Introduction
Thank you for choosing the BAOFENG E88/E88 PRO FM two-way radio transceiver. This device is suitable for use in the 446 private mobile radio service (PMR446). It is programmed with 16 PMR446 frequencies, offers a maximum transmission power of 500 mW, and a bandwidth of 12.5 kHz. It features a maximum transmission time limit of 180 seconds and a fixed antenna. No registration or fees are required, though restrictions of use may apply in some Non-EU countries.
ATTENTION!
Before using this product, please read the RF Energy Exposure and Product Safety Guide that ships with the radio. This guide contains instructions for safe usage, RF energy awareness, and control for compliance with applicable standards and regulations.
The BAOFENG E88/E88 PRO is a multi-task PMR446 transceiver, combining the latest radio communication technology with a sturdy mechanical frame. It is an ideal solution for professionals needing to stay in touch with their team (e.g., construction sites, hotels) or for leisure users wanting to connect with friends and family.
Package Contents
The standard package includes the following items:
Standard package contents for Baofeng E88 Walkie Talkie.
- 2 or 4 E88/E88 PRO transceivers (depending on option)
- 2 or 4 1500mAh Li-ion rechargeable battery packs (depending on option)
- 2 or 4 Belt clips (depending on option)
- 2 or 4 Desktop chargers (depending on option)
- 2 or 4 Lanyards (depending on option)
- 2 or 4 User Manuals (depending on option)
- 1 or 2 Boxes (depending on option)
Main Features
Key features of the Baofeng E88 Walkie Talkie.
- 16 PMR446 Channels
- 2 Channels Watch
- Channel Monitor
- 155 Sub-Codes (50 CTCSS codes / 105 DCS codes)
- Hands-Free Operation (VOX)
- Roger Beep Tone
- Battery Level Meter
- Battery/Power Saver
- Low Battery Audible Alert
- 2pin Kenwood headset jack
- Keystroke Tones
- Output power: ≤0.5W
- Sub-Codes Scan and Store
- Channel Scan Function
- 10 Selectable Call Tone Alerts
- Call Alert
- Keypad Lock
- Emergency Strobe Light
- Backlit LCD Display
- TOT (Time out timer)
- Li-Ion 1500mAh battery pack
- Up to 10 km range*
- LED Torch
- Battery Life: up to 18 hours (under typical use conditions)
*Range may vary depending on environmental and/or topographical conditions.
Controls and Parts of the Radio
Diagram of the Baofeng E88/E88 PRO main controls.
- Antenna
- Flashlight
- Volume Knob with Power SW (Power Switch)
- LED indicator: RED - TX (Transmit); GREEN - RX (Receive)
- PTT button (Push-To-Talk)
- LAMP button - Turns the LED flashlight on or off.
- SCAN button - Activates or deactivates scanning.
- Emergency button - Turns emergency alerts on or off.
- Speaker and Built-in microphone
- '+' / '-' buttons: Short press for channel selection. Long press to initiate a ringtone on the current channel.
- 'MENU' button: A short press is used to activate menu functions and confirm settings. Long press is used to lock and unlock function keys.
- Headset jack (Headset not included)
- LCD Display
- 'MON' button: Short press for channel selection. Long press for monitoring (for weak signal monitoring).
- Li-ion Battery pack
Battery Recharge
2-Way Charging Methods: Red indicates charging, Green indicates charging is complete.
The E88/E88 PRO uses a 3.7V Li-ion rechargeable battery pack. To recharge, connect the AC/DC wall adaptor to a mains power socket and insert the adaptor's jack into the desktop charger plug. A full recharge takes approximately 4-5 hours.
For maximum battery life, it is recommended to charge the battery pack when the E88/E88 PRO is off and the battery is fully discharged.
WARNING: Using a different battery charger other than the one specified can cause damage to your device or may even cause explosions and personal injuries.
Basic Operations
To get the most out of your new radio, please read this guide completely before operating the unit.
Power On/Off and Volume Adjustment
Rotate the Power/Volume knob clockwise to turn the radio on. Continue rotating clockwise to increase the volume. To adjust the volume level, rotate the control clockwise or counter-clockwise as preferred. To turn the radio off, rotate the control counter-clockwise until you hear a mechanical "click".
Choosing a Channel
Your radio has 16 channels and 155 Sub-Codes. To communicate with others, both radios must be set to the same channel and Privacy code.
If the channel selection buttons (+ or MON) are locked, press and hold the MENU button for 2 seconds to unlock. Then press the + or MON buttons to select one of the 16 PMR channels.
