BAOFENG BF-E88

Contents

Baofeng BF-E88 Walkie Talkie User Manual

Model: BF-E88 (E88/E88 PRO Series)

Introduction

Thank you for choosing the BAOFENG BF-E88 (E88/E88 PRO) FM two-way radio transceiver. This device is suitable for use in the 446 private mobile radio service (PMR446). It comes pre-programmed with 16 PMR446 frequencies, a maximum transmission power of 500 mW, and a bandwidth of 12.5 kHz. The BF-E88 features a fixed antenna and does not require registration or fees for use within the PMR446 band, though restrictions may apply in some non-EU countries.

Combining the latest radio communication technology with a sturdy mechanical frame, the BF-E88 is an ideal and effective solution for professionals needing to stay in touch with their team (e.g., construction sites, buildings, hotels) or for leisure users wanting to connect with friends and family.

Key Features:

  • 16 PMR446 Channels
  • UHF 400-470MHz Frequency Range
  • 155 Sub-Codes (50 CTCSS / 105 DCS codes)
  • Hands-Free Operation (VOX)
  • LED Flashlight
  • Emergency Alert Function
  • Battery Level Meter & Low Battery Audible Alert
  • Battery/Power Saver
  • Time-out Timer (TOT)
  • 2-pin Kenwood headset jack
  • 1500mAh Li-ion rechargeable battery pack
Baofeng BF-E88 Walkie Talkie with feature icons
Overview of Baofeng BF-E88 features including VOX, Power Saving, LED Light, Clear Sound, Alarm Function, and Encryption.

Safety Information

ATTENTION!

Before using this product, carefully read the RF Energy Exposure and Product Safety Guide that accompanies the radio. This guide contains essential instructions for safe usage, RF energy awareness, and control to ensure compliance with applicable standards and regulations.

  • Charger Warning: Using a different battery charger other than the one specified can cause damage to your device or may even cause explosions and personal injuries.
  • Do Not Open: Do not attempt to open the unit. Non-expert handling may damage the unit and/or void the warranty.
  • Power Supply: When using a regulated power supply, ensure the power voltage is 5V to avoid damage.
  • Temperature: High temperatures can shorten the life of electronic devices and warp or melt plastics. Avoid storing the radio in dusty or dirty areas.
  • Moisture: Keep the radio dry. Rainwater or dampness can corrode electronic circuits.
  • Unusual Odors/Smoke: If the radio emits a peculiar smell or smoke, immediately shut off its power and remove the charger or battery.
  • Antenna: Do not transmit without an antenna attached.

Package Contents

The standard package includes the following items:

  • 2 x BF-E88 Transceiver
  • 2 x 1500mAh Li-ion Battery Pack
  • 2 x Antenna
  • 2 x Belt Clip
  • 2 x Desktop Charger
  • 2 x Lanyard
  • 2 x User Manual
  • 1 x Box
Diagram of standard package contents for Baofeng BF-E88
Standard package contents for the BF-E88 walkie talkie.

Product Overview: Controls and Parts

Diagram of Baofeng BF-E88 walkie talkie controls and parts
Labeled diagram of the BF-E88 walkie talkie showing its main components.
  1. Antenna
  2. Flashlight
  3. Volume Knob with Power Switch
  4. LED Indicator: RED - Transmit (TX); GREEN - Receive (RX)
  5. PTT button (Push-To-Talk)
  6. LAMP button (LED Flashlight On/Off)
  7. SCAN button (Activate/Deactivate Scanning)
  8. Emergency button (Turn emergency alerts on/off)
  9. Speaker and Built-in microphone
  10. '+' button: Short press for channel selection. Long press to initiate a ringtone.
  11. 'MENU' button: Short press for menu functions and settings. Long press to lock/unlock function keys.
  12. Headset jack (Headset not included)
  13. LCD Display
  14. 'MON' button: Short press for channel selection. Long press for monitoring (weak signal monitoring).
  15. Li-ion Battery pack
Dimensions of Baofeng BF-E88 walkie talkie
Dimensions of the BF-E88: Total height 21cm (8.27in), Body height 11.5cm (4.53in), Width 5cm (1.97in), Depth 3cm (1.18in).

Setup

Battery Installation

Align the battery pack with the back of the radio and slide it into place until it clicks securely. Ensure the battery is fully seated.

Charging the Battery

The BF-E88 uses a 3.7V Li-ion rechargeable battery pack. To charge:

  1. Connect the AC/DC wall adapter to a mains power socket.
  2. Insert the jack of the wall adapter into the desktop charger plug.
  3. Place the BF-E88 transceiver into the desktop charger cradle.

A full charge typically takes 4-5 hours. For maximum battery life, it is recommended to charge the battery pack when the radio is off and the battery is fully discharged.

Baofeng BF-E88 in charging cradle with LED indicators
The smart LED indicator lights show charging status: Red for Charging, Green for Charging Complete.

Antenna Attachment

Screw the antenna clockwise onto the connector on the top of the radio until it is finger-tight. Do not overtighten.

