JETTING Add-a-circuit Fuse Tap Adapter

Contents

12V Add-a-Circuit Fuse Holder Tap Adapter User Manual

Model: Add-a-circuit Fuse Tap Adapter

Introduction

The JETTING 12V Add-a-Circuit Fuse Holder Tap Adapter is designed to provide a convenient and safe way to add a new circuit to your vehicle's electrical system without cutting or splicing existing wires. It offers enhanced safety by protecting against overloads and simplifies the process of adding accessories.

This manual provides essential information for the safe and effective use of your fuse tap adapter. Please read it thoroughly before installation and operation.

Safety Information & Warnings

  • CHOKING HAZARD: This product contains small parts and is not suitable for children under 3 years of age. Keep out of reach of children.
  • Always consult a professional if you are unsure about electrical connections or vehicle wiring. Improper installation can lead to damage or injury.
  • Ensure the fuse holder is kept dry and away from moisture to prevent electrical hazards.
  • Store the product in a cool, dry place to prevent damage when not in use.
  • Always use a new fuse of the same rating as the original fuse when replacing.
  • Never exceed the maximum current rating of the fuse tap or the circuit you are tapping into.

Package Contents

Your package should contain the following items:

  • 2 x Add-a-Circuit Fuse Holder Tap Adapters (various types may be included, e.g., Micro2, Mini, Low Profile Mini, Standard)
  • Assorted Fuses (may vary by package)
Assortment of Add-a-Circuit Fuse Taps and Fuses
Figure 1: Assortment of Add-a-Circuit Fuse Taps and Fuses
Variety of Fuse Taps and Fuses Included in the Package
Figure 2: Variety of Fuse Taps and Fuses Included in the Package

Installation & Setup

The add-a-circuit design allows for quick power tapping without cutting original vehicle wiring.

  1. Identify the Correct Fuse Slot: Locate your vehicle's fuse box (usually under the dashboard or in the engine bay). Consult your vehicle's manual to find a suitable fuse slot for your new accessory. It's recommended to use a fuse that is only active when the ignition is on, or a constant power fuse depending on your accessory's needs.
  2. Select the Correct Fuse Tap Type: The fuse tap adapters come in various sizes (Micro2, Mini, Low Profile Mini, Standard) to match different vehicle fuse types. Ensure you select the correct type for the fuse slot you intend to use.
  3. Prepare the Wire Lead: Connect the wire from your new accessory to the wire lead of the fuse tap adapter. This typically involves crimping the accessory wire into the blue terminal on the fuse tap's wire lead.
  4. Insert Fuses:
    • Insert the original factory fuse (the fuse you removed from the vehicle's fuse box) into the lower slot of the fuse tap. This fuse protects the original circuit.
    • Insert a new fuse of the appropriate rating for your new accessory into the upper slot of the fuse tap. This fuse protects the new circuit.
  5. Install the Fuse Tap: Insert the fuse tap adapter into the empty fuse slot in your vehicle's fuse box. Ensure it is seated firmly.
  6. Test the New Circuit: Turn on your vehicle's ignition and test the newly installed accessory to ensure it functions correctly.
Effortless Installation of Fuse Tap in Vehicle Fuse Box
Figure 3: Fuse tap installed in a vehicle fuse box.
Diagram of Fuse Tap Types: Standard, Mini, Low Profile Mini, Micro2
Figure 4: Different fuse tap types and their components (Original Factory Fuse, Fuse For New Circuit, Fits into Fuse Slot, Wire Lead).
Steps for Connecting a Wire to the Fuse Tap Terminal
Figure 5: Visual guide for connecting the accessory wire to the fuse tap's terminal.

Operation

Once installed, the fuse tap adapter operates automatically. It provides power to your new accessory while protecting both the original and new circuits with their respective fuses. If an overload occurs on either circuit, the corresponding fuse will blow, interrupting the power flow and preventing damage.

Many fuse holders feature transparent covers, allowing for easy visual inspection to determine if a fuse has blown.

Maintenance

Fuse Replacement

If your accessory stops working or you suspect a blown fuse:

  1. Identify the Blown Fuse: Check the transparent cover of the fuse tap. A blown fuse will typically have a broken filament visible through the transparent casing.
  2. Remove the Blown Fuse: Carefully pull out the blown fuse from its slot in the fuse tap.
  3. Insert a New Fuse: Insert a new fuse of the same amperage rating into the empty slot. Ensure it is securely seated.
  4. Test: Verify that your accessory is now functioning correctly. If the new fuse blows immediately, there may be a short circuit or an issue with the accessory drawing too much current. Consult a professional if the problem persists.

General Care

  • Regularly inspect the fuse tap and connections for any signs of wear, corrosion, or loose wiring.
  • Keep the fuse box area clean and free from debris.

Troubleshooting

  • Accessory not receiving power:
    • Check both fuses in the fuse tap. Replace any blown fuses with the correct rating.
    • Ensure the fuse tap is fully seated in the vehicle's fuse box.
    • Verify the accessory's wiring connection to the fuse tap is secure.
    • Confirm the chosen fuse slot in the vehicle's fuse box provides power when expected (e.g., ignition on).
  • New fuse blows immediately after replacement: This indicates an overload or short circuit in the new accessory or its wiring. Disconnect the accessory and inspect its wiring for damage or incorrect connections. Do not continue to replace fuses without addressing the underlying issue.
  • Original circuit fuse blows: This is less common but could indicate an issue with the original circuit or that the original fuse rating was too low for the combined load. Ensure the original fuse rating is appropriate for the circuit.

Specifications

Feature Detail
Brand Name JETTING
Material Plastic
Voltage Compatibility 12V (Low voltage: Below 50Vac or 75Vdc)
Fuse Types Supported Micro2, Mini, Low Profile Mini, Standard, ATM Auto Fuses
Origin Mainland China
Package Dimensions (approx.) Length: 17 cm (6.7 in), Width: 3 cm (1.2 in), Height: 2 cm (0.8 in)
Package Weight (approx.) 0.025 kg (0.055 lbs)
Dimensions of Micro2, Mini, Low Profile Mini, and Standard Fuse Taps
Figure 6: Detailed dimensions for various fuse tap types.

User Tips

  • Always double-check the fuse type and rating required for both the original circuit and your new accessory before installation.
  • When crimping wires, ensure a strong and secure connection to prevent intermittent power or shorts.
  • Consider using a fuse puller tool for easier and safer fuse removal and insertion.
  • If adding multiple accessories, distribute them across different fuse taps and circuits to avoid overloading a single circuit.

Warranty & Support

For any issues, questions, or support regarding your JETTING Add-a-Circuit Fuse Holder Tap Adapter, please contact our store support. We are committed to providing assistance and ensuring your satisfaction.

A detailed user manual in PDF format is also available for download. Please refer to the product page for the link.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.