Baofeng UV-G30 PRO Two-Way Radio User Manual
Model: UV-G30 Pro
Brand: BAOFENG
1. Getting Started
1.1 Regulations and Safety Warnings
Thank you for purchasing this product, which is a dual band/dual display/dual watch radio. This easy-to-use radio will deliver secure, instant, and reliable communications at peak efficiency. Please read this manual carefully before use to derive maximum performance from your radio.
WARNING!
European Users should note that operation of this unit in Transmit mode requires the operator to have a valid Amateur Radio License from their respective Countries Amateur Radio Licensing Authority for the Frequencies and Transmitter Power levels that this Radio transmits on. Failure to comply may be unlawful and liable for prosecution. Refer to the "EU" specification guide 2014/53/EU.
ATTENTION!
When programming the radio, start by reading the factory software data, and then rewrite this data with your frequency etc., to a new saved code plug, otherwise errors may occur. You can use the programming cable with a PC to program the authorized frequency, bandwidth, power, etc. Your programming must comply with your FCC (or EU other country) license certification.
ATTENTION!
Before using this product, read the RF Energy Exposure and Product Safety Guide that ships with the radio, which contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulation.
PMR446, FRS, GMRS, MURS
You may be tempted to use PMR446 (in Europe) or FRS, GMRS, MURS (in the USA) frequencies. Do note however that there are restrictions on these bands that make this transceiver illegal for use.
Precautions for Portable Terminals
Operating Prohibitions
- Do not operate the product in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials. Only an approved Ex-protection model is allowed for use in such locations; any attempt to assemble or disassemble it is strictly prohibited.
- Do not operate the product near or in any blasting area.
- Do not operate the product near any medical or electronic equipment that is vulnerable to RF signals.
- Do not hold the product while driving.
- Do not operate the product in any area where use of wireless communication equipment is completely prohibited.
Important Tips
- Do not use any unauthorized or damaged accessory.
- Keep the product at least 2.5 centimeters away from your body during transmission.
- Do not keep the product receiving at high volume for a long time.
- For vehicles with an air bag, do not place the product in the area over the air bag or in the air bag deployment area.
- Keep the product and its accessories out of reach of children and pets.
- Please operate the product within the specified temperature range.
- Continuous transmission for a long time may lead to heat accumulation within the product. In this case, please keep it at a proper location for cooling.
- Handle the product with care.
- Do not disassemble, modify or repair the product and its accessories without authorization.
Precautions for Batteries
Charging Prohibitions
- Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials.
- Do not charge your battery that is wet. Please dry it with a soft and clean cloth prior to charge.
- Do not charge your battery suffering deformation, leakage, and overheat.
- Do not charge your battery with an unauthorized charger.
- Do not charge your battery in a location where strong radiation is present.
- Overcharge shall always be prohibited as it may shorten the life of your battery.
2. Setup
2.1 Content of the Packaging
The package includes:
- 1 Radio
- 1 Fast desktop charger
- 1 Antenna
- 1 Li-Ion battery pack
- 1 Belt clip
- 2 NA-771 Antennas (for 2-pack)
- 2 Standard Earphones (for 2-pack)
- 2 User Manuals (for 2-pack)
- 2 Lanyards (for 2-pack)
- 2 Type-C Cables (for 2-pack)
- 2 Clips (for 2-pack)
- 2 Boxes (for 2-pack)
- 2 Batteries (for 2-pack)
If any item is missing, please verify with your dealer.

Image: Package contents for Baofeng UV-G30 PRO 2-pack, including two radios and all accessories.
2.2 Charging the Battery
2.2.1 Charging the Battery Pack
The Li-ion battery pack is not charged at the factory; please charge it before use. For optimal performance, fully charge/discharge the battery two or three times before regular use. The battery pack life may be depleted when its operating time decreases even after being fully charged; in this case, replace the battery pack.
2.2.2 Charger Supplied
Please use the specified charger provided by our company. Other models may cause explosion and personal injury. After installing the battery pack, and if the radio displays low battery with a voice prompt, please charge the battery.
2.2.3 Use Caution with the Li-ion Battery
- Do not short the battery terminals or throw the battery into a fire. Never attempt to remove the casing from the battery pack.
- The ambient temperature should be between 5°C-40°C (40°F-105°F) while charging the battery. Charging outside this range may not fully charge the battery.
- Please turn off the radio before inserting it into the charger. It may otherwise interfere with correct charging.
- To avoid interfering with the charging cycle, please do not cut off the power or remove the battery during charging until the green light is on.
- Do not recharge the battery pack if it is fully charged. This may shorten the life of the battery pack or damage the battery pack.
- Do not charge the battery or the radio if it is damp. Dry it before charging to avoid damage.
WARNING!
When keys, ornamental chain, or other electric metals contact the battery terminal, the battery may become damaged or injure a human. If the battery terminals are short-circuited, it will generate a lot of heat. Take care when carrying and using the battery. Remember to put the battery or radio into an insulated container. Do not put it into a metal container.
