
3SAVE (Battery save, 1:1/1:2/1:3/1:4)OFF/1/2/3/4
4VOX (Voice operated transmission)OFF/0-10
5W/N (Wideband/narrowband)WIDE/NARR
6ABR (Display illumination)OFF/1/2/3/4/5s
7TDR (Dual watch/dual reception)OFF/ON
8BEEP (Keypad beep)OFF/ON
9TOT (Transmission timer)15/30/45/60.../585/600 seconds
10R-DCS (Reception digital coded squelch)OFF/D023N...D754I
11R-CTS (Reception Continuous Tone Coded Squelch)67.0Hz...254.1Hz
14VOICE (Voice prompt)OFF/ON
15ANI (Automatic number identification of the radio, only can be set by PC software.)
16DTMFST (The DTMF tone of transmitting code.)OFF/DT-ST/ANI-ST/DT+ANI
17S-CODE (Signal code, only could be set by PC software.)1,...,15 groups
18SC-REV (Scan resume method)TO/CO/SE
19PTT-ID (press or release the PTT button to transmit the signal code)OFF/BOT/EOT/BOTH
20PTTLT (delay the signal code sending)0,...,30ms
21MDF-A (under channel mode, A channel displays. Note:name display only can be set by PC software.)FREQ/CH/NAME
22MDF-B (under channel mode, B channel displays. Note:name display only can be set by PC software.)FREQ/CH/NAME
23BCL (busy channel lockout)OFF/ON
24AUTOLK (keypad locked automatically)OFF/ON
25SFT-D (direction of frequency shift)OFF/+/-
26OFFSET (frequency shift)00.000...69.990
27MEMCH (stored in memory channels)000,...127
28DELCH (delete the memory channels)000,...127
29WT-LED (illumination display color of standby)OFF/BLUE/ORANGE/PURPLE
30RX-LED (illumination display color of reception)OFF/BLUE/ORANGE/PURPLE
31TX-LED (illumination display color of transmitting)OFF/BLUE/ORANGE/PURPLE
32AL-MOD (alarm mode)SITE/TONE/CODE
33BAND (band selection)VHF/UHF
34TX-AB (transmitting selection while in dual watch/reception)OFF/A/B
35STE (Tail Tone Elimination)OFF/ON
36RP_STE (Tail tone elimination in communication through repeater)OFF/1,2,3...10
37RPT_RL (Delay the tail tone of repeater)OFF/1,2,3...10
38PONMGS (Boot display)FULL/MGS
39ROGER (tone end of transmission)ON/OFF
40RESET (Restore to default setting)VFO/ALL

12.2. Shortcut Menu Operation

  1. Press the MENU key, then press the [▲] or [▼] key to select the desired menu.
  2. Press the MENU key again to enter the parameter setting.
  3. Press the [▲] or [▼] key to select the desired parameter.
  4. Press the MENU key to confirm and save. Press the EXIT key to cancel setting or clear the input.

12.3. "SQL" (Squelch)

The squelch mutes the speaker of the transceiver in the absence of reception. With the squelch level correctly set, you will hear sound only while actually receiving signals and significantly reduce battery current consumption. It is recommended that you set Level 5.

12.4. Function "VOX" (Voice Operated Transmission)

This function allows transmission without needing to push the [PTT] on the transceiver. Transmission is activated automatically by detecting the radio voice. When speaking finishes, the transmission automatically terminates and the transceiver will automatically receive a signal. Be sure to adjust the VOX Gain level to an appropriate sensitivity to allow smooth transmission.

12.5. Select Wideband or Narrowband "W/N"

In areas where RF signals are saturated, you must use the narrow band of transmission to avoid interference in adjacent channels.

12.6. TDR (Dual Watch/Dual Reception)

This feature allows you to operate between frequency A and frequency B. Periodically, the transceiver checks whether a signal is received on another frequency that you have scheduled. If a signal is received, the unit will remain on that frequency until the received signal disappears.

12.7. TOT (Transmission Timer)

This function automatically controls the time you transmit each time you press [PTT] on the transceiver. This feature is very useful to avoid overheating excessive power transistors. The transceiver will automatically stop transmission once the set time is reached.

12.8. CTCSS/DCS

In some cases, you may only want to establish communications in a closed user group at a particular frequency or channel. For this, you will use "CTCSS" or "DCS" codes for reception. The "squelch" opens only when receiving a frequency with the same "CTCSS" or "DCS" codes as programmed in your transceiver. If the received signal's codes differ from those programmed in your transceiver, the "squelch" will not open, but the received signal can still be heard.

Note: The use of "CTCSS" or "DCS" in communication does not guarantee complete confidentiality.

12.9. ANI (Automatic Number Identification)

ANI is also known as PTT ID because an ID is transmitted when the PTT button of the radio is pressed and/or released. This ID tells the dispatcher which field radio was keyed. This feature can only be set by PC software.

12.10. DTMFST (DTMF Tone of Transmitting Code)

First, set the PTT-ID as BOT/EOT/BOTH.