Belt Clip Attachment

Attach the belt clip to the designated slot on the back of the radio using the provided screws.

Operating Instructions

Power On/Off and Volume Adjustment

  • To Turn On: Rotate the Power/Volume knob clockwise until you hear a mechanical "click". The LCD display will light up, and you will hear two different tone beeps.
  • To Adjust Volume: Continue rotating the Power/Volume knob clockwise to increase volume, or counter-clockwise to decrease it.
  • To Turn Off: Rotate the Power/Volume knob counter-clockwise until you hear a mechanical "click".

Choosing a Channel

Your radio has 16 channels. To communicate, both radios must be set to the same channel and privacy code (CTCSS/DCS).

  • Use the '+' or 'MON' buttons to select one of the 16 PMR channels.
  • If the keypad is locked, press and hold the 'MENU' button for 2 seconds to unlock it.

Talking on Your Radio (PTT)

  1. Press and hold the [PTT] button.
  2. Speak clearly and normally, holding the microphone 2-3 inches away from your mouth. The TX icon will appear on the display.
  3. To avoid cutting off the beginning of your transmission, pause briefly after pressing the [PTT] button before speaking.
  4. When finished speaking, release the [PTT] button. The RX icon will display, indicating you can receive incoming calls.

Monitor Mode Feature

This feature allows you to listen for weak signals on the current channel.

  • To Turn On: Press and hold the 'MON' button for 2 seconds until two beeps sound. The receiver circuit will open, allowing you to hear noise and weak signals. The RX icon will blink.
  • To Turn Off: Press and hold the 'MON' button for 2 seconds again. Two beeps will sound, and the RX icon will stop blinking.

Channel Scanning

Your radio can scan all 16 channels for activity.

  • To Start/Stop: Quickly press the 'SCAN' button.
  • The radio will scan channels and stop on any active channel. It will resume scanning after 5 seconds if the channel becomes inactive.
  • If you press the [PTT] button during a scan, the scanning function will stop on the active channel for 10 seconds before resuming.
  • To manually resume scanning, quickly press the '+' or 'MON' button.

Scanning Sub-Codes

To scan for CTCSS/DCS sub-codes:

  • Press and hold the 'SCAN' button to enter Sub-Codes scanning.
  • A flashing "CTC/DCS" will appear on the display. The radio will cycle through sub-codes.
  • Once a privacy code is determined, the "CTC/DCS" indicator will stop flashing.
  • Press the [PTT] button to save the scanned tone to memory.

Using the Flashlight

The BF-E88 includes a high-intensity LED flashlight.

  • Press the 'LAMP' button once to turn the flashlight on continuously (Always On mode).
  • Press the 'LAMP' button a second time to activate the Strobe Light (Strobe emergency mode).
  • Press the 'LAMP' button a third time to turn the flashlight off.
Baofeng BF-E88 with LED flashlight on
The integrated LED flashlight is useful in dark environments.

Emergency Alert Function

This feature signals other group members that you need help.

  • To Activate: Press and hold the [Emergency] button on the top of the radio for 3 seconds. The radio will emit a loud siren sound, and the flashlight will flash.
  • To Exit: Press the [Emergency] button again.

WARNING: The Emergency Alert feature should only be used in a genuine emergency.

Baofeng BF-E88 with emergency alert activated
The walkie talkie makes a loud siren and flashes red light when the emergency alert is activated.

CTCSS/DCS Tones Selection

The BF-E88 can receive in two modes: Open Traffic (hear all communications) or Group Mode (hear only messages with matching CTCSS/DCS tones).

To activate a CTCSS/DCS tone for RX and TX:

  1. Turn on the radio and select the desired channel.
  2. Press the 'MENU' button once until "oF" (blinking) appears on the right side of the display.
  3. Use the '+' or 'MON' buttons to display "CTCSS" (ct blinking) or "DCS" (dc blinking).
  4. Press 'MENU' to enter the CTCSS or DCS tones selection.
  5. Use the '+' or 'MON' buttons to select the desired tone.
  6. Press the [PTT] button or 'MENU' button to exit and save.

VOX Function (Hands-Free Operation)

The VOX function allows for hands-free conversations.

  1. Press the 'MENU' button 3 times until "VOX" appears on the display.
  2. Use the '+' or 'MON' buttons to select the desired sensitivity level (1=high, 2=medium, 3=low).
  3. Press the [PTT] button or 'MENU' button to exit and save.
  4. To disable VOX, select "oF" (OFF) in the VOX settings.

Setting and Transmitting Call Tones

The BF-E88 can transmit 10 different call tones to alert other radios in your group.

  1. Press the 'MENU' button 4 times until "CA" appears on the display.
  2. Use the '+' or 'MON' buttons to preview the 10 pre-programmed melodies.
  3. Press the [PTT] button or 'MENU' button to exit and save.
  4. To disable call tones, select "oF" (OFF) in the call tone settings.

To transmit your selected call tone, ensure both radios are on the same channel and sub-code, then press and hold the '+' button.