2.2.4 How to Charge
- Plug the AC adaptor into the AC outlet, and then plug the cable of the AC adaptor into the DC jack located on the back of the charger. The indicator light blinks orange and is then ready to charge a battery.
- Plug the battery or the radio into the charger. Make sure the battery terminals are in good contact with charging terminals. The indicator light turns red—charging begins.
- It takes approximately 2-5 hours to fully charge the battery. When the lamp lights green, the charging is completed. Remove the battery or the radio unit with its battery from the socket.
When charging a radio (with battery), the indicating lamp will not turn green to show the fully charged status if the radio is powered on. Only when the radio is switched off will the lamp indicate normal operation. The radio consumes energy when it is powered on, and the charger cannot detect the correct battery voltage when the battery has been fully charged. So the charger will charge the battery in constant voltage mode and fail to indicate correctly when the battery has been fully charged.
2.2.5 LED Indicator
| STATUS | LED |
|---|---|
| No Battery | Green and red alternately flashing |
| Charge Normally | Red |
| Fully Charged | Green |
| Trouble | Red blinks fast for a long time |
NOTE:
Trouble means battery too warm, battery short-circuited, or charger short-circuited.
2.2.6 How to Store the Battery
- If the battery needs to be stored, keep it in a state of 80% discharged.
- It should be kept in a low temperature and dry environment.
- Keep it away from hot places and direct sunlight.
- Do not short circuit the battery terminals.
- Never attempt to remove the casing from the battery pack.
- Never store the battery in unsafe surroundings, as a short may cause an explosion.
- Do not put the battery in a hot environment or throw it into a fire, as it may cause an explosion.
2.2.7 Using the Type-C USB Charger
The micro-USB charger is a handy port that allows you to conveniently charge your Li-ion battery pack.
- Make sure your radio is turned OFF.
- Plug the Type-C USB cable into the Type-C USB charging port on your battery. Connect the other end of the micro-USB charger to a wall power outlet.
- An empty battery will be fully charged in 4 hours.
- The battery meter on the LCD will move to indicate the battery is charging.

Image: Type-C charging port on the Baofeng UV-G30 PRO radio, illustrating various charging methods.
Note:
- It is recommended to power OFF your radio while charging. However, if power is turned on while charging, you may not be able to transmit a message if the battery is completely empty. Allow time for the battery to charge to 1 bar before attempting to transmit a message.
- For optimal battery life, remove the radio from the charger within 6 hours. Do not store the radio while connected to the charger.
2.3 Installation of Accessories
Before the radio is ready for use, we need to attach the battery pack, as well as charge the battery.
2.3.1 Installing / Removing the Antenna
- Installing the Antenna: Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure.
- Removing the Antenna: Turn the antenna counter-clockwise to remove it.
2.3.2 Installing the Belt Clip
- At the back of the radio, there are two parallel screws mounted above the battery. Remove these and thread them through the holes on the belt clip as you screw them back into the radio body.
- Removing the Belt Clip: Unscrew counter-clockwise to remove the belt clip.
2.3.3 Installing the Battery Pack
Before attaching or removing the battery, make sure your radio is turned off by turning the power/volume knob all the way counter-clockwise.
- Make sure the battery is aligned in parallel with the radio body with the lower edge of the battery about 1-2cm below the edge of the radio.
- Once aligned with the guide-rails, slide the battery upward until you hear a click as the battery locks in place.
Removing the Battery Pack
To remove the battery, press the battery release above the battery pack, as you slide the battery downward.
2.3.4 Installing the Additional Speaker/Microphone (Optional)
Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack.
3. Operating Your Radio
3.1 Radio Overview
3.1.1 Buttons and Controls of the Radio

Image: Detailed diagram of the Baofeng UV-G30 PRO radio, highlighting its various buttons and controls.
- Antenna
- SK1- Flashlight/Emergency key
- PTT key
- SK2- FM broadcast/Monitor key
- Power/Volume knob
- LED flashlight
- Color LCD
- MENU Key
- Numeric keypad
- MIC Input
- EXIT Key
- Up/Down navigation keys
- TX/RX Status LED
- Accessory jack
- Type-C charging indicator
- Type-C charging port
- Battery tightening screw
3.1.2 LCD Display
| Icon | Description |
|---|---|
| RSSI | Squelch Open/Close Indicator |
| H/L | Transmit power level indicator (High/Low) |
| ♪ | DTMF side tone from radio speaker (set to DT-ST, ANI-ST, DT+ANI) |
| D | DCS enabled |
| C | CTCSS enabled |
| + | Enables access of repeaters in VFO/Frequency Mode. TX will be shifted higher in frequency than RX. |
| - | Enables access of repeaters in VFO/Frequency Mode. TX will be shifted lower in frequency than RX. |
| D | Dual watch enabled |
| 🔒 | Keypad lock enabled |
| VOX | VOX enabled |
| 📞 | Confidential calling feature activated |
| N | Narrowband enabled |
| 🔋 | Battery level indicator |
| R | Reverse function enabled |
| ▶ | Indicates active band or channel |
Battery Level Indicator
When the battery level indicator reads 🔋, the battery is depleted. At this point, the radio will start beeping periodically, flash the backlight of the display, and if voice prompts are enabled, a "Low Voltage" announcement will be heard, indicating that you need to change your battery or put your radio in the charger.
