1. Introduction
Thank you for choosing the Redox 2.4G Wireless Split Keyboard Kit. This ergonomic mechanical keyboard features a split design, 2.4G wireless connectivity, hot-swappable switches, and VIAL software support for extensive customization. This manual provides essential information for setting up, operating, and maintaining your keyboard.
2. Safety Information
- Keep the keyboard away from liquids and excessive moisture.
- Avoid extreme temperatures.
- Do not attempt to disassemble or repair the keyboard yourself, as this may void the warranty and cause damage.
- Dispose of batteries according to local regulations.
3. Package Contents
The Redox 2.4G Wireless Split Keyboard Kit typically includes the following components:
- Left Keyboard Half
- Right Keyboard Half
- 2.4G USB Receiver
- (Optional, depending on kit variant) Mechanical Switches
- (Optional, depending on kit variant) Keycaps
- (Optional) USB-C Cable for initial setup/firmware flashing (not for wired operation)
4. Setup Guide
4.1. Battery Installation
The keyboard uses CR2032 button batteries for power. Locate the battery compartments on the underside of each keyboard half. Insert one CR2032 battery into each compartment, ensuring correct polarity (+/-). The keyboard is designed for ultra-low power consumption, providing long battery life.
4.2. Switch and Keycap Installation (for kits without pre-installed components)
If your kit did not come with switches and keycaps pre-installed, follow these steps:
- **Install Switches**: Align the pins of each mechanical switch with the hot-swap sockets on the PCB. Gently press down until the switch clicks into place. Ensure the pins are straight to avoid bending.
- **Install Keycaps**: Place the appropriate keycap onto the stem of each installed switch. Press firmly until it is seated securely.
4.3. Connecting to Your Computer
- Insert the 2.4G USB receiver into an available USB port on your computer.
- Ensure both keyboard halves are powered on (if they have an on/off switch).
- The keyboard should automatically connect to the receiver. No additional pairing steps are typically required.
5. Operating Instructions
5.1. Basic Usage
Once connected, the keyboard functions like a standard keyboard. The split ergonomic design allows for a more natural hand and wrist position.
5.2. Customizing Key Layouts with VIAL
The Redox keyboard supports VIAL, an open-source keyboard configurator, allowing you to remap keys, create macros, and manage multiple layers. This keyboard only supports 2.4G single mode and does not support wired or Bluetooth connections for operation.
- **Download VIAL**: Visit the official VIAL website to download the latest version of the software compatible with your operating system.
- **Connect Keyboard**: Ensure your keyboard is connected via the 2.4G USB receiver.
- **Open VIAL**: Launch the VIAL application. It should automatically detect your Redox keyboard.
- **Remap Keys**: Use the graphical interface to drag and drop key assignments, create custom layers, and configure macros.
- **Save Changes**: Changes made in VIAL are applied in real-time to the keyboard's firmware.
6. Maintenance
6.1. Cleaning
- Use a soft, dry cloth to wipe down the keyboard surface.
- For deeper cleaning, remove keycaps and use compressed air to clear debris from between switches.
- Avoid using harsh chemicals or abrasive materials.
6.2. Battery Replacement
When the keyboard's performance degrades or it stops responding, it may be time to replace the CR2032 batteries. Follow the installation steps in Section 4.1.
6.3. Switch Replacement
Thanks to the hot-swappable design, you can easily replace switches without soldering:
- Gently remove the keycap from the switch you wish to replace using a keycap puller.
- Use a switch puller to carefully grip the top and bottom clips of the switch and pull it straight up from the PCB.
- Align the pins of the new switch with the hot-swap sockets and press down until it clicks into place.
- Re-attach the keycap.
7. Troubleshooting
- **Keyboard not responding**: Check if the batteries are correctly installed and charged. Ensure the 2.4G USB receiver is securely plugged into your computer. Try a different USB port.
- **Specific keys not working**: If your kit is hot-swappable, try removing and re-inserting the switch for the affected key. Ensure the switch pins are not bent.
- **VIAL not detecting keyboard**: Make sure the keyboard is powered on and the 2.4G receiver is connected. Restart the VIAL software and/or your computer.
- **Connectivity issues**: Ensure there are no major obstructions or sources of interference between the keyboard and the USB receiver.
8. Specifications
| Feature | Description |
|---|---|
| Connectivity | 2.4G Wireless (single mode only, no wired or Bluetooth support) |
| Case Material | 3D Printed PLA |
| Switches | Hot-swappable |
| Battery Type | CR2032 Button Battery (ultra-low power consumption) |
| Ergonomics | Split Ergodox-style design |
| Customization Software | VIAL (full key custom remapping) |
| Full Size Keyboard | No |
| Wrist Support | No |
| Backlight Type | No backlight |
| Package Dimensions (approx.) | 15cm x 15cm x 15cm |
| Package Weight (approx.) | 0.7 kg |
9. Warranty and Support
For warranty information and technical support, please refer to the seller or the official product page. If you require specific usage methods not covered in this manual, please contact customer service.
A user manual in PDF format is available for download: Redox 2.4G Wireless Split Keyboard User Manual (PDF)
10. User Tips
No specific user tips were available from the provided data. However, general tips for split ergonomic keyboards include:
- Experiment with the split angle and distance between the halves to find your most comfortable typing position.
- Utilize the VIAL software to customize key layouts that suit your workflow, especially for frequently used commands or symbols.
- Consider using different switch types for different key zones (e.g., lighter switches for alphas, heavier for modifiers) if you frequently swap switches.