Grennova GRE-N-2200

Contents

GRENNOVA 2200W Pure Sine Wave Inverter User Manual

Model: GRE-N-2200 | Brand: Grennova

1. Introduction

Thank you for choosing the Grennova 2200W Pure Sine Wave Inverter. This manual provides essential information for the safe and efficient operation, installation, and maintenance of your inverter. Please read it thoroughly before use.

GRENNOVA 2200W Pure Sine Wave Inverter

Figure 1: GRENNOVA 2200W Pure Sine Wave Inverter, front view showing display and output socket.

Video 1: Product overview and demonstration of the GRENNOVA 2200W Pure Sine Wave Inverter.

2. Safety & Precautions

WARNING: Failure to follow these safety instructions may result in electric shock, fire, or serious injury.

  • High Voltage Danger: The output sockets contain high-voltage AC identical to commercial power grids. DO NOT touch the inside of the sockets or operate with wet hands!
  • NO Reverse Polarity: When connecting the battery, you must STRICTLY distinguish the positive and negative poles (Red to Positive +, Black to Negative -). Reverse connection will blow internal fuses and cause permanent damage.
  • NO Grid Connection: Never plug the inverter's AC output into a wall outlet (commercial grid), as this will instantly destroy the unit.
  • Ventilation: The inverter generates heat during operation. Leave at least 10cm of clearance around the unit and never block the cooling fans.
  • Environment: Do not expose the inverter to rain, moisture, direct sunlight, or extreme temperatures.
  • Children: Keep the inverter out of reach of children.

3. Package Contents

Please check the package for the following items:

  • 1 x GRENNOVA Pure Sine Wave Inverter (2200W Peak / 1100W Rated)
  • 1 x User Manual
  • 1 Pair x Alligator Clips (for 12V/24V models) OR 1 x Specialized Wire (for 48V/60V models)
What's in the Box

Figure 2: Contents of the product package.

4. Setup Instructions

4.1. Critical - Input Voltage Matching

Ensure your battery system voltage matches the inverter's input voltage. Using an incorrect voltage will damage the inverter.

System VoltageInput Voltage Range
12V System9.5V - 15.5V
24V System19.5V - 29.5V
48V System40.5V - 56.5V
60V System51.5V - 73.5V
72V System62.5V - 88.5V

4.2. Wiring Instructions

  1. Preparation: Ensure the power switch on the inverter is in the "OFF" position.
  2. Connect DC Cables: Connect the provided DC cables securely to the inverter's DC terminals first. Tighten the nuts to prevent overheating from poor contact.
  3. Connect to Battery: Connect the other ends of the cables to the battery (Red to Positive +, Black to Negative -). A small spark may occur when the cables touch the battery terminals due to the internal capacitors charging; this is normal and safe.
Inverter Components and Connections

Figure 3: Diagram showing inverter components including positive and negative terminals, power switch, universal socket, LCD, and cooling fan.

5. Operating Instructions

5.1. Standard Operation Steps

  1. Powering On: Flip the inverter switch to "ON". The inverter will beep briefly for self-testing, and the Green LED (and LCD screen, if applicable) will turn on, indicating AC power is ready.
  2. Connecting Load: Ensure your appliance is turned OFF. Plug the appliance into the inverter's AC socket, then turn the appliance ON.
  3. Powering Off: Turn off the appliance first, unplug it, and then switch the inverter "OFF".

5.2. LCD Screen & Indicator Instructions

Applicable to models with LED indicators and LCD screens:

  • Green Indicator: Normal Operation. The inverter is stably outputting AC power.
  • Red Indicator (with Beeping): Fault Alarm. The protection mechanism has triggered, and the inverter has shut down.
  • LCD Screen: Once powered on, the screen displays real-time data:
    1. Battery Icon: Roughly indicates the remaining battery capacity.
    2. Input DC Voltage (DC V): Shows the real-time battery voltage, helping you determine if the battery is depleted.
    3. Output AC Voltage (AC V): Shows the current AC voltage being output (e.g., 220V or 110V).
Smart LCD Display with Error Codes

Figure 4: Smart LCD display showing input/output voltage, battery status, and potential error codes (Er-1 Low Voltage, Er-2 Input Overvoltage, Er-3 Overheating, Er-4 Overload, Er-5 Output Short-Circuit, Er-6 High-Voltage Rectification Fault).

