LS VISION MS5-4G-20X-EAU

Contents

LS VISION MS5-4G-20X-EAU Solar 4G/WiFi Security Camera User Manual

Model: MS5-4G-20X-EAU

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your LS VISION MS5-4G-20X-EAU Solar 4G/WiFi Security Camera. This advanced surveillance camera features dual-lens technology, 20X optical zoom, AI-powered detection, and continuous 24/7 recording, all powered by a solar panel and built-in battery for reliable outdoor use.

⚠️ Disclaimer: Camera products can only be used for purposes permissible under applicable law and regulations. Misuse of the product for any illegal activities is strictly forbidden. Please comply with the applicable laws and regulations in your country/area.

2. What's Included

Please check the package contents carefully. If any items are missing or damaged, contact customer support.

Diagram showing all included components: Camera, Foldable Solar Panel, Solar Panel Bracket, Camera Bracket, User Manual, Type-C Charging Cable, Hex Wrench, Screws, Positioning Stickers, Quick Start Guide.
Figure 2.1: Package Contents
  1. Camera (1)
  2. Foldable Solar Panel (1)
  3. Solar Panel Bracket (1)
  4. Camera Bracket (1)
  5. User Manual (1)
  6. Type-C Charging Cable (1)
  7. Hex Wrench (1)
  8. Screws (1 set)
  9. Positioning Stickers (1 set)
  10. Quick Start Guide (1)

3. Product Overview

Familiarize yourself with the components and features of your security camera.

Diagram of the camera showing various parts like 5W Solar Panel, 433 Antenna, WiFi Antenna, Wide-angle Lens, Infrared LED, Microphone, White Light, PTZ Lens, PIR, Status LEDs, Angle-adjusting Screw for Solar Panel, Bracket Fixing Screw, Power Switch, Reset Button, Type-C Charging Port, Speaker, TF Card, Solar Panel Connection Cable.
Figure 3.1: Product Component Diagram

Key Components:

  • 5W Solar Panel: For continuous power supply.
  • 433 Antenna & WiFi Antenna: For network connectivity.
  • Wide-angle Lens: For broad area coverage.
  • PTZ Lens: For detailed monitoring with Pan, Tilt, and Zoom capabilities.
  • Infrared LED & White Light: For night vision and warning lights.
  • Microphone & Speaker: For two-way audio communication.
  • PIR Sensor: For passive infrared motion detection.
  • Status LEDs: Indicate device status.
  • Power Switch & Reset Button: For device control and reset.
  • Type-C Charging Port: For charging the built-in battery.
  • TF Card Slot: For local storage (supports up to 256GB).

4. Setup

4.1. Initial Boot Instructions

  1. Install Antennas: Install the corresponding A and B antennas in sequence.
  2. Initial Charge: For optimal performance, charge the camera for at least 10 hours before first use.
  3. Insert SIM and Memory Card:
    Diagram showing insertion of 4G nano SIM card and memory card.
    Figure 4.1: SIM and Memory Card Insertion
    • Insert the 4G nano SIM card: The notched side faces left, and the chip faces up.
    • Insert the memory card: The notched side faces right, and the chip faces up.

    4G Status LEDs:

    • Blue light off, Red light flashes Fast: SIM card read error.
    • Blue light off, Red light flashes Slowly: SIM card read, Cell data error.
  4. Power On and Reset:
    Diagram showing solar charging cable connection, power button, and reset button.
    Figure 4.2: Power On and Reset
    • Connect the solar charging cable.
    • Press the power button (self-locking switch) once to turn on the power.
    • After powering on, press and hold the reset button for 5 seconds until the camera is ready to match the network.

4.2. APP Download & Registration

  1. Download APP: Download the "NIVIEW" APP from your device's app store (App Store for iOS, Google Play for Android). You can also scan the QR code below or visit APP.NICEVIEWER.COM.
    QR code for NIVIEW APP download.
    Figure 4.3: NIVIEW APP QR Code
  2. Register: For better user experience and equipment protection, it is recommended that first-time users register using the verification code mode with their email. Set a strong password for confidentiality.

4.3. Configuration and Device Addition

  1. Add Camera: Run the NIVIEW app and click the "+" icon in the upper right corner to add a device.
  2. Choose Network Type: Select the "4G" option on the right.
  3. Confirm Camera Status: Follow the app prompts to check if the indicator light on the front of the camera is flashing alternately in red and blue. If it is, click "To connect". If not, ensure the camera is powered on and check the SIM card indicator status.
  4. Scan QR Code: Scan the camera's QR code, which is located on the back of the device.

4.4. Installation

The camera offers versatile mounting options including integrated wall-mount, separate wall-mount, and separate ceiling-mount (bracket sold separately).

Image showing integrated wall-mount, separate wall-mount, and separate ceiling-mount options for the camera and solar panel.
Figure 4.4: Versatile Mounting Options

4.4.1. Wall Mounted Installation

  1. Fix the solar panel and the bracket together using the hex wrench. Adjust the solar panel to face the maximum sunlight orientation according to your environment.
  2. Connect the solar panel charging port to the camera.
  3. Use screws to secure the iron wall bracket on the wall. Hang the camera from top to bottom, then lock the tamper-proof screws below.