3.1.3 Status Indications
The status LED has a very simple and traditional design:
| LED Indicator | Radio Status |
|---|---|
| Constant Red | Transmitting |
| Constant Green | Receiving |
3.1.4 Main Keypad Controls
- Side key 1 (Flashlight and Alarm): Press [SK1] momentarily to turn on the LED flashlight. Another momentary press will flash the LED. Another momentary press turns the flashlight off. Press and hold [SK1] to activate the alarm function. Press [SK1] (a short press) again to turn it off.
- Side key 2 (Broadcast FM and Monitor): Press [SK2] momentarily to start the broadcast FM receiver. Another momentary press turns the broadcast FM receiver off. If a signal is received on the active frequency or channel while listening to broadcast FM, the receiver will open squelch to that frequency (as if scanning) and remain there until the signal goes away; it will then switch back to broadcast FM. Press and hold [SK2] to monitor the signal, which opens the squelch to listen to the unfiltered signal.
- MENU Key: Used for activating the MENU, choosing each MENU selection, and confirming the parameter. In standby mode, press and hold the key to switch between frequency (VFO) mode and channel (MR) mode. To save frequencies to channel memory, you must be in Frequency (VFO) mode.
- Up (▲) Key: Press it for more than 2 seconds, the channel and frequency will move upwards rapidly; in SCAN mode, press this control to move the scanning upwards.
- Down (▼) Key: Keep it pressed for more than 2 seconds, the channel and frequency will move downwards rapidly; in SCAN mode, press this control to move the scanning downwards.
- EXIT Key: Press to exit the Menu and functions. A/B (appears on the display): press to select the desired frequency (VHF or UHF) in the main or secondary display. Press and hold the EXIT key to activate the one-touch search function.
- Numeric Keypad: Used to input information or selections. In transmit mode, press number keys to send a corresponding DTMF code.
- Star (*) Key: A short momentary press enables the reverse function. Pressing this key for more than 2 seconds will lock/unlock the keypad.
- Pound (#) Key: Press the # key to activate the DTMF dial function. Press and hold the # key to activate the channel scan or frequency scan function. In FM radio mode, press the # key to automatically search for broadcast programs.
- 0 Key (SQL): Press and hold the [0SQL] key to activate the NOAA weather forecast reception function.
3.2 Basic Operations
3.2.1 Power On/Off the Radio
- Turning the unit on: Rotate the Volume/Power knob clockwise until you hear a "click". The display will show a message or flash the LCD depending on settings. If Voice prompt is enabled, it will announce "frequency mode" or "channel mode".
- Turning the unit off: Rotate the Volume/Power knob counter-clockwise until you hear a "click". The unit is now off.
3.2.2 Adjusting the Volume
To turn up the volume, turn the Volume/Power knob clockwise. To turn the volume down, turn the Volume/Power knob counter-clockwise. Be careful not to turn it too far, as you may inadvertently turn your radio off. Using the monitor function (enabled from the [FM broadcast/Monitor] key below the PTT) can help adjust your volume by listening to the un-squelched static.
3.2.3 Main Band/Sub Band Select
In standby mode, press the A/B key to switch between A (upper) and B (lower) displays. The frequency or channel on the selected display becomes the active listening and transmit frequency or channel. To save frequencies to channel memory, you must be on the A display.
3.2.4 VFO/Channel Switch
Press and hold the VFO/MR key to switch between VFO and channel display.
- In channel mode (MR), the channel number will be displayed on the right.
- In frequency mode (VFO), 'VFO' will be displayed on the right.
3.2.5 Frequency (VFO) Mode
In Frequency (VFO) mode, you can navigate up and down the band using the ▲ or ▼ keys. Each press will increment or decrement your frequency according to the frequency step you've set. You can also input frequencies directly on your numeric keypad with kilohertz accuracy.
Example: Entering the frequency 436.61250 MHz on display A
- In standby mode, press and hold the VFO/MR key to switch to the frequency (VFO) mode.
- Enter [4][3][6][6][1][2][5][0] on the numeric keypad.
WARNING!
Just because you can program in a channel does not mean you're automatically authorized to use that frequency. Transmitting on frequencies you're not authorized to operate on is illegal, and in most jurisdictions a serious offense. However, it is legal in most jurisdictions to listen. Contact your local regulatory body for further information on what laws, rules, and regulations apply to your area.
