1. Introduction
Thank you for choosing this Intelligent Car Information System. This product is designed to integrate CarPlay and Android Auto functionalities into your Volvo vehicle, allowing you to access music, navigation, and other smartphone features directly on your car's original screen. This seamless upgrade enhances connectivity without altering your vehicle's factory setup, transforming your existing infotainment system into a smart, intuitive hub.
The kit is compatible with various Volvo models from 2018-2025 that feature a 9-inch factory display. It preserves all original controls and safety features, ensuring a fully integrated experience.
2. Safety Precautions
- Installation should only be performed by qualified professionals to prevent damage to vehicle electrical systems.
- Always disconnect the car battery before installation to avoid short circuits.
- Ensure all connections are secure and properly insulated to prevent fire hazards.
- Do not obstruct airbags, driver visibility, or vehicle controls during installation.
- Avoid modifying essential vehicle safety systems or wiring.
- Operate connected devices only when the vehicle is parked to avoid driver distraction.
- Regularly check for loose connections or signs of overheating during use.
- Discontinue use immediately if unusual smells, sounds, or malfunctions occur.
- Ensure product usage complies with all local traffic laws and regulations.
- Keep the product away from water, extreme temperatures, and direct sunlight when not in use.
3. Product Features
- Apple CarPlay: Connect your iPhone to access navigation, music, calls, and messages via the car's screen or voice commands. Supports hands-free operation and enhances driving safety.
- Android Auto: Connect your Android phone to access essential apps safely. Prioritizes driving-focused features for navigation, music, calls, and messages via voice or touch.
- Full Screen Display: Converts half-screen CarPlay to full-screen mode, maximizing your Volvo’s high-resolution display.
- Wireless & Wired Connectivity: Supports both wireless and wired CarPlay & Android Auto via dual-band WiFi (2.4G/5.8G) and Bluetooth 5.0.
- Perfect OEM Integration: Retains factory display, steering wheel controls, and all original vehicle functions. Seamlessly switch between the factory system and CarPlay/Android Auto.
- Enhanced Audio Quality: Built-in Digital Signal Processor (DSP) with adjustable EQ delivers premium sound through your Volvo’s audio system.
- Camera System Ready: Two RCA inputs (PAL/NTSC) allow connection of front or rear cameras.
- Advanced Parking Assistance: Compatible with HD 360° panoramic systems with dynamic guidance lines.
- Voice Control: Activate Siri or Google Assistant through your steering wheel buttons.

Original Car Upgrade Smart Module for Volvo XC40/XC60/XC90/S60/S90/V90 2018-2025, highlighting Bluetooth, CarPlay, Android Auto, Factory Protocol, Lossless Installation, Voice Control, Live Map, Online Entertainment features.

Comparison of OEM Car System screen with Apple CarPlay and Android Auto interfaces on a Volvo display, illustrating the switch functionality.

Intelligent Voice Control feature, showing 'Hey Siri' and Google Assistant commands on the car screen.
4. Compatibility
This retrofit kit is compatible with the following Volvo models and years, specifically those equipped with a 9-inch factory display (often referred to as 'Tesla Screen').
| Car Model | Years | Screen Size |
|---|---|---|
| XC40 | 2018-2025 | 9" Tesla Screen |
| XC60 | 2018-2025 | |
| XC90 | 2018-2025 | |
| S60 | 2018-2025 | |
| S90 | 2018-2025 | |
| V90 | 2018-2025 |

Table listing supported Volvo models (XC40, XC60, XC90, S60, S90, V90) with years (2018-2025) and screen size (9" Tesla Screen).
5. Package Contents
The following items are included in your package:
- 1 x Volvo Decoder Unit
- 1 x Power Harness
- 1 x LVDS IN Cable
- 1 x LVDS OUT Cable
- 1 x USB Connection Cable

Package & Accessories diagram, showing the decoder unit dimensions (139mm x 92mm x 20mm) and included cables: Power cable, LVDS OUT, LVDS IN, RCA & USB cable.
6. Setup and Installation
This kit features a plug-and-play installation, requiring no coding or wire cutting. However, professional installation is highly recommended to ensure correct setup and avoid damage to your vehicle.
6.1 Wiring Diagram
The decoder connects at three main points: under the steering wheel, behind the driver’s instrument cluster, and to the central infotainment display unit. Refer to the detailed wiring diagram below for connections.

Detailed wiring diagram for Volvo vertical screen, showing connections for original car screen LVDS cable, original car instrument gateway line, original steering column gateway wiring, and radar decoding box.

Image showing the decoder unit installed under the dashboard, with wiring connections visible.

Close-up of a wiring connector during installation.
6.2 DIP Settings & Switch
Adjust the DIP switches according to your specific car model and screen size. After making changes, restart the decoder for the settings to take effect. Ensure the dial is set to "ON" for the selected options.
| Car Model | Year | Screen Size | DIP Setting |
|---|---|---|---|
| XC40/XC60/XC90/V90/S60/S90 | 2018-2021 | 9" Tesla Screen | 2 ON, 247 ON |
| XC40/XC90/V90/S60/S90 (Android system) | 2022-2025 | 9" Tesla Screen | 24 ON |
| XC60 (Android system) | 2022-2025 | 9" Tesla Screen | 24/48 ON |
7. Operating Instructions
7.1 Button Control
The system integrates with your original steering wheel buttons and touch screen for control.
| Button | Operation | Function |
|---|---|---|
| ▶▶| | Short press | Next song |
| |◀◀ | Short press | Previous song |
| + | Short press | Increase the volume |
| − | Short press | Decrease the volume |
| ▶▶| or |◀◀ (on steering wheel) | Long press | Switch between OEM screen and interface screen |
| Menu/Home button (on steering wheel) | Long press | Switch between OEM screen and interface screen |
| Touch screen | Touch | Control function |