  • "OFF": Under transmitting mode, you won't hear the DTMF tone while pressing the key to transmit the code or code automatically transmitted.
  • "DT-ST": Under transmitting mode, you will hear the DTMF tone while pressing the key to transmit the code.
  • "ANI-ST": Under transmitting mode, you will hear the DTMF tone while the code is automatically transmitted.
  • "DT-ANI": Under transmitting mode, you will hear the DTMF tone while you press the key to transmit the code or the code automatically transmitted.

12.11. SC-REV (Scan Resume Method)

This transceiver allows you to scan memory channels, all bands, or part of the bands. When the transceiver detects a communication, the scan will stop automatically.

Notes on Scan Resume Method:

  • "TO" (Time Operation): Scanning will stop when it detects an active signal. The scanning will resume automatically after a predetermined time.
  • "CO" (Carrier Operation): The scanning will stop and remain on the frequency or channel until the active signal disappears.
  • "SE" (Search Operation): The scanning will stop and remain on the frequency or channel after it detects an active signal.

12.12. PTT-ID (PTT or Release PTT to Transmit the Signal Code)

This feature allows you to know who is calling you.

  • "OFF": Don't transmit the code while pushing the PTT button.
  • "BOT": Transmit the code while pushing the PTT button (code can only be set by PC software).
  • "EOT": Transmit the code while releasing the PTT button.
  • "BOTH": Transmit the code while pushing or releasing the PTT button.

12.13. BCL (Busy Channel Lockout)

The BCLO feature prevents the radio's transmitter from being activated if a signal strong enough to break through the "noise" squelch is present. On a frequency where stations using different CTCSS or DCS codes may be active, BCLO prevents you from disrupting their communications accidentally (because your radio may be muted by its own tone decoder).

12.14. SFT-D (Direction of Frequency Shift)

The "OFFSET" is the difference or offset between the reception frequency and the transmission frequency for access to amateur radio repeaters. Set the "OFFSET" according to the amateur radio repeater through which you want to communicate.

12.15. OFFSET (Frequency Shift)

When communicating via a repeater, the direction of displacement of frequency should be timed so that the transmission frequency is higher or lower than the receiving frequency.

12.16. STE (Tail Tone Elimination)

This function activates or deactivates the transmission end tone. This final tone transmission should only be used in communications between transceivers and not through a repeater, which must be deactivated.

13. CTCSS Table

CTCSS Tones (Hz)
No.Tone(Hz)No.Tone(Hz)No.Tone(Hz)No.Tone(Hz)No.Tone(Hz)
167.01194.821131.831171.341203.5
269.31297.422136.532173.842206.5
371.913100.023141.333177.343210.7
474.414103.524146.234179.944218.1
577.015107.225151.435183.545225.7
679.716110.926156.736186.246229.1
782.517114.827159.837189.947233.6
885.418118.828162.238192.848241.8
988.519123.029165.539196.649250.3
1091.520127.330167.940199.550254.1

14. DCS Table

DCS Codes
No.CodeNo.CodeNo.CodeNo.CodeNo.Code
1D023N22D131N43D251N64D371N85D532N
2D025N23D132N44D252N65D411N86D546N
3D026N24D134N45D255N66D412N87D565N
4D031N25D143N46D261N67D413N88D606N
5D032N26D145N47D263N68D423N89D612N
6D036N27D152N48D265N69D431N90D624N
7D043N28D155N49D266N70D432N91D627N
8D047N29D156N50D271N71D445N92D631N
9D051N30D162N51D274N72D446N93D632N
10D053N31D165N52D306N73D452N94D645N
11D054N32D172N53D311N74D454N95D654N
12D065N33D174N54D315N75D455N96D662N
13D071N34D205N55D325N76D462N97D664N
14D072N35D212N56D331N77D464N98D703N
15D073N36D223N57D332N78D465N99D712N
16D074N37D225N58D343N79D466N100D723N
17D114N38D226N59D346N80D503N101D731N
18D115N39D243N60D351N81D506N102D732N
19D116N40D244N61D356N82D516N103D734N
20D122N41D245N62D364N83D523N104D743N
21D125N42D246N63D365N84D526N105D754N

11. Technical Specifications

15.1. General

General Specifications
AttributeValue
Frequency Range65MHz-108MHz (Commercial FM radio reception)
VHF: 136-174MHz (Rx/Tx)
UHF: 400-520MHz (Rx/Tx)
Memory ChannelsUp to 128 channels
Frequency Stability±2.5ppm
Frequency Step2.5kHz/5kHz/6.25kHz/10kHz/12.5kHz/25kHz
Antenna Impedance50Ω
Operating Temperature-20°C to +60°C
Supply VoltageRechargeable Lithium-Ion 7.4V/1800mAh
Consumption in Standby≤75mA
Consumption in Reception380mA
Consumption in Transmission≤1.4A
Mode of OperationSimplex or semi-duplex
Duty Cycle03/03/54 min. (Rx / Tx / Standby)
Dimensions58mm x 110mm x 32mm
Weight130g (approximate)
Wireless FunctionYes
Tuner TechnologyVHF, UHF
Storage Channel99CH
Display ScreenNo (UV-5R), Yes (UV-5R Mini)
Is it wirelessYes
Maximum Range3km-5km
Is it with batteryYes
Is Batteries IncludedYes
TypeCar, Portable, Ear Hook, Mini
Output Power(w)3w-5w
WaterproofIP45
MaterialPlastic
High-concerned chemicalNone
Item TypeMobile Radio
CertificationCE, FCC