3.2.6 Channel (MR) Mode and Channel Selection
There are two modes of operation: Frequency (VFO) mode and Channel or Memory (MR) mode. For everyday use, Channel (MR) mode is more practical. Frequency (VFO) mode is useful for experimentation and programming channels into memory.
In Channel (MR) mode, you can navigate up and down the channel using the ▲ or ▼ keys or the encoder. Press and hold the VFO/MR key to switch the radio between VFO and Channel mode, select Channel mode.
- Operation 1: Press the ▲ or ▼ navigation key to select the channel.
- Operation 2: Input the channel numbers by the keyboard. For example, to switch to channel 12, input [0][1][2].
When the voice prompt function is enabled, the corresponding channel will be broadcast by voice.
3.2.7 Making a Call
NOTE: Press the A/B key to switch the main channel to the other channel if two channels are shown on the display. In standby mode, press and hold the VFO/MR key to switch between frequency (VFO) mode and channel (MR) mode.
- Channel mode call: After selecting a channel, hold down the [PTT] key to initiate a call. Speak into the microphone with a normal tone. The red LED will be on during transmission.
- Frequency mode call: Press and hold the VFO/MR key to switch to frequency mode, input the working frequency, and press and hold the [PTT] key to transmit. The red LED will be on during transmission.
- Receive a call: When you release the [PTT] key, you can answer without any action. The green LED will be on when receiving a call.
NOTE: To ensure the best reception volume, keep the distance between the microphone and your mouth between 2.5 cm and 5 cm during transmission.
3.2.8 Using the Flashlight
You can use this radio's high-intensity LED flashlight in an emergency by pressing the [SK1] key.

Image: The Baofeng UV-G30 PRO's high-brightness flashlight, useful for outdoor activities in dark environments.
- Press [SK1] once for continuous light (Always On mode).
- Press [SK1] again for strobe light (Strobe emergency mode).
- Press [SK1] a third time to turn the light off.
3.2.9 Emergency Alert
The Emergency Alert feature can be used to signal members in your group for help. To activate, press and hold the [SK1] key for 3 seconds. The radio will send a loud siren sound and the flashlight will flash. Press [SK1] to exit the emergency alert function.
WARNING!
The Emergency Alert feature should only be used in the event of an actual emergency.
3.2.10 FM Radio (FM)
The frequency range for listening to the radio is 65-108MHz. When listening to broadcast FM, press the A/B key to switch between 65-75 MHz and 76-108 MHz bands.
- In frequency or channel mode, press [SK2] to turn on the radio.
- Select the desired radio frequency with the ▲ or ▼ keys or input the frequency. Alternatively, press # to automatically search for a radio station.
- Press [SK2] to exit FM radio.
Note: While listening to the radio, if the frequency or channel of an A/B receiving signal is detected, the radio will automatically switch to that frequency/channel mode for normal transmitting and receiving. When the signal disappears, the radio will automatically switch back to FM radio mode.
3.2.11 Monitor
In standby, press and hold the [SK2] key to enter Monitor. This function allows you to monitor weak signals or signals with unmatched carriers/signaling. Stop pressing [SK2] to turn off the speakers and return to standby mode.
Note: If no signal is present, pressing [SK2] will emit noise.
3.2.12 Keypad Lock
The radio features a keypad lock that locks out all keys except for the three side keys. To enable or disable the keypad lock, press and hold the * key for about two seconds. You can also enable automatic keypad lock after ten seconds from the menu.
3.2.13 Frequency Reversal
A short momentary press of the * key enables the reverse function. If you want to listen to the repeater's input frequency instead, press the * key momentarily, and you'll reverse your transmit and receive frequencies. This is indicated by an "R" in the top row of the LCD, next to the + and - for the offset direction.
3.2.14 TX Repeaters Tone
Press [PTT] + [SK2] key to send a 1750Hz repeater tone. This function is useful for communications through repeaters. If the keypad lock is enabled, you can still send a 1750Hz tone without unlocking the radio.
3.2.15 One Touch Frequency Search
- The radio will act as a receiver. Press and hold the EXIT key, and the screen will display "SEARCH SEARCH...".
- If the transmitter continues to transmit and the unit receives an effective frequency (the strongest and stable signal), the received frequency will be displayed. If there is a CTCSS or DCS, the CTCSS or DCS value is displayed; if none, "NONE" is displayed.
- You can press the MENU key to save the Search frequency and CTCSS or DCS to the channel.
Note: During frequency Search, press the # key on the radio to switch between UHF or VHF bands.

Image: Frequency Measurement Function, allowing fast copying of frequencies and CTCSS from other devices.
3.2.16 Weather Radio/Scan Weather Channel (NOAA)
Your radio has a NOAA Weather Radio function to receive weather reports from designated NOAA stations. It also has a NOAA Weather Scan function to scan all 10 channels of the NOAA Weather Radio.

Image: Baofeng UV-G30 PRO displaying NOAA weather channel, highlighting its 10 NOAA Weather Channels feature.
