1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your JUMUNION Car Parktronic LED Parking Sensor System. Please read this manual thoroughly before installation and use to ensure proper function and safety.
1.1. Safety Warnings
- Keep out of reach of children.
- In case of ingestion, seek medical attention immediately.
1.2. General Precautions
- Keep away from ignition sources.
- Ensure adequate ventilation during installation and operation.
2. Product Overview
The Car Parktronic LED Parking Sensor System is designed to assist drivers in parking by detecting obstacles and providing visual and audible alerts. The system is available in 4-sensor and 8-sensor configurations.
2.1. Components
- Main Control Box: Central unit for processing sensor data.
- LED Display Indicator: Provides visual distance feedback and audible alerts.
- Parking Sensors: Ultrasonic sensors for obstacle detection (4 or 8 depending on model). Each sensor has a 2.5-meter cable.
- Power Cable: For connecting the control box to the vehicle's power supply.
- Hole Saw: Tool for drilling sensor mounting holes in the bumper.
- Double Side Sticker: For mounting the LED display.
2.2. Key Features
- Automatic activation of rear radar when reversing.
- Automatic activation of front radar after reversing for approximately 10 seconds to prevent scratching, especially in the right front corner.
- Front radar activation when the brake pedal is pressed, stopping after approximately 10 seconds.
- Visible LED display with backlight for clear distance indication.
- Audible 'Bi Bi Bi' alerts for proximity warnings.
- Detection range: 0.2 to 2.6 meters.
3. Installation Guide
Proper installation is crucial for the optimal performance of the parking sensor system. It is recommended to have this system installed by a qualified professional.
3.1. Sensor Placement
The sensors should be installed on the vehicle's bumper. Ensure no other parts of the vehicle fall into the detecting range of the sensors to avoid false detection.
- For 2 sensors: Best position is 0.6-0.8 meters from the center.
- For 4 sensors: Best position is 0.3-0.4 meters from the center.
- Use the provided hole saw to drill holes in the bumper for insert-in sensors.
- Ensure sensors are facing outwards and not obstructed.
3.2. Wiring Connection
Connect the sensors, LED display, and power to the main control box as per the diagram below.
- Yellow Wire: Connect to Car Reversing Light "+"
- White Wire: Connect to Car Brake Light "+"
- Black Wire: Connect to GND (0V)
- Red Wire: Connect to ACC power "+"
4. Operating Instructions
The system operates automatically based on vehicle actions.
4.1. Basic Operation
- When the vehicle is reversing, the rear radar automatically starts to work, detecting obstacles behind the vehicle.
- Upon completion of reversing, the radar in front of the car automatically activates to detect obstacles, helping to prevent scratching, especially in the right front corner of the vehicle. This front radar typically operates for about 10 seconds after reversing.
- When the vehicle is not reversing, if the brake pedal is pressed, the front radar is temporarily turned on. It will stop working after approximately 10 seconds if no further braking or reversing action is detected.
4.2. Display and Audio Feedback
The LED display shows the distance to obstacles, and an audible 'Bi Bi Bi' sound indicates proximity. The frequency of the beeps increases as the vehicle gets closer to an obstacle.
4.3. Verification
After installation and initial setup, drive for a few minutes to confirm that the warning light is off when no obstacles are present and that the system responds correctly to obstacles.
5. Maintenance
To ensure the longevity and accuracy of your parking sensor system, follow these simple maintenance guidelines:
- Sensor Cleaning: Regularly clean the sensors to remove dirt, mud, snow, or ice, which can interfere with their detection capabilities. Use a soft cloth and mild cleaning solution.
- Cable Inspection: Periodically check all wiring connections for any signs of wear, damage, or loose connections.
- Display Cleaning: Keep the LED display clean and free from dust for optimal visibility.
6. Troubleshooting
If you encounter issues with your parking sensor system, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| System not activating or no display. | Loose power connection, faulty control box, incorrect wiring. | Check all power and signal connections. Ensure correct wiring to ACC, brake, and reverse lights. Verify power supply. |
| Sensors not detecting obstacles or false alarms. | Dirty/obstructed sensors, incorrect sensor angle, faulty sensor. | Clean sensors thoroughly. Ensure sensors are installed at the correct angle and not obstructed by vehicle parts. Test individual sensors if possible. |
| Inconsistent distance readings. | Environmental factors (heavy rain, snow), sensor interference, loose sensor connection. | Ensure sensors are clean. Check sensor connections to the control box. Avoid using the system in extreme weather conditions if performance is affected. |
| Audible alarm not working. | Faulty speaker in display, loose connection to display. | Check the connection between the display and the control box. Ensure the display unit is functioning correctly. |
7. Specifications
| Feature | Specification |
|---|---|
| Model Name | LD011 |
| OSD Language | English |
| Talk Range | 0.2 ~ 2.6 meters |
| Type | Visible |
| Sensor Diameter | 2.5 cm |
| Sensor Depth | 2.2 cm (1.8 cm mounting depth) |
| Sensor Cable Length | 2.5 meters |
| Display Dimensions (L x H) | 10 cm x 2 cm |
| Display Cable Length | 5 meters |
| Origin | Mainland China |
8. User Tips
Here are some tips to enhance your experience with the Car Parktronic system:
- Consider the color of your sensors: The system offers sensors in various colors (black, blue, silver, gray, white, red) to match your vehicle's bumper for a seamless look.
- Regularly check sensor alignment: Ensure sensors remain flush with the bumper and are not pushed inward or outward, which could affect accuracy.
- Test in different environments: Familiarize yourself with how the system reacts in various conditions, such as in tight parking spaces, near low obstacles, or in adverse weather.
9. Warranty and Support
For detailed warranty information and customer support, please refer to the official user manual PDF or contact the seller directly. The user manual PDF can be accessed via the following link: User Manual (PDF).
If you experience any issues not covered in this manual or require further assistance, please reach out to JUMUNION customer service or your point of purchase.