15.2. Transmitter

Transmitter Specifications
AttributeValue
RF Power5W/1W
Type of ModulationFM
Emission Class16KΦF3E/11KΦF3E (W/N)
Maximum Deviation≤±5 kHz/ ≤±2.5 kHz (W/N)
Spurious Emissions<-60 dB
Diagram showing three power output modes: H-8W (High), M-4W (Mid), L-1W (Low). Note: Actual power output for this model is 3W-5W as per specifications.
Figure 13: Power Output Modes (Note: Actual power output for this model is 3W-5W as per specifications).

15.3. Receiver

Receiver Specifications
AttributeValue
Receiver Sensitivity0.2μV (at 12 dB SINAD)
Intermodulation60 dB
Audio Output1000mW
Adjacent Channel Selectivity65/60dB

Note: All specifications shown are subject to change without notice.

12. Troubleshooting

If you encounter any issues with your transceiver, refer to the table below for possible causes and solutions:

Troubleshooting Guide
ProblemPossible Cause / Solution
The radio does not start.The battery is low; replace with a charged battery or proceed to charge the battery. The battery is not installed correctly; remove and reattach it.
The battery runs down quickly.The battery life has come to an end; replace the battery with a new one. The battery is fully charged; make sure the battery is made in full.
The receiving indicator LED lights but no sound from the speaker.Make sure the volume setting is too low. Make sure the undertones "CTCSS" or code "DCS" are the same as those programmed in the transceiver of the other members of your group.
When transmitting, other members of your group do not receive the communication.Make sure the undertones "CTCSS" or code "DCS" programmed in your transceiver are the same as those programmed in the transceiver of the other members of your group. Your partner or you are too far. You or your partner are in a bad area of RF signal propagation.
In "standby" mode, the transceiver transmits without pressing the "PTT".Check if the level adjustment function "VOX" is set too sensitive.
Receive communications from other user groups while communicating with your group.Change frequency or channel. Change the undertones "CTCSS" or code "DCS" in your group.
Communication with other members of your group is poor or low quality.You or your partner is too far away or in an area of poor radio signal propagation, such as inside a tunnel, an underground car park, in a mountainous area, including large metal structures, etc.

Once these checks, if you still have problems with the transceiver, check with your distributor, dealer or service center.

13. User Tips

No specific user tips were found from external reviews or Q&A for this product. However, general best practices for walkie-talkie usage include:

  • Clear Communication: Speak clearly and concisely. Avoid shouting into the microphone.
  • Battery Management: Always carry a spare charged battery for extended use, especially in cold weather.
  • Antenna Care: Ensure the antenna is securely attached and not damaged for optimal signal quality.
  • Programming Software: For advanced customization and channel management, consider using the PC programming software.
  • Range Awareness: Be mindful of environmental factors (buildings, terrain) that can affect communication range.

14. Warranty and Support

17. Warranty

The device described in this Certificate is guaranteed for a period of one year from the date of sale to the final user. This Warranty Certificate is unique and not transferable and may not be reissued for new or original or copy. Substitution of product failure or any part thereof shall not involve extension of the guarantee.

The warranty covers the replacement and free replacement of all parts that are defective in materials and components used in manufacturing and/or assembly of the apparatus.

The warranty does not cover any faults caused by accident, improper installation and use, electric shock (e.g., storms), connection to a power source other than that specified, reverse polarity in the diet, or claims due to deterioration in the external appearance from normal use, nor the amount or condition of the accessories.

Checking the accessories is the responsibility of the purchaser at the time of purchasing the device.

The warranty does not cover rechargeable batteries even if they are part of the equipment purchased as they are considered consumables. The impairment must be reported within a period of fifteen days from the date of purchase.

The warranty is void on the following assumptions:

  1. Devices that have been manipulated by another or by anyone other than an authorized service provider.
  2. Equipment and accessories in which the serial number has been altered, deleted, or filed unreadable.
  3. Use of the product other than as intended.

To make use of the guarantee, it is necessary to give the dealer or any of the Authorized Service the defective device with its accessories and the following documentation:

  1. Warranty Certificate duly completed and sealed.
  2. Original invoice which clearly identifies the device and the date of purchase.
  3. Description of the faults.

The warranty terms contained in this Certificate of Guarantee do not exclude, modify, or restrict the statutory rights of the buyer by virtue of the laws in force at the time of purchase, but are added to them.

User Manual (PDF)

A detailed user manual in PDF format is available for download. You can access it here: Baofeng UV-5R / UV-5R Mini User Manual (PDF)

15. Official Product Video

Watch the official video showcasing the Baofeng manufacturing process and product range:

Video: Baofeng Manufacturing Process and Product Showcase.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.