Keypad Lock
To prevent accidental changes to radio settings, press the MENU button for 2 seconds. A lock icon will appear on the display. The PTT, +, and MON keys will remain active. Repeat the procedure to unlock the keypad.
Talking on Your Radio
- Press and hold the [PTT] button. Speak in a clear, normal voice about 2-3 inches away from the microphone. The TX arrow icon will appear on the display. Pause briefly after pressing the [PTT] button before speaking to avoid cutting off the beginning of your transmission.
- When finished speaking, release the [PTT] button. The RX arrow icon will display, indicating you can receive incoming calls.
Monitor Mode Feature
This feature allows you to listen for weak signals on the current channel. To activate, press and hold the MON button for 2 seconds until two beeps sound. The receiver circuit will stay open, allowing both noise and weak signals to be heard. The RX icon will blink. To deactivate, press and hold the MON button for 2 seconds again; two beeps will sound, and the RX icon will disappear.
Channel Scanning
Your radio can scan all 16 channels for activity. To enter scan mode, quickly press the SCAN button. Repeat the same procedure to exit.
The radio will rapidly scan channels and stop on any active channel. It will resume scanning after 5 seconds if the channel becomes inactive. If you press the [PTT] button to transmit on an active channel, scanning will stop and remain on that channel for 10 seconds before resuming scan when [PTT] is no longer pressed. To resume scanning manually, quickly press the SCAN or MON button.
Scanning Sub-Codes
Press and hold the SCAN button to enter Sub-Codes scanning. A flashing "CTC/DCS" will appear on the left status display. The lower display will cycle through Sub-Codes being tested. Once a Privacy code is determined, the "CTC/DCS" indicator will stop flashing. Press the [PTT] button to save the scanned tone into memory.
Using the Flashlight
The integrated LED flashlight provides illumination in dark environments.
You can use the integrated LED flashlight for illumination. Press the LAMP button once to turn the flashlight on continuously. Press it again to activate the strobe emergency mode (flashing light). Press it a third time to turn the light off.
Emergency Alert Function
The walkie talkie makes loud sirens and flashing red light when turned on to alert others to your location.
The Emergency Alert feature can be used to signal group members for help. To activate, press and hold the [Emergency] button on the top for 3 seconds. The radio will emit a loud siren sound and the flashlight will flash. Press the [Emergency] button again to exit the function.
WARNING: The Emergency Alert feature should only be used in the event of an actual emergency.
CTCSS/DCS Tones Selection
The BAOFENG E88/E88 PRO can receive in two modes: Open traffic (hear all communication) or Group mode CTCSS/DCS (hear only messages with the same channel and code).
To activate one of 50 different CTCSS/105 DCS tones for RX and TX:
- Turn on the radio.
- Select the desired channel.
- Press the MENU button once until "oF" (blinking) appears on the display.
- By pushing the + or MON button, the display will show CTCSS (ct blinking) or DCS (dc blinking). Press MENU to enter the CTCSS or DCS tones. Select the desired tone with the + or MON buttons.
- Press the PTT button to exit the menu or MENU to continue setup.
VOX Function (Hands-Free Operation)
The BAOFENG E88/E88 PRO enables hands-free conversations through its VOX function.
- To activate VOX, press the MENU button 3 times until 'VOX' appears on the display.
- Use the + or MON buttons to select the desired sensitivity level (1: high, 2: medium, 3: low).
- Press the PTT button to exit the menu or MENU to continue setup.
To disable VOX, follow the same steps and select option 'oF' (OFF).
Setting and Transmitting Call Tones
The BAOFENG E88/E88 PRO can transmit 10 different call tones to alert other radios in your group.
- To select a call tone, press the MENU button 4 times until "CA" appears on the display.
- Use the + or MON buttons to preview the call tones.
- Press the PTT button to exit the menu or MENU to continue setup.
To transmit your selected call tone, set your radio to the same channel and Sub-Code as the receiving radios, then press and hold the + button.
Keypad Beep
To deactivate the keypad beep:
- Press the MENU button 6 times until "bP on" is displayed.
- Use the + or MON buttons until the display shows "bP oF".
- Press the PTT button to exit the menu or MENU to continue setup.
ROGER BEEP (End Transmission Tone)
When your transmission ends (PTT released), the BAOFENG E88/E88 PRO emits a tone indicating to the other party that they can begin speaking. This function is enabled by default.
To deactivate it:
- Press the MENU button 7 times until the display shows "rb on".
- Use the + or MON buttons to select "oF" and "rb oF" will be displayed.
- Press the PTT button to exit the menu or MENU to continue setup.