- To turn the NOAA Weather Scan on, press and hold the [0SQL] key for 3 seconds. A cloud icon appears, and the radio will go to Weather band mode.
- Press and hold the # key for 3 seconds to start automatic scanning of all 10 channels and stop on active channels. Pressing and holding the # key for 3 seconds during a NOAA weather scan will stop the scan.
- After stopping NOAA weather scan, you can manually select the weather channel by pressing the ▲ or ▼ key.
- To exit the Weather Radio broadcast mode, press the MENU key or [PTT] key.
Weather Channel Frequencies and Names
| Channel Number | RX Frequency MHz | Channel Number | RX Frequency MHz |
|---|---|---|---|
| Wx-01 | 162.550 | Wx-06 | 162.500 |
| Wx-02 | 162.400 | Wx-07 | 162.525 |
| Wx-03 | 162.475 | Wx-08 | 161.650 |
| Wx-04 | 162.425 | Wx-09 | 161.775 |
| Wx-05 | 162.450 | Wx-10 | 163.275 |
NOTE: Weather Channels Wx 1 Thru 10 are receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.
3.3 Advanced Features
3.3.1 Working the Menu System
For a complete reference on available menu items and parameters, see Appendix B, Menu definitions. If your radio is set to Memory (MR) mode, the following menu items will not take any effect: STEP, TXP, W/N, CTCSS, DCS, S-CODE, PTT-ID, BCL, SFT-D, OFFSET, MEM-CH.
Basic Use with Arrow Keys
- Press the MENU key to enter the menu.
- Use the ▲/▼ keys to navigate between menu items.
- Once you find the desired menu item, press MENU again to select that menu item.
- Use the ▲/▼ keys to select the desired parameter.
- When you've selected the parameter you want to set:
- To confirm your selection, press MENU, and it will save your setting and bring you back to the main menu.
- To cancel your changes, press EXIT, and it will reset that menu item and bring you out of the menu entirely.
- To exit the menu at any time, press EXIT.
Using Shortcuts
Every menu item has a numerical value. These numbers can be used for direct access. The menu is also organized so that the ten most common functions are on top. The parameters also have a number associated with them.
Using the Menu with Shortcuts
- Press the MENU key to enter the menu.
- Use the numerical keypad to enter the number of the menu item.
- To enter the menu item, press the MENU key.
- For entering the desired parameter, you have two options:
- Use the arrow keys as described above; or
- Use the numerical keypad to enter the numerical shortcut code.
- To confirm your selection, press MENU, and it will save your setting and bring you back to the main menu.
- To cancel your changes, press EXIT, and it will reset that menu item and bring you out of the menu entirely.
- To exit the menu at any time, press EXIT.
- All further examples and procedures in this manual will use the numerical menu shortcuts.
3.3.2 Scanning
The radio features a built-in scanner for VHF and UHF bands. In Frequency (VFO) mode, it will scan in steps according to your set frequency step. In Channel (MR) mode, it will scan your channels. Dual Watch is inhibited while scanning. To enable the scanner, press and hold the # key for about two seconds. Press and hold the # key to exit scanning mode.
Scanning Modes
The scanner is configurable to one of three ways of operation: Time, Carrier, or Search.
- Time Operation (TO): The scanner stops when it detects a signal, and after a factory preset timeout, it resumes scanning.
- Carrier Operation (CO): The scanner stops when it detects a signal, and after a factory preset time with no signal, it resumes scanning.
- Search Operation (SE): The scanner stops when it detects a signal. To resume scanning, you must press and hold the # key again.
Setting Scanner Mode
- Press the MENU key to enter the menu.
- Enter 21 on your numeric keypad to access scanner mode.
- Press the MENU key to select.
- Use the UP and DOWN keys to select the scanning mode.
- Press the MENU key to confirm and save.
- Press the EXIT key to exit the menu.
Frequency Scanning
- In frequency mode, press # for more than 2 seconds. The radio will start scanning the frequency according to the set frequency step.
- You can change the scanning direction with the ▲/▼ keys.
- Press # to stop the scanning.
Note: For Scan mode, see Menu No.21.
Channel Scanning
- In channels mode, press # for more than 2 seconds. The radio will start scanning according to the channel you set.
- You can change the scanning direction with the ▲/▼ keys.
- Press # to stop scanning.
Note: For Scan mode, see Menu No.21.
Scan CTCSS
This function allows scanning frequencies with CTCSS tone enabled.
- In standby mode, press [1][4]; "Scan CTCSS" will appear on the display.
- Press MENU, and the scan of CTCSS tones will start.
NOTES: The function cannot be activated when the radio is set in Channel mode. The Scan will start only when the receiving band detects a signal.
Scan DCS
This function allows scanning frequencies with DCS code enabled.
- In standby mode, press [1][5]; the display will show "Scan DCS".
- Press MENU, and the scan of DCS codes will start.