4.4.2. Ceiling Mounted Installation

  1. Unscrew the fixing screw at point A and pull out the upper wall bracket.
  2. Put the upper wall bracket upright, insert it along the rail, and fix the screws.

4.5. Commissioning Instructions

  1. After adjusting the tilt angle of the wide-angle camera, tighten the thumbscrew to fix the lens position.
  2. According to monitoring requirements, manually adjust the up and down tilt angle of the wide-angle camera.
  3. Adjust the angle of the solar panel to achieve maximum sunlight exposure. The recommended orientation is 25 degrees inclination.
  4. The horizontal direction of the upper wide-angle camera bracket can be adjusted left and right, and the positioning screw can be fixed after adjustment.
  5. You can manually adjust the angle of the white light on both sides; the recommended angle is 15 degrees downward tilt.

5. Operating Instructions

5.1. APP Homepage Functions

  • Receive notifications: Get alerts from the camera.
  • Shared by family: View devices shared with you.
  • Battery status: Monitor the camera's power level.
  • Real-time monitoring: Access live camera feed.
  • Device Information: Access camera details.
  • Cloud service: Manage cloud storage.
  • Share with family: Share camera access with up to 8 accounts.

5.2. Sharing Function

After your family members have registered their accounts, you can share camera access with them via the app.

5.3. Do Not Disturb Mode

Access this setting from the top of the app's homepage. When PIR is triggered, you will receive real-time notifications. If you prefer not to receive notifications, you can enable Do Not Disturb mode.

5.4. Viewing the Event List

Click "Event" at the bottom of the app page to view a list of all triggered alarms.

5.5. Cloud Storage Service

You can purchase cloud storage packages directly from the app's homepage.

5.6. Manage Account Information

Click "Mine" at the bottom of the app page to access account settings, where you can modify your login password and manage other account functions.

5.7. Real-time Monitoring and Playback

5.7.1. Real-time Monitoring

Click the screen on the homepage to access the live camera feed.

5.7.2. Video Playback (Memory Card & Cloud Storage)

Click the video playback button on the homepage (from the pull-up control menu) to access recorded footage. You can select between memory card playback or cloud storage playback. You can adjust the playback time precision and filter by date.

5.8. Control Instructions

Access the control page via the pull-up menu to manage PTZ functions and other settings.

  • PTZ Control: Use the controls to pan (355°), tilt (90°), and zoom the camera.
  • Focus Calibration: If the optical zoom lens appears out of focus due to environmental changes, click to enter calibration mode. This process takes approximately 1 minute.
  • Tracking Calibration: If there is a discrepancy in the pan/tilt rotation direction, click the reset button. The camera will self-detect and calibrate its position.
  • Preset: Set and save specific camera positions for quick access and monitoring.
  • Guard: When human tracking is enabled, the camera will follow human subjects. Set a guard position to ensure critical areas are always monitored.

5.9. Intelligent Tracking and Linkage

In the detection settings, you can enable or disable humanoid tracking.

  • Linkage Calibration: If manual adjustment or misoperation causes errors in humanoid tracking by the PTZ camera, use the calibration function to re-calibrate the linkage between the upper and lower lenses. Click the designated button to initiate automatic calibration (takes about 3 minutes).
  • Finger Tracking Function: Tapping anywhere on the upper wide-angle screen will automatically position the PTZ lens below to that point.
  • Humanoid Tracking Function: When enabled, the camera uses the wide-angle camera to detect human shapes and links the PTZ camera for pan-tilt tracking. Double-clicking on the wide-angle screen will focus the lower monitor.
  • Humanoid Mark: A point frame will appear around detected persons within the monitoring range.

5.10. System Settings

Access quick settings and device information to check firmware versions, upgrade, and configure display modes and other system settings.

5.11. Memory Card Settings

Check the usage status of your TF card and format it if necessary.

5.12. Alert Push Settings

Configure which types of alarm notifications you wish to receive from the camera.

5.13. Detection Settings

Adjust motion detection settings, including sensitivity and detection distance.

5.14. Power Consumption Settings

Select the power mode based on your environment and needs to manage battery usage effectively.

  • Low power protection: Recommended. If battery drops below 10%, power-consuming functions (PIR, etc.) are automatically turned off.
  • Normal mode: Most energy-saving. Camera is in standby when not remotely monitored. Activates alarm and video recording for 15 seconds upon human detection.
  • Adaptive mode: Records 24/7 when battery is above 50%. Below 40%, switches to low-power mode.
  • All time mode: Camera operates continuously. Requires constant power supply.

5.15. Sound & Light Settings

Configure the working mode for infrared LEDs, white lights, and alarms.

  • Infrared lights control: Manage infrared LED behavior.
  • Color mode: White lights on at night for full-color camera video.
  • Night alarm mode: White lights flash and sound alarm when human passes by at night.
  • All day alarm mode: White lights flash and sound alarm when human passes by, day or night.

