RACBOX 92201-2X000

Contents

RACBOX Fog Lamp Assembly

Model: 92201-2X000 (H11 Fog Lamp for KIA Soul 2010-2011)

1. Important Safety Information

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.

2. Setup and Installation

This section provides step-by-step instructions for installing your new fog lamp assembly. Ensure the vehicle is off and cool before beginning.

RACBOX Fog Lamp Assembly Overview

Figure 1: Overview of the RACBOX Fog Lamp Assembly, showing front and rear views, an illuminated light, and an installed unit on a vehicle.

  1. Prepare Vehicle: Turn off the vehicle engine and disconnect the power supply to avoid short circuits.
  2. Locate Mounting Position: Identify the mounting position of the original fog light on your vehicle.
  3. Remove Old Assembly: Remove the fixing screws or clips that hold the stock light assembly in place.
  4. Disconnect Wiring: Unplug the power connector from the original fog light and carefully remove the old assembly.
  5. Install New Assembly: Install the new fog light assembly into the mounting position.
  6. Secure Assembly: Secure the light assembly with screws or clips to ensure stable installation.
  7. Connect Power: Connect the power plug correctly. If the light does not work after connection, reverse the plug polarity.
Rear view of fog light with H11 bulb

Figure 2: Rear view of the fog lamp assembly showing the H11 bulb socket and bulb insertion point.

3. Operating Instructions

Once installed, your fog lights operate in conjunction with your vehicle's lighting system.

  1. Function Test: After installation, test all light functions to ensure normal operation.
  2. Connection Check: Recheck all screws and connections to make sure they are firm and reliable.
  3. Activation: Activate the fog lights using your vehicle's designated fog light switch, typically located on the dashboard or turn signal stalk.
Illuminated fog light showing yellow light output

Figure 3: Close-up of the fog light illuminated, showcasing its yellow (4300K) light output.

4. Maintenance

To ensure optimal performance and longevity of your fog lamps, follow these simple maintenance tips:

  • Cleaning: Regularly clean the fog lamp lenses with a soft cloth and mild soap solution to remove dirt and road grime. Avoid abrasive cleaners.
  • Inspection: Periodically inspect the lamps for any signs of damage, cracks, or loose connections. Address any issues promptly.
  • Bulb Replacement: If a bulb burns out, replace it with an H11 type bulb. Refer to your vehicle's manual for specific bulb replacement procedures, or follow general automotive bulb replacement guidelines.

5. Troubleshooting

If you encounter issues with your fog lamp assembly, try the following steps:

  • Light Not Working: If the fog light does not illuminate after installation, ensure the power plug is connected correctly. If it still doesn't work, try reversing the plug polarity.
  • Check Connections: Verify that all electrical connections are secure and free from corrosion.
  • Check Bulb: Inspect the H11 bulb to ensure it is not burnt out or damaged. Replace if necessary.
  • Vehicle Fuse: Consult your vehicle's owner manual to locate and check the fuse for the fog lights. Replace if blown.

6. Specifications

BrandRACBOX
Model Name92201-2X000 (H11 fog lamp for KIA Soul 2010 2011)
Item TypeFog Lamp Assembly
Voltage12 V
Bulb TypeH11
Light ColorYellow (4300K)
MaterialPlastic
OEM NO.92201-2X000
FitmentFor KIA Soul 2010-2011
Package Dimensions (L x W x H)19 cm x 14 cm x 14 cm
Package Weight0.73 kg

7. User Tips

  • Always ensure a secure and tight fit for the fog lamp assembly to prevent vibration and potential damage.
  • Double-check wiring connections before fully reassembling any vehicle trim.

8. Warranty and Support

This product is an auxiliary accessory for automotive lighting, designed for normal replacement and upgrade. It meets relevant national automotive lighting industry standards and has undergone strict quality testing.

Standard manufacturer warranty applies to this product. For support or warranty claims, please contact the manufacturer or your point of purchase.

Manufacturer Information:

Guangzhou Bai Ji Tun Trading Co., Ltd
C116, No.1489, Fanghua Road Baiyun
Guangzhou, China
Email: tdlaccount@126.com

EU Authorized Representative:

APEX CE SPECIALISTS LIMITED
UNIT 3D NORTH POINT HOUSE, NORTH POINT BUSINESS PARK
NEW MALLOW ROAD, CORK, T23 AT2P, IRELAND
Email: info@apex-ce.com

For further assistance, please refer to the official user manual PDF: View User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.