Keypad Lock

To prevent accidental changes to radio settings:

  • To Lock/Unlock: Press and hold the 'MENU' button for 2 seconds. A lock icon will appear/disappear on the display. The PTT, '+' and 'MON' keys remain active even when locked.

Keypad Beep

To deactivate the keypad beep:

  1. Press the 'MENU' button 6 times until "bP on" is displayed.
  2. Use the '+' or 'MON' buttons until the display shows "bP oF".
  3. Press the [PTT] button or 'MENU' button to exit and save.

Roger Beep (End Transmission Tone)

This function emits a tone when you release the PTT button, signaling to the other party that they can begin speaking. It is enabled by default.

To deactivate it:

  1. Press the 'MENU' button 7 times until "rb on" is displayed.
  2. Use the '+' or 'MON' buttons to select "rb oF".
  3. Press the [PTT] button or 'MENU' button to exit and save.

Dual Watch Mode

This function allows the radio to scan two channels for activity: the current channel and a selected second channel.

To set up Dual Watch:

  1. Press the 'MENU' button 8 times until "oF du" appears on the display.
  2. Use the '+' or 'MON' buttons to select the second channel, then press 'MENU'.
  3. Use the '+' or 'MON' buttons to select the CTCSS/DCS for the second channel, then press 'MENU'.
  4. The radio will begin Dual Watch, alternating between the home channel and the selected channel.
  5. To exit Dual Watch mode, press the 'SCAN' button.

Note: Dual Watch will not function if you set the same channel and sub-code as the current channel.

Maintenance

Your BF-E88 PRO is designed for long-lasting performance. Follow these suggestions to ensure its longevity:

  • Do not attempt to open the unit. Unauthorized modifications will void the warranty.
  • Ensure power supply voltage is 5V to prevent damage.
  • Avoid high temperatures, which can shorten the life of electronic components and deform plastics.
  • Do not store the radio in dusty or dirty environments.
  • Keep the radio dry. Moisture can corrode electronic circuits.
  • If you detect unusual smells or smoke, immediately power off the radio and remove the battery/charger.
  • Never transmit without the antenna attached.

Troubleshooting

Problem Possible Cause Solution
No power Battery discharged or not properly installed. Charge battery fully. Ensure battery is correctly installed.
Cannot transmit or receive Incorrect channel/sub-code, out of range, antenna not attached. Verify both radios are on the same channel and sub-code. Check antenna connection. Move closer to other radio.
Weak or noisy reception Out of range, obstructions, low battery. Move to an open area. Use Monitor mode to listen for weak signals. Charge battery.
Accidental setting changes Keypad not locked. Activate Keypad Lock by pressing and holding the 'MENU' button for 2 seconds.

Specifications

General
Frequency Range UHF 400-470MHz (PMR446)
Channels 16 PMR446
Working Temperature -10°C to +50°C
Operation Voltage DC 3.7V ±10%
Operation Mode Simplex
Dimensions (without Antenna) 115mm x 60mm x 33mm (4.53in x 2.36in x 1.30in)
Weight (Battery pack included) 150g
Antenna Impedance 50Ω
Battery Capacity 1500mAh
Transmitter
Frequency Stability ±2.5ppm
RF Output Power ≤500mW ERP (for PMR446)
Max Frequency Deviation ≤2.5KHz
Audio Distortion ≤3%
Adjacent Channel Power < 60dB
Receiver
Receive Sensitivity < 0.2µV @20dB SINAD
Audio Distortion ≤3%
Audio Response 300Hz ~ 3KHz

User Tips

  • Optimal Range: The maximum range is achieved in open spaces with clear line of sight, such as mountains (up to 10 km). Obstructions like buildings, trees, or metallic structures can significantly reduce range (1-2 km in urban areas, 4-6 km in open areas with some obstructions).
  • Clear Communication: When transmitting, hold the radio 2-3 inches from your mouth and speak clearly.
  • Battery Life: To maximize battery life, ensure the battery is fully charged before use and recharge it when the radio is off and fully discharged.
  • Channel Privacy: Utilize CTCSS/DCS sub-codes to minimize interference and ensure more private conversations within your group.

Warranty and Support

The BF-E88 PRO is designed to meet all warranty obligations and provide years of enjoyment. As with all electronic devices, please follow the maintenance guidelines to avoid voiding your warranty.

EU Declaration of Conformity

Baofeng and Pofung declare that the radio equipment type listed in the Technical Specifications complies with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following link: View User Manual (PDF).

For local support, please contact your Baofeng dealer or send an email to wangjianhui@baofengradio.com.

Disclaimer

While every effort has been made to ensure the accuracy and completeness of this manual, we do not bear responsibility for possible errors or omissions. Due to continuous technological development, we reserve the right to change the design and specifications of the product without prior notice. No part of this handbook may be copied, modified, translated, or disseminated without prior written authorization.

EU Contact: APEX CE SPECIALISTS LIMITED, Unit 3D North Point House, North Point Business Park, New Mallow Road, Cork, T23 AT2P, Ireland

Manufacturer: PO FUNG ELECTRONIC (HK) INTERNATIONAL GROUP COMPANY LIMITED, Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.