NOTES: The function cannot be activated when the radio is set in Channel mode. The Scan will start only when the receiving band detects a signal.
3.3.3 Manual Programming (Channels Memory)
Memory channels are an easy way to store commonly used frequencies. The radio features 999 memory channels, each capable of holding: Receive and transmit frequencies, transmit power, group signaling information, bandwidth, ANI/PTT-ID settings, and a six-character alphanumeric identifier or channel name.
Frequency Mode vs. Channel Mode
In standby mode, press and hold the VFO/MR key to switch between frequency (VFO) mode and channel (MR) mode. These two modes have different functions:
- Frequency Mode (VFO): Used for temporary frequency assignments, such as a test frequency or quick field programming if permitted.
- Channel Mode (MR): Used for selecting preprogrammed channels.
Example 1: Programming a Channel Repeater Offset with CTCSS Tone
EXAMPLE: New memory in Channel 10:
- RX = 432.55000 MHz
- TX = 437.55000 MHz (This is a (+ 5) Offset)
- TX CTCSS tone 123.0
- Press the MENU key to switch between menus.
- Press and hold the VFO/MR key to set the radio to VFO mode, and the VFO icon is displayed on the right.
- [3][1] MENU [1][0] (Deletes Prior Data in channel 10)
- [1][2] MENU 123.0 (Selects desired TX encode tone)
- Use ▲/▼ to select Upper display.
- Enter RX frequency (Ex. 43255000).
- [3][0] MENU [1][0] (Enter the desired channel 10, RX has been added)
- Enter TX frequency (Ex. 43755000).
- [3][0] MENU [1][0] (Enter the same channel 10, TX has been added)
- Press and hold the VFO/MR key to return to the MR mode, and the channel number will reappear.
Example 2: Programming a Simplex Channel with CTCSS Tone
EXAMPLE: New memory in Channel 10:
- RX = 432.6625 MHz
- TX CTCSS tone 123.0
- Press the MENU key to switch between menus.
- Press and hold the VFO/MR key to set the radio to VFO mode, and the VFO icon is displayed on the right.
- [3][1] MENU [1][0] (Deletes Prior Data in channel 10)
- [1][2] MENU 123.0 (Select desired TX encode tone 123 CTCSS)
- Use ▲/▼ to select Upper display.
- Enter RX frequency (Ex. 43266250).
- [3][0] MENU [1][0] (Enter the desired channel 10, Channel has been added)
- Press and hold the VFO/MR key to return to the MR mode, and the channel number will reappear.
3.3.4 Repeaters Programming
The following instructions assume that you know what transmit and receive frequencies your repeater employs, and that you're authorized to use it.
- Press and hold the VFO/MR key to set the radio to VFO mode, and the VFO icon is displayed on the right.
- Use the numeric keypad to enter the repeater's output (your receiving) frequency.
- Press the MENU key to enter the menu.
- Enter [2][9] on the numeric keypad to get to frequency offset.
- Press MENU to select.
- Use the numerical keypad to enter the specified frequency offset. See the section called “29 OFFSET - Frequency shift amount" for details.
- Press MENU to confirm and save.
- Enter [2][8] on the numeric keypad to get to offset direction.
- Use the ▲/▼ keys to select + (positive) or - (negative) offset.
- Press MENU to confirm and save.
- Optional:
- Save to memory (see "Manual programming" for details).
- Set up CTCSS (see "CTCSS" for details).
- Press EXIT to exit the menu. If everything went well, you should be able to make a test call through the repeater.
NOTE: If you're experiencing problems making a connection to the repeater, check your settings and/or go through the procedure again. Certain Amateur Radio repeaters (especially in Europe) use a 1750Hz tone burst to open up the repeater. If you're unable to make a connection, contact the person in charge of the radio system or your local amateur radio club. If you want to listen to the repeater's input frequency instead, press the * key momentarily, and you'll reverse your transmit and receive frequencies. This is indicated in the LCD on the radio with an R in the top row, next to the + and - for the offset direction.
3.3.5 VOX (Voice Activated Transmit)

Image: VOX Function, allowing hands-free communication, ideal for activities like climbing.
This function allows hands-free conversations: just speak in the direction of the microphone, and communication will be automatically activated. In standby mode, press MENU + 7. The screen will display "VOX". Press MENU to enter the function. Press the ▲/▼ keys to turn off the VOX function or to select the VOX level (1-10), then press MENU to confirm. To return to standby mode, press EXIT.
NOTE: Level 1 is the least sensitive, while level 9 is the most sensitive. When the radio is in Scan or FM Radio mode, VOX is not enabled.
3.3.6 Dual Watch
The ability to monitor two channels at once can be valuable. This radio features Dual Watch functionality (single receiver) with the ability to lock the transmit frequency to one of the two channels it monitors.
Enabling or Disabling Dual Watch Mode
- Press the MENU key to enter the menu.
- Enter 7 on the numeric keypad to get to Dual Watch.
