1. Introduction
This product is a protective accessory designed for motorcycle front fork shock absorption systems. It effectively shields the front fork shock absorber from dust, mud, scratches, and other environmental elements, helping to prolong its lifespan and maintain performance. Made from wear-resistant and waterproof high-elastic fabric, it offers a flexible wrap design for a secure fit.
For detailed instructions and diagrams, you may also refer to the official user manual PDF: User Manual (PDF)
2. Safety & Warnings
General Safety Information
- Installation Requirements: After installation, ensure the sleeve is firmly fixed without loosening. It must not affect the normal telescopic stroke of the shock absorber. Improper installation can lead to potential safety hazards due to displacement during riding.
- Compatibility Warning: This product is only applicable to front shock absorbers with matching dimensions. Do not force installation on front forks of incompatible specifications, as this can impair shock absorption performance.
- Usage Restrictions: This product is an auxiliary protective accessory and cannot replace professional protective gear. Always wear full protective gear during intense off-roading or high-speed riding.
- Damage Replacement: Immediately replace the protective sleeve if it is torn, severely worn, or detached. Do not continue to use a damaged sleeve.
- Children's Warning: Keep this product out of reach of children to prevent risks of accidental ingestion or suffocation.
3. Setup & Installation
Installation Preparation
- Clean the piston rod and oil seal area of the front shock absorber thoroughly to remove sediment, dirt, and oil stains. Ensure the surface is clean and dry.
- Confirm that the length (350mm) and diameter of the protective sleeve are compatible with your front shock absorber. Inspect the sleeve for any damage or deformation before installation.
Installation Procedures
- Stretch open the protective sleeve.
- Fit it over the shock absorber from either the lower or upper end.
- Adjust the position of the sleeve to fully cover the piston rod and oil seal area of the front shock absorber.
- Secure the protective sleeve using the built-in hook-and-loop fastener (velcro) or the provided cable ties. Ensure a tight fit without displacement. The sleeve must not impede the normal expansion and contraction of the shock absorber.
- After securing, press the shock absorber several times to test its smooth expansion and contraction. If there is no jamming or interference, the product is ready for normal use.

Figure 1: Inner view of the protector showing the hook-and-loop closure.

Figure 2: Fork protector installed on a motorcycle's front suspension.
Video 1: Product overview and demonstration of flexibility.
4. Usage
Once properly installed, the front fork protector operates passively, providing continuous protection to your motorcycle's shock absorbers. Ensure the protector remains securely fastened during use. Regularly check its position and condition, especially before and after rides.
5. Maintenance
Care Instructions
- Regular Inspection: Before each ride, check if the protective cover is loose, cracked, or displaced. Adjust or replace it promptly if any abnormality is found.
- Cleaning and Maintenance: Rinse sediment off the surface of the protective cover regularly with clean water. Wipe surface stains with a damp cloth. Allow it to air dry completely before re-installation or storage. Regular cleaning prevents sediment accumulation from wearing the shock absorber oil seal.
- Replacement Cycle: Replace the protective cover with a new one when it loses elasticity, gets torn, or suffers severe wear.
Prohibited Operations
- Do not pierce the protective cover with sharp objects.
- Avoid contact with oil stains, strong acids, strong alkalis, and other corrosive substances.
- Do not bake the cover under high temperatures.
Storage
Store idle protective sleeves in a dry and well-ventilated place. Avoid humid and high-temperature environments to prevent fabric aging and mildew.
6. Troubleshooting
- Protector is loose or displaced: Re-fasten using the hook-and-loop closure or cable ties. If it repeatedly loosens, inspect for wear or damage and consider replacement.
- Protector is torn, cracked, or severely worn: Replace immediately to ensure continued protection.
- Protector does not fit properly: Verify that the dimensions of your motorcycle's front fork match the product specifications (350mm length). Do not force installation on incompatible forks.
- Protector interferes with shock absorber movement: Re-adjust the sleeve's position and tightness. Ensure it is not bunched up or too tight in any area.
7. Specifications
| Feature | Specification |
|---|---|
| Product Name | Motorcycle Front Fork Protector |
| Brand Name | HTBCCHB |
| Material | High elastic waterproof fabric |
| Length | 350mm (35cm) |
| Item Weight | 0.1kg |
| Item Type | Covers & Ornamental Mouldings |
| Protective Parts | Frame Protection, Wheels, Tires & Tubes protection |
| Package Includes | 2 x Front Fork Shock Absorber Protector Sleeves, 2 x Fixed cable ties |
8. User Tips
- Universal Fit: This product is designed for universal fit. While it works for many models (e.g., KTM EXC-F 250 4T, KTM EXC 450), always confirm compatibility with your specific motorcycle's fork dimensions before purchase and installation.
- Covering Imperfections: Users have found this product to be an excellent option for covering rusty or corroded fork bars, improving the aesthetic of the bike.
- Stitching Durability: Some users note that the stitching may not be extremely strong. Handle with care during installation and regular cleaning to prolong the product's life.
- Effective Protection: The protector effectively shields fork rings from dust and mud, performing as expected for basic protection.
9. Warranty & Support
Disclaimer
The manufacturer and seller shall not be held liable for shock absorber malfunctions, riding accidents, personal injury, or property damage caused by:
- Improper installation.
- Use of mismatched shock absorbers.
- Intentional damage.
- Failure to perform regular maintenance as outlined in this manual.
Manufacturer Information
Manufacturer: Yongkang Hongtian Trading Co., Ltd.
Changcheng Village, Yongkang Economic Development Zone, Jinhua City, Zhejiang Province, Room 302, 3rd Floor, No. 66 Jinbi Road, China
EU Authorized Representative: MJCM SARL
78 avenue des Champs Elysees Bureau 326