Original Car Functions retained, showing steering wheel buttons for media control and touch screen operation for navigation.
7.2 Wireless Connection (CarPlay & Android Auto)
For wireless functionality, ensure your phone's Bluetooth and Wi-Fi are enabled. The system uses Bluetooth for initial pairing and Wi-Fi for data transmission.
7.2.1 Wireless CarPlay Connection Steps
- Turn on your iPhone's Bluetooth and Wi-Fi.
- On your iPhone, select the Bluetooth device named "CAR Audio_XXXX" (where XXXX is a specific identifier).
- A pairing request will pop up. Confirm the code displayed on both devices.
- After successful Bluetooth pairing, a Wi-Fi connection will be established to transmit data. The Bluetooth connection may then disconnect, which is normal.
- Ensure your vehicle's audio system is set to Bluetooth music mode for optimal audio performance.

Wireless CarPlay interface on a Volvo screen, showing music playback and navigation, with a phone displaying CarPlay.

Bluetooth Audio Output setup, showing steps to pair car Bluetooth, connect CarPlay, and select sound output (Volvo or Car BT).
7.2.2 Wireless Android Auto Connection Steps
- Turn on your Android phone's Bluetooth and Wi-Fi.
- On your Android phone, select the Bluetooth device named "CAR Audio_XXXX".
- After successful Bluetooth pairing, follow the on-screen prompts for Android Auto connection.
- Ensure your vehicle's audio system is set to Bluetooth music mode for optimal audio performance.

Wireless Android Auto interface on a Volvo screen, showing Spotify and Google Maps, with a phone displaying Android Auto.
7.3 External Settings (Rear View Camera & Radar)
The CarPlay interface supports external camera inputs and radar integration.
7.3.1 Rear View Camera Input
Connect your aftermarket rear view camera to the RCA inputs on the decoder unit. This allows for clear rearview imagery on your car's display.

Diagram illustrating Rear View Camera Input connections to the Upgrade Kit, showing USB, LVDS OUT, LVDS IN, and GND connections.
7.3.2 Radar and Trajectory Settings
If your aftermarket camera supports reversing trajectory lines, you can enable them through the system settings:
- Enter the system settings: Go to "Factory mode" > "Advanced mode".
- Enter the password "888888".
- Navigate to "MCU setup" and uncheck the "A1" option to display reversing trajectory lines.
- For aftermarket radar options, uncheck the "A2" box.
- Return to the previous level and click "Restart system" for changes to take effect.
- If connecting a front camera, select the "A3" option.

Screenshot of MCU Setup menu for radar and trajectory settings, showing options for A1 and A2 boxes.
8. Maintenance
To ensure the longevity and optimal performance of your CarPlay & Android Auto Decoder Retrofit Kit, consider the following maintenance tips:
- Keep the decoder unit free from dust and moisture.
- Periodically check all cable connections to ensure they remain secure.
- Avoid exposing the unit to extreme temperatures or direct sunlight for prolonged periods.
- If cleaning is necessary, use a soft, dry cloth. Do not use liquid cleaners or solvents.
9. Troubleshooting
9.1 Why does the Box's Bluetooth disconnect?
The wireless CarPlay/Android Auto system uses Bluetooth for initial pairing and then switches to Wi-Fi for data transmission. To avoid interference, the Bluetooth connection will often disconnect once the Wi-Fi connection is established. This is a normal operating behavior.
9.2 Cannot connect CarPlay/Android Auto, but Bluetooth is paired.
If Bluetooth is paired but CarPlay/Android Auto fails to connect, try the following:
- On your iPhone: Go to Settings > General > Transfer or Reset [Device] > Reset > Reset Network Settings.
- On your Android phone: Forget the device's Bluetooth connection and re-attempt pairing.
9.3 Why is the wireless CarPlay/Android Auto connection unstable?
An unstable wireless connection can be caused by several factors:
- Physical Obstruction: Ensure that the mounted position of the CarPlay box is not blocked by metal components, as this can impair Wi-Fi signal transmission.
- Wi-Fi Channel Interference: Switch the Wi-Fi channel within the CarPlay box settings. Go to Factory Mode > Connectivity Settings > Hotspot Band and select channel 1, 6, or 11, depending on the optimal channel for your region.
10. Specifications
| Parameter | Value |
|---|---|
| Operating Voltage | 9-16V (14.4V rated) |
| Operating Temperature | -30°C to +75°C |
| Storage Temperature | -30°C to +85°C |
| Ambient Humidity | <98% (at 45°C), 65±5% (rated) |
| Power Consumption Current | 1A (rated), 3A (Max) |
| Shutdown Current | 300mA (Clock is on) |
| Quiescent Current | Less than 3mA |
| Charging Current | ≤2A. If USB charging current >1A, the host machine activates circuit protection to control current within 15A to prevent product damage. |
| Dimensions (Decoder Unit) | 139mm x 92mm x 20mm |
11. User Tips
- Verify Compatibility: Always double-check your Volvo model and year against the compatibility list (e.g., 2018-2025 models with a 9-inch screen). If your car is a 2016 model, it might not be compatible, as indicated by some user inquiries.
- Professional Installation: While the kit is plug-and-play, professional installation is highly recommended to ensure all connections are correct and secure, preventing potential issues.
- Optimal Wi-Fi: If you experience unstable wireless CarPlay/Android Auto, try changing the Wi-Fi channel in the decoder's factory settings (Factory Mode > Connectivity Settings > Hotspot Band) to 1, 6, or 11 to reduce interference.
12. Warranty and Support
For any technical issues or support inquiries, please contact our technical support team.
Email: techsupport@anyfar.com
Please provide your product model (RM-VLV2510F) and a detailed description of the issue when contacting support.