FastDeng Only COB LED Strip Light

Contents

COB LED Strip Light User Manual

Model: Only COB LED Strip Light

Brand: FastDeng

Introduction

This manual provides essential information for the safe and effective use of your FastDeng COB LED Strip Light. This flexible LED strip is designed for various DIY decorative lighting applications, offering high brightness and easy installation. Please read this manual thoroughly before installation and operation.

Safety Precautions

Read carefully before installation and use:

  1. Do not expose the strip to water or damp environments; it is not waterproof (IP20 rated).
  2. When using with LED strips, select an appropriate power rating to avoid overloading.
  3. Keep away from children, pets, and flammable materials.
  4. Ensure adequate ventilation during use to prevent overheating.
  5. Disconnect power before installation, cleaning, or maintenance.

Product Specifications

Feature Specification
Name COB LED Strip Light
Voltage DC 12V / DC 24V
Plug Type Dupont Male
LED Strip Width 8mm
Waterproof Grade IP20 (Non-waterproof)
LEDs Quantity 320LEDs/m
Available Lengths 1m, 2m, 3m, 4m, 5m
Emitting Color Warm White (2800K-3000K) / Neutral White (4000K-5000K)
12V COB Cuttable Unit 25mm (2.5cm)
24V COB Cuttable Unit 50mm (5cm)
Luminous Flux 249-2000 lumens
Average Life 50,000 hours
Power Consumption 7.36W/m
Certification CE
Power Source DC
Recommended Occasion Living room

Package Contents

Your package should contain the following:

  • 1 x COB LED Strip Light (with Dupont Male Connector)

Note: Power supply is NOT included and must be purchased separately.

COB LED Strip Light with Dupont Male Connector
Image: COB LED Strip Light with Dupont Male Connector and power cable.
COB LED Strip Light with Dupont Connector
Image: A coiled COB LED strip light with a Dupont connector, indicating it's the strip only.

Setup and Installation

Important Notes Before Installation:

  • This product is only the COB light strip; a power supply is not included.
  • The connector is a Dupont Male type, not a standard DC female connector.
  • The COB strip light cannot be directly connected to AC 110V/220V. You MUST use a DC 12V or DC 24V transformer (power supply) appropriate for the strip's voltage.

1. Cutting the LED Strip (Optional)

The LED strip can be cut to your desired length at designated cutting points. Ensure you cut only along the marked lines to avoid damaging the circuit.

  • For DC 12V COB strips: Cuttable unit is 25mm (2.5cm).
  • For DC 24V COB strips: Cuttable unit is 50mm (5cm).
DC 12V COB LED Strip cutting points
Image: Diagram showing cuttable points for a DC 12V COB LED strip, marked every 2.5cm.
DC 24V COB LED Strip cutting points
Image: Diagram showing cuttable points for a DC 24V COB LED strip, marked every 5cm.

2. Mounting the LED Strip

The COB LED strip features an adhesive backing for easy mounting:

  1. Clean the surface where the strip will be installed, ensuring it is dry and free of dust or grease.
  2. Peel off the protective backing from the adhesive tape on the back of the LED strip.
  3. Carefully press the strip onto the desired surface, applying even pressure along its length to ensure good adhesion.
Adhesive tape sticker on LED strip
Image: Illustration of the adhesive tape on the back of the LED strip for mounting.

3. Connecting to Power

Connect the Dupont Male connector of the LED strip to a compatible 2-pin Dupont interface on your DC 12V or DC 24V LED transformer/power supply. Ensure the voltage of your power supply matches the voltage of your LED strip (12V or 24V).

Port Details for 2-pin Dupont interface
Image: Diagram showing a controller with multiple 2-pin Dupont interfaces suitable for connecting LED strip lights.
COB LED Strip with Dupont Male Connector
Image: Close-up of the Dupont Male Connector on the COB LED strip.
COB LED Strip Light only, no power supply
Image: The COB LED strip light as a standalone component, emphasizing the need for an external power supply.
Warm White and Neutral White COB LED strip comparison
Image: Comparison of Warm White and Neutral White COB LED strips, showing different color temperatures.

Operating Instructions

Once the LED strip is properly installed and connected to a compatible DC 12V or DC 24V power supply, simply turn on the power supply to illuminate the strip. If your power supply or controller has a switch, use it to control the light.

Care and Maintenance

  • Gently wipe the LED strip with a dry cloth or a slightly damp soft cloth to clean.
  • Do not use chemical cleaners, as they may damage the strip.
  • When not in use for extended periods, store the LED strip in a dry place.

Troubleshooting

  • Light not turning on:
    • Ensure the power supply is connected and switched on.
    • Verify that the power supply voltage matches the LED strip's voltage (DC 12V or DC 24V).
    • Check all connections, especially the Dupont connector, for secure contact.
    • Inspect the strip for any visible damage or incorrect cuts.
  • Uneven lighting or flickering:
    • Ensure the power supply is adequate for the length of the strip.
    • Check for loose connections.
    • Verify that the strip is not bent too sharply, which can damage internal circuits.

User Tips

  • For optimal brightness and consistent performance, ensure all connections are firm and the correct voltage power supply is used.
  • The easy-to-operate Dupont connector simplifies installation, making it convenient for DIY projects.
  • Consider the emitting color (Warm White or Neutral White) based on the ambiance you wish to create in your living space.

Warranty and Support

For after-sales service or any product-related inquiries, please contact our official customer service. Be prepared to provide proof of purchase for assistance.

A detailed user manual in PDF format is also available for download: User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.