- Press MENU to select.
- Use the UP and DOWN keys to enable or disable.
- Press the MENU key to confirm.
- Press the EXIT key to exit the menu.
3.3.7 Stopwatch Timer

Image: Stopwatch function on the Baofeng UV-G30 PRO, suitable for outdoor sports.
In standby mode, press MENU + 44. The screen displays "STOP WATCH". Press MENU to enter the function. Press the ▲/▼ keys to enable (ON) the function, then press MENU to confirm. To return to standby mode, press EXIT.
Using the Stopwatch Timer:
When this function is ON, press MENU to start counting; press MENU again to re-start counting. To exit the function, stop the counting first, and then press the EXIT key.
3.3.8 DTMF (Dual-Tone Multi-Frequency)
DTMF is an in-band signaling method using dual sinusoidal signals. In two-way radio systems, DTMF is commonly used for automation systems and remote control, such as activating amateur radio repeaters.
DTMF Frequencies and Corresponding Codes
| 1209Hz | 1336Hz | 1477Hz | 1633Hz | |
|---|---|---|---|---|
| 697Hz | 1 | 2 | 3 | A |
| 770Hz | 4 | 5 | 6 | B |
| 852Hz | 7 | 8 | 9 | C |
| 941Hz | * | 0 | # | D |
The radio has a full implementation of DTMF, including the A, B, C, and D codes. The numerical keys, as well as the *, 0, and # keys, correspond to the matching DTMF codes. To send DTMF codes, press the key(s) corresponding to the message you want to send while holding down the PTT key. If the keypad lock is enabled, you can still send DTMF tones.
3.3.9 Customization
The radio allows you to define visual and audible features such as Display Illumination Time, MR/Channel Mode Display Format, Power On Message, Power On password, Keypad Beep, Roger Beep, Voice Prompt, etc., to suit your usage habits.
- 3.3.9.1 Display Backlight (ABR) - MENU 7: In standby mode, press MENU + 7. The screen displays "ABR". Press MENU to enter. Use ▲/▼ to select always on/delay time (ON/5sec/10sec/15sec/20sec), then press MENU to confirm. Press EXIT to return to standby.
- 3.3.9.2 Beep PROMPT (BEEP) - MENU 8: If enabled, a beep tone sounds every time a key is pressed. In standby mode, press MENU + 8. The screen displays "BEEP PROMPT". Press MENU to enter. Use ▲/▼ to turn ON/OFF the beep function. Press MENU to confirm and exit.
- 3.3.9.3 Voice Function (VOICE) - MENU 17: In standby mode, press MENU + 17. The screen displays "VOICE". Press MENU to enter. Use ▲/▼ to select OFF/ON. Confirm with MENU. Press EXIT to return to standby.
- 3.3.9.4 Language of the MENU (LANGUAGE) - MENU 18: This section shows the language of the MENU (English). In standby mode, press MENU + 18. The display shows "LANGUAGE".
- 3.3.9.5 Working Mode (MDF-A) - MENU 24: The radio has four working modes: Frequency mode (FREQ), Channel mode (CH), Channel name (NAME). To shift modes, in standby, press MENU + 24; select the desired working mode with ▲/▼ keys.
- 3.3.9.6 Roger Beep, End Transmission Tone (ROGER) - MENU 36: Roger Beep can be enabled/disabled (OFF/ON). In standby mode, press MENU + 36. The screen displays "ROGER". Press MENU to enter. Use ▲/▼ to select OFF/ON. Confirm with MENU. Press EXIT to return to standby.
- 3.3.9.7 Power On Message (POWER ON MSG) - MENU 40: Customize the welcome message. Options: VOLTAGE, MESSAGE, LOGO, MODEL NAME. In standby, press MENU + 40. The screen displays "POWER ON MSG". Press MENU to enter. Use ▲/▼ to select option and confirm with MENU. Press EXIT to return to standby.
- 3.3.9.8 Power On Password (Power On Password) - MENU 43: Request a password when the radio is turned on. In standby, press MENU + 43. The screen displays "POWER ON PWD". Press MENU to enter. Use ▲/▼ to enable/disable (ON/OFF) the password and confirm with MENU. Press EXIT to return to standby.
3.3.10 Reset - MENU 42
This transceiver has two Reset modes: VFO and ALL.
- Reset VFO: All settings except channels will return to default.
- Reset ALL: All settings will return to default.
Reset VFO
In standby mode, press MENU + 42. The screen displays "RESET". Press MENU to enter. Use ▲/▼ to select VFO, then press MENU to confirm. The display shows "Sure to reset?". Press MENU again to confirm. The transceiver will turn off and reboot.
Reset ALL
In standby mode, press MENU + 42. The screen displays "RESET". Press MENU to enter. Use ▲/▼ to select ALL, then press MENU to confirm. The display shows "Sure to reset?". Press MENU again to confirm. The transceiver will turn off and reboot.