6. Specifications

FeatureSpecification
Model NumberMS5-4G-20X-EAU
Megapixels8MP (4K)
Lens QuantityDual Lens (2.8mm wide-angle + 3.2~12mm zoom)
Zoom20x Optical Zoom
Pan & TiltPan 355°, Tilt 100°
Connectivity4G and 2.4G WiFi (Dual Network)
Power SourceSolar Powered (20 Watt solar panel)
BatteryBuilt-in 20000mAh rechargeable batteries
Night VisionColor Night Vision, Infrared Light + White Light
IR Distance50m
AI FunctionsSmart Tracking, Humanoid Detection, Vehicle Detection, Pet Detection
StorageCloud Storage, TF Card (up to 256GB)
Video CompressionH.264, H.265
Operating Temperature-10°C to 60°C (14°F to 140°F)
IP RatingIP66 (Waterproof / Weatherproof)
Supported Mobile SystemsiOS, Android
APPNiview

6.1. Dimensions

Diagram showing the dimensions of the camera and solar panel. Camera: 170mm height, 98mm width, 126mm depth. Solar Panel: 400mm width, 220mm height.
Figure 6.1: Product Dimensions

6.2. 4G Technical Analysis (Band Specifications)

The camera supports various 4G bands depending on the region. Please refer to the table below for specific band information:

RegionFrequency Bands
ChinaLTE FDD:B1/B3/B5/B8, LTE TDD:B34/B38/B39/B40/B41, WCDMA:B1/B5/B8
EuropeFDD:B1/3/5/7/8/20, TDD:B38/40/41, WCDMA:B1/5/8, GSM:850/900/1800Mhz
North AmericaFDD:B2/4/12/13/17/66/71, WCDMA:B2/4/5
JapanFDD:B1/3/8/11/18/19/21/26/28, TDD:B41, WCDMA:B1/6/8/19
Latin AmericaFDD:B1/2/3/4/5/7/8/28/66, TDD:B38/40, WCDMA:B1/2/5/8, GSM:850/900/1800/1900Mhz
Europe AustraliaFDD:B1/3/5/7/8/20/28, TDD:B38/40/41, WCDMA:B1/5/8, GSM:850/900/1800Mhz

7. Troubleshooting (FAQ)

Q: Will the camera show red lights when night vision is activated?
A: The built-in infrared LEDs only emit dim red lights when night vision is active. The image quality remains clear without visible bright red lights.
Q: What is the longest recording time?
A: The camera has three working modes:
  • Low Power Consumption Mode (Default): Records for 15 seconds when motion is detected. Continuous recording occurs if motion persists. The 20000mAh battery supports 6000 wake-ups, with solar energy adding 250 wake-ups per hour, theoretically allowing continuous operation.
  • Adaptive Mode: Records 24 hours when the battery is above 50%. If power drops below 40%, it switches to low-power mode.
  • Full-Time Mode: Requires continuous power supply. If no power supply, it can operate for 36 hours.
Q: How to check video playback?
A: Click the video playback button on the app's homepage (from the pull-up control menu) and select either memory card playback or cloud storage playback.
Q: What happens when the memory card runs out of space?
A: The oldest footage will be overwritten by the newest. Regularly back up important videos or delete unnecessary ones to free up space. Alternatively, subscribe to a cloud plan.
Q: How many cameras can I connect to the same account?
A: You can add up to 50 cameras, but it is recommended to add no more than 10 devices for optimal experience.
Q: Why am I not receiving push notifications on my mobile device?
A: Ensure you have allowed the NiView App to push notifications to your mobile device in your phone's settings.
Q: How many accounts can a camera be shared with?
A: A camera can be shared with up to 8 accounts.
Q: What should I do if the optical zoom lens is out of focus?
A: If the lens is out of focus due to environmental changes, go to the PTZ control interface, adjust the viewing angle to the farthest reference object, click the "zoom calibration button", and wait for 1 minute.
Q: What should I do if PTZ lens tracking is inaccurate or incomplete?
A: Click the "linkage calibration button" at the top right of the homepage. The upper and lower lenses will then recalibrate their linkage coordinates.

8. User Tips

  • Initial Charging: For best results, fully charge the camera for at least 10 hours before its first use.
  • Battery Longevity: The camera's battery can be charged approximately 500 times. Regular charging (e.g., once a week) can extend battery life to over 9 years.
  • Solar Panel Placement: Ensure the solar panel is positioned to receive maximum direct sunlight for optimal charging and continuous operation.
  • Cold Weather Performance: In extremely cold temperatures (below -4°F / -20°C), battery performance may decrease, and charging might be affected. The camera will resume normal operation as temperatures rise.
  • Data Management: To prevent loss of important footage, regularly back up videos from the TF card or cloud storage.

9. Warranty and Support

For detailed warranty information and technical support, please refer to the official LS VISION website or contact your retailer. A comprehensive user manual in PDF format is available for download: User Manual (PDF).

© 2024 LS VISION. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.