Dual Watch Mode
Your radio has a DUAL WATCH function, allowing you to scan 2 channels for activity. The first channel will be your current setting, and the second will be a selected channel.
To set another channel and start Dual Watch:
- Press the MENU button 8 times until the display shows "oF du".
- Use the + or MON buttons to select the channel, then press MENU.
- Use the + or MON buttons to select the CTCSS/DCS, then press MENU.
- The radio will start Dual Watch, alternating between the home channel and the Dual Channel Monitor channel.
To end Dual Watch mode, press the SCAN button.
Note: Dual Watch mode will not function if you set the same channel and Sub-code as the current channel.
Maintenance
Your E88/E88 PRO is designed for long-term use. Please follow these suggestions:
- Do not attempt to open the unit. Non-expert handling may damage it and/or void the warranty.
- When using a regulated power supply, ensure the power voltage is 5V to avoid damage.
- High temperatures can shorten the life of electronic devices and warp or melt plastics.
- Do not store the radio in dusty or dirty areas.
- Keep the radio dry. Rainwater or dampness can corrode electronic circuits.
- If the radio emits a peculiar smell or smoke, immediately turn off its power and remove the charger or battery.
- Do not transmit without an antenna.
Specifications
Physical dimensions of the Baofeng E88/E88 PRO.
General
| Attribute | Value |
|---|---|
| Frequency Range | UHF 400-470MHz (PMR446) |
| Channels | 16 PMR446 |
| Working Temperature | -10°C to +50°C |
| Operation Voltage | DC 3.7V ±10% |
| Operation Mode | Simplex |
| Dimensions | 115mm x 60mm x 33mm (without Antenna) |
| Weight | 150g (Battery pack included) |
| Antenna Impedance | 50ohm |
| Category | B |
Transmitter
| Attribute | Value |
|---|---|
| Frequency Stability | ±2.5ppm |
| RF Output Power | ≤500mW ERP |
| Max Frequency Deviation | ≤2.5KHz |
| Audio Distortion | <3% |
| Adjacent Channel Power | <60dB |
Receiver
| Attribute | Value |
|---|---|
| Receive Sensitivity | <0.2µV @20dB SINAD |
| Audio Distortion | <3% |
| Audio Response | 300Hz~3KHz |
Frequency Chart
| Ch. | Freq. (MHz) | Ch. | Freq. (MHz) | Ch. | Freq. (MHz) | Ch. | Freq. (MHz) |
|---|---|---|---|---|---|---|---|
| 1 | 446.00625 | 5 | 446.05625 | 9 | 446.10625 | 13 | 446.15625 |
| 2 | 446.01875 | 6 | 446.06875 | 10 | 446.11875 | 14 | 446.16875 |
| 3 | 446.03125 | 7 | 446.08125 | 11 | 446.13125 | 15 | 446.18125 |
| 4 | 446.04375 | 8 | 446.09375 | 12 | 446.14375 | 16 | 446.19375 |
User Tips
- Maximize Range: For best coverage, use the walkie talkie in open spaces with minimal obstructions. In urban areas, expect 1-2 km; in open areas with some obstacles, 4-6 km; in clear line-of-sight, up to 10 km.
- Battery Life: To prolong battery life, ensure the radio is turned off and the battery is fully discharged before recharging.
- Clear Communication: When transmitting, hold the PTT button firmly and speak clearly about 2-3 inches from the microphone. Pause slightly after pressing PTT before speaking to ensure your message isn't cut off.
- Monitor Weak Signals: Use the Monitor Mode feature (long press MON button) to temporarily open the squelch and listen for very weak signals that might otherwise be filtered out.
- Hands-Free Use: Activate the VOX function for hands-free communication, especially useful when your hands are occupied. Adjust sensitivity (Level 1 for quiet, Level 3 for noisy environments) as needed.
- Emergency Use: The Emergency Alert function is designed for critical situations to signal for help. Use it responsibly.
Warranty & Support
Your E88/E88 PRO is designed to meet warranty obligations and provide years of enjoyment. For any warranty-related inquiries or support, please contact the seller or your local Baofeng helpdesk.
EU Declaration of Conformity: Baofeng and Pofung declare that this radio equipment complies with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at: http://www.pofung.cn/download.asp?EnBigClassName=EU%20DOC. You can also contact wangjianhui@baofengradio.com for support.
EU Contact: APEX CE SPECIALISTS LIMITED, Unit 3D North Point House, North Point Business Park, New Mallow Road, Cork, T23 AT2P, Ireland.
Manufacturer: PO FUNG ELECTRONIC (HK) INTERNATIONAL GROUP COMPANY LIMITED, Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong. Website: http://www.pofungshop.com.