4. Maintenance
4.1 Battery Maintenance Instructions
To help your battery work normally or prolong its life, observe the following instructions:
- Accumulated dust on the charging connector may affect normal charging. Use a clean and dry cloth to wipe it regularly.
- It is recommended to charge the battery under 5°C-40°C. Violation of this limit may cause battery life reduction or even battery leakage.
- To charge a battery attached to the product, turn it off to ensure a full charge.
- Do not remove the battery or unplug the power cord during charging to ensure a smooth charging process.
- Do not dispose of the battery in fire.
- Do not expose the battery to direct sunlight for a long time, nor place it close to other heating sources.
- Do not squeeze and penetrate the battery, nor remove its housing.
4.2 General Maintenance
Your Two-Way Radio is an electronic product of exact design and should be treated with care. The suggestions below will help you fulfill any warranty obligations and enjoy this product for many years.
- Do not attempt to open the radio for any reason! The radio's precision mechanics and electronics require experience and specialized equipment. The radio should under no circumstances be realigned as it has already been calibrated for maximum performance. Unauthorized opening of the transceiver will void the warranty.
- Do not store the radio under direct sunlight or in hot areas. High temperatures can shorten the life of electronic devices and warp or melt certain plastics.
- Do not store the radio in dusty and dirty areas.
- Keep the radio dry. Rainwater or dampness will corrode electronic circuits.
- If the radio diffuses a peculiar smell or smoke, immediately shut off its power and remove the charger or battery.
- Do not transmit without an antenna.
5. Troubleshooting Guide
| Phenomena | Analysis | Solution |
|---|---|---|
| Cannot turn on the radio. | The battery may be installed improperly. | Remove and reattach the battery. |
| The battery power may run out. | Recharge or replace the battery. | |
| The battery may suffer from poor contact caused by dirty or damaged battery contacts. | Clean the battery contacts or replace the battery. | |
| During receiving, the voice is weak or intermittent. | The battery voltage may be low. | Recharge or replace the battery. |
| The volume level may be low. | Increase the volume. | |
| Cannot communicate with other group members. | The antenna may be loose or improperly installed. | Turn off the radio, and then remove and reattach the antenna. |
| The speaker may be blocked. | Clean the surface of the speaker. | |
| You hear unknown voices or noise. | The frequency or signaling type may be inconsistent with that of other members. | Verify that your TX/RX frequency and signaling type are correct. |
| You may be too far away from other members. | Move towards other members. | |
| You may be interrupted by radios using the same frequency. | Change the frequency, or adjust the squelch level. | |
| Unable to hear anyone because of too much noise and hiss. | The radio in analog mode may be set with no signaling. | Request your dealer to set signaling for the current channel to avoid interference. |
| You may be too far away from other members. | Move towards other members. | |
| You may be in an unfavorable position (e.g., communication blocked by high buildings or underground area). | Move to an open and flat area, restart the radio, and try again. | |
| The radio keeps transmitting. | It may be the result of external disturbance (such as electromagnetic interference). | Stay away from equipment that may cause interference. |
| VOX may be turned on or the headset is not installed in place. | Turn off the VOX function. Check that the headphones are in place. |
NOTE: If the above solutions cannot fix your problems, or you have other queries, please contact your dealer for more technical support.
6. Technical Specifications
General
| Frequency Range | 136-174MHz (TX&RX), 220-260MHz (TX&RX), 400-520 MHz (TX&RX), FM65-108MHz (RX) |
| Power | 5W/2W |
| Channel Spacing | 25.0KHz (Wide)/12.5KHz (Narrow) |
| Memory Channel | 999 Groups |
| Operation Voltage | DC 7.4 V ±10% |
| Transmission Current | ≤1800mA |
| Receive Sensitivity | 0.25μV (12dB SINAD) |
| Rated Audio Power Output | 1W @16 ohms |
| Receive Current | ≤380mA |
| Connection for Accessories | 2 pin Kenwood jack |
| Antenna Impedance | 50 Ohm |
NOTE: All specifications may be modified without prior notice or liability.
7. User Tips
- For optimal battery life, ensure the radio is turned off during charging and remove it from the charger within 6 hours of full charge.
- When using the frequency copy function, ensure the source radio is transmitting clearly for accurate copying.
- Utilize the VOX function for hands-free operation during activities where pressing the PTT button is inconvenient.
- Regularly check the NOAA weather channels for local weather updates, especially when outdoors.
- If experiencing communication issues, first check battery charge, antenna connection, and ensure consistent frequency/signaling types with other users.
8. Warranty and Support
The Company endeavors to achieve the accuracy and completeness of this manual, but no warranty of accuracy or reliability is given. All specifications and designs are subject to change without notice due to continuous technological development. Unauthorized opening of the transceiver will void the warranty.
For technical support or any queries not covered in this manual, please contact your dealer or the manufacturer's customer service.
A PDF version of this user manual is available for download here.