1. Setup and Installation
Important: It is strongly recommended to seek professional installation from a qualified car store or personnel.
1.1 Package Contents
- 2 x Dynamic LED Turn Signal Mirror Lights (Left and Right)
1.2 Safety Precautions
- Ensure the vehicle's ignition is off and the battery is disconnected before beginning any electrical work.
- Wear appropriate safety gear, including gloves and eye protection.
1.3 Installation Instructions
These dynamic turn signal lights are designed as a direct replacement for your original car product. The yellow turn signal function is plug-and-play.
Physical Installation:
- Carefully remove the existing rearview mirror indicator light from your vehicle.
- Align and install the new Dynamic LED Turn Signal Mirror Light into the housing.
Electrical Connection (Blue Light Function):
The turn signal is two-colored: yellow for the dynamic turn signal and blue for an accent light. There are three connection methods to achieve the dynamic blue effect, with different results:
- Connect to Puddle Light Power Supply: Connect the positive wire of the blue light to the positive pole of the puddle light power supply. After the car is unlocked or locked, the dynamic blue light will illuminate for 3-10 seconds.
- Connect to Rearview Mirror Flip Power Supply: Connect the positive wire of the blue light to the positive pole of the rearview mirror flip power supply. After the car is unlocked, the dynamic blue light will illuminate for 3-10 seconds.
- Connect to Door Panel Positive Power Wire: Open the door panel and connect the positive wire of the blue light to a positive power wire within the door. After the car is unlocked or locked, or when the turn signal lamp is turned off, the dynamic blue light will illuminate for 3-10 seconds.
Note on Blue Light Connection:
- All buyers are advised to connect the positive wire of the blue light to the normal power from inside the door panel for consistent blue light flow.
- If connected to the positive wire of the electric folding rearview mirror, the blue light may only stream for a second or two when the mirror folds or unfolds, as there will be no continuous current.
- If you prefer not to use the blue light function, you can use tape to insulate the blue light wires or cut them off. The yellow turn signal will function independently.

Figure 1: Wiring Diagram for Yellow and Blue Light Functions
2. Operating Instructions
2.1 Yellow Dynamic Turn Signal
When the vehicle's turn signal is activated, the yellow LEDs will illuminate in a dynamic, sequential flow, providing enhanced visibility for turning or lane changes.
2.2 Blue Accent Light
The blue accent light will activate based on how it is wired during installation:
- If connected to puddle light or mirror flip power: The blue light will illuminate for 3-10 seconds upon unlocking or locking the vehicle, serving as a welcome or accent light.
- If connected to a constant positive power source (e.g., door panel power): The blue light may remain on continuously or activate under specific conditions as per the vehicle's wiring.
Video 1: Demonstration of Dynamic Yellow Turn Signal and Blue Accent Light
3. Maintenance
3.1 Cleaning
To clean the lights, use a soft, damp cloth. Avoid using abrasive cleaners, solvents, or harsh chemicals, as these can damage the plastic housing or LED components.
3.2 Waterproofing
The product is designed to be 100% waterproof, ensuring durability and reliable performance in various weather conditions.

Figure 2: Product Features - Long Lifespan, Safety, and 100% Waterproof
4. Troubleshooting
4.1 Lights Not Working
- Check all electrical connections to ensure they are secure and properly seated.
- Verify that the power source is active and providing the correct voltage (12V).
- Ensure correct polarity for the connections.
4.2 Blue Light Flickering or Not Staying On
- Review the connection method for the blue light. If connected to the electric folding rearview mirror power, it may only activate briefly.
- For consistent blue light operation, ensure it is connected to a stable positive power source within the door panel.
4.3 Dynamic Sequence Not Working
- Check the main plug-and-play connection for the yellow turn signal.
- Ensure there are no loose wires or damaged connectors.
5. Specifications

Figure 3: Product Dimensions
| Feature | Specification |
|---|---|
| Brand Name | Kakulkomen |
| Model Name | Dynamic Blinker Mirror Light |
| Voltage | 12 V |
| Lumens | 2400LM |
| Item Weight | 330g |
| Material Type | Plastic with LED |
| Features | LED Dynamic Side Marker Turn Signal Light |
| Includes | One pair (right and left) |
| Appearance Sign | E8 Mark |
| Waterproof Rating | 100% Waterproof |
| Light Color | Blue / Yellow Dynamic Turn Signals |
| Compatibility | BMW 5 Series F10 F11 F07 Facelift (2014-2016) BMW 6 Series F06 F12 F13 Facelift (2015-2017) BMW 7 Series F01 F02 Facelift (2013-2014) |
6. Warranty and Support
For any warranty claims, technical support, or further assistance, please contact your original seller or retailer. Provide your purchase details and a description of the issue for prompt service.
7. User Tips
- For the most reliable and consistent operation of the blue accent light, it is highly recommended to connect its positive wire to a stable power source directly from the door panel, rather than the electric folding mirror power supply.
- Always double-check all connections before reassembling vehicle components to ensure proper function and avoid rework.
- If you are unsure about any step of the installation process, consult a professional automotive technician.