6. Maintenance

Proper maintenance ensures the longevity and optimal performance of your inverter.

  • Ventilation is Key: Always ensure at least 2 inches (5 cm) of space around the cooling fan for proper airflow. Regularly check that the fan is not obstructed by dust or debris.
  • Avoid Thin Wires: Only use the original high-quality GRENNOVA cables provided with your inverter. Using thinner or substandard wires can lead to overheating and reduced performance.
  • Keep Dry: Avoid any contact with water or high-humidity environments. Moisture can cause short circuits and damage internal components.
  • Cleanliness: Periodically clean the exterior of the inverter with a dry, soft cloth. Do not use liquid cleaners.
  • Terminal Check: Occasionally check that the battery terminal connections are tight to prevent overheating due to loose contacts.

7. Troubleshooting Guide

If you encounter issues with your inverter, refer to the table below for common problems and solutions.

Fault SymptomPossible CauseSolution
Red LED on, Beeping, No AC OutputLow Voltage Protection: Battery depletedCheck if the DC voltage on the screen is below the working range. Recharge the battery immediately.
Over Voltage Protection: Voltage too highEnsure the battery voltage matches the inverter (e.g., do not connect a 12V inverter to a 24V battery).
Overload Protection: Appliance power too highUnplug the overloaded appliance, turn the inverter off, wait 5 seconds, and turn it back on.
Over Temperature: Inverter too hotTurn off the inverter, let it cool for 15 minutes. Ensure it is in a ventilated area and fans are not blocked.
No Response, LEDs offLoose Connection / Blown Fuse1. Check if the battery terminal nuts are tight.
2. If reverse polarity occurred, internal fuses are blown. Contact support.

8. Specifications

This section details the technical specifications for the GRENNOVA Nova Series 2200W Pure Sine Wave Inverter.

FeatureSpecification
Model NumberGRE-N-2200
TypeDC/AC Pure Sine Wave Inverter
Peak Power2200W
Rated Power (Continuous)1100W
Input DC Voltage Options12V, 24V, 48V, 60V (selectable via SKU)
Output AC Voltage Options110V, 220V (selectable via SKU)
Number of Plugs1 (Universal Socket)
Number of USB Ports1
Protection FeaturesAnti-reverse connection, Over-temperature, Over-voltage, Low-voltage, Overload, Short-circuit
Dimensions (L*W*H)26cm * 9.5cm * 5.5cm
CertificationsCE, FCC, RoHS, UL

9. User Tips & FAQ

9.1. User Tips for Longevity

  • Ventilation is Key: Keep at least 2 inches of space around the cooling fan.
  • Avoid Thin Wires: Only use the original high-quality GRENNOVA cables provided.
  • Keep Dry: Avoid any contact with water or high-humidity environments.
  • Power Off When Not in Use: While safe to leave on, turning off the inverter when not in use will conserve battery power.

9.2. Frequently Asked Questions (FAQ)

Q1: Can I use this for my refrigerator or drill?
A: Yes, the Nova series uses Pure Sine Wave technology, compatible with inductive loads like small fridges and drills. Ensure the appliance's starting power doesn't exceed 1100W.
Q2: Why did the wires get hot?
A: This is usually caused by loose terminal screws. Please ensure the alligator clips or ring terminals are tightly fastened to the posts.
Q3: The red light is on, it's beeping, and there is no power. Is it broken?
A: No, the inverter's safety shield has activated. This usually happens for two reasons: 1. Battery is depleted (Low Voltage): Recharge immediately. 2. Overload: The appliance requires more power than the inverter can provide. Unplug it and restart the inverter.
Q4: Can I connect this inverter to the solar controller's "Load" port?
A: NEVER! The inverter draws massive current and will instantly burn out your solar charge controller. Always connect the inverter's cables DIRECTLY to your battery's positive and negative terminals.

10. Warranty & Support

Grennova provides a 12-Month Limited Warranty from the date of purchase. We will repair or replace products with manufacturing defects free of charge during this period.

Disclaimer: The following are NOT covered by warranty:

  • Blown fuses or motherboards caused by reverse polarity connection.
  • Damage caused by connecting the output to the commercial power grid.
  • Water damage or short circuits caused by use in wet/rainy environments.
  • Damage caused by unauthorized disassembly, modification, or force majeure.
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.