Introduction
Thank you for choosing the Xiaomi Mijia Smart Thermal Cup. This manual provides essential information for the safe and efficient use of your new thermal cup. Designed for convenience and performance, this 500ML vacuum cup features a 316L stainless steel inner liner, offering excellent thermal insulation for hot beverages and cold retention for chilled drinks.
Safety Information
- Do not use the cup in a microwave oven, dishwasher, or freezer.
- Keep out of reach of children when filled with hot liquids.
- Ensure the lid is securely closed to prevent leaks and spills, especially when carrying hot beverages.
- Do not overfill the cup; leave space for the lid to prevent overflow.
- Avoid dropping or subjecting the cup to strong impacts, as this may damage the vacuum insulation.
- Do not use abrasive cleaners or scrubbers that could scratch the surface or inner lining.
- This product is not intended for carbonated drinks, dry ice, or dairy products, as pressure buildup or spoilage may occur.
Package Contents
The package includes:
- 1 x Xiaomi Mijia Smart Thermal Cup (500ML)
Product Overview
The Mijia Smart Thermal Cup is designed for optimal temperature retention and portability. Key features include:
- 316L Stainless Steel Inner Liner: Ensures purity and safety for various beverages, resistant to heat and corrosion.
- High Vacuum Insulation Layer: Provides long-lasting thermal and cold retention.
- Thin Inner Wall (0.12mm): Achieved through a spiral spinning process and thin-walled laser welding for efficient insulation.
- PP Drinking Spout: Safe and odorless material for direct drinking.
- Threaded Rotary Lid: Designed for efficient sealing to prevent leaks.
- Silicone Bottom Pad: Offers anti-slip and wear-resistant properties.
- 500ML Large Capacity: Suitable for daily hydration needs, travel, and office use.
Setup
- Unpack: Carefully remove the thermal cup from its packaging.
- Initial Cleaning: Before first use, wash the inside and outside of the cup and the lid with warm water and a mild detergent. Rinse thoroughly.
- Inspect: Check for any damage or missing parts.
Operating Instructions
Filling the Cup
- Unscrew the lid by rotating it counter-clockwise.
- Pour your desired beverage into the cup. Do not fill past the inner thread line to ensure proper sealing and prevent spills.
- For best thermal performance, pre-heat the cup with hot water for 5-10 minutes before adding hot beverages, or pre-chill with cold water for 5-10 minutes before adding cold beverages.
- Securely screw the lid back on by rotating it clockwise until it is tight.
Using for Hot Beverages
The cup is designed to keep liquids above 68°C for up to 6 hours under standard test conditions (room temperature 20°C ± 5°C, initial water temperature 95°C).
Using for Cold Beverages
The cup is designed to keep liquids below 10°C for up to 6 hours under standard test conditions (room temperature 20°C ± 5°C, initial water temperature 4°C).
Maintenance and Care
- Daily Cleaning: After each use, wash the cup and lid with warm water and mild dish soap. Use a soft brush for the interior if needed.
- Deep Cleaning: For stubborn stains or odors, a mixture of baking soda and warm water can be used. Let it sit for a few hours before rinsing thoroughly.
- Drying: Ensure all parts are completely dry before reassembling and storing to prevent mold or mildew. Store with the lid off to allow air circulation.
- Avoid Harsh Chemicals: Do not use bleach or cleaners containing chlorine, as these can damage the stainless steel.
- Lid Care: Periodically check the silicone seal on the lid for wear and tear. A damaged seal can affect insulation and lead to leaks.
Troubleshooting
- Leaking: Ensure the lid is screwed on tightly and the silicone seal is properly seated and undamaged. Do not overfill the cup.
- Poor Insulation: Pre-heat or pre-chill the cup before use. Ensure the lid is fully sealed. Damage to the vacuum seal (e.g., from dropping) can impair insulation performance.
- Unpleasant Odor: Clean the cup thoroughly with warm water and baking soda. Ensure it is completely dry before storage.
Specifications
| Feature | Detail |
|---|---|
| Product Name | Mijia Light Enjoy Thermal Cup |
| Model Number | MJBWB01PL |
| Dimensions | 65 × 65 × 217 mm |
| Capacity | 500 mL |
| Net Weight | Approx. 215 g |
| Colors Available | White, Navy Blue, Light Blue |
| Thermal Insulation Performance | ≥ 68°C (6 hours) |
| Cold Insulation Performance | ≤ 10°C (6 hours) |
| Inner Material | 316L Stainless Steel |
| Drinking Spout Material | PP (Polypropylene) |
For more detailed information, you may refer to the User Manual (PDF).
User Tips
- For maximum heat retention, always pre-heat the cup with hot water before adding your hot beverage.
- To keep drinks colder for longer, pre-chill the cup with ice water.
- The slim design makes it easy to carry in bags without taking up much space.
- The leak-proof design ensures peace of mind when carrying it on the go.
Warranty and Support
This product comes with a standard manufacturer's warranty. For warranty claims or technical support, please contact the retailer or Xiaomi customer service with your purchase details. Keep your proof of purchase for any warranty-related inquiries.