Toviyon TPA Series

Contents

Tovoyon Adjustable DC Power Supply User Manual

Models: TPA305, TPA3010, TPA605, TPA1203

1. Introduction & Safety Summary

Welcome to your Tovoyon DC regulated power supply. This manual provides essential safety instructions for the operation, use, and storage of your TPA series power supply. Please read this manual thoroughly before operation to ensure your personal safety and prevent damage to the power supply or connected equipment.

Safety Symbols

The following safety symbols may appear in this manual or on the machine:

Warning Label symbol

Warning Label

High Volt Danger symbol

High Volt Danger

Grounding symbol

Grounding

CE Certification Mark symbol

CE Certification Mark

Do Not Litter symbol

Do Not Litter

Indoor Use symbol

Indoor Use

Note: The specific image URLs for safety symbols were not provided in ALLOWED_URLS, so placeholder images are used. Please refer to the physical product or original manual for exact symbols.

2. Product Overview

The TPA series is a digital display programmable switching DC regulated power supply that can simultaneously display voltage, current, and power. It is widely used in product aging, battery charging, R&D testing, schools, and production lines. Its output voltage and current are both adjustable via an encode knob, continuously adjustable between 0 and the nominal value.

The power supply has excellent stability and ripple coefficient, and features multiple protection circuits including short-circuit protection (OCP), overvoltage protection (OVP), overcurrent protection, and overtemperature protection. It boasts an attractive design, user-friendly operation, and the ability to work at full capacity for extended periods. It is equipped with a USB fast charging interface and offers optional PC software control functionality.

Key Features:

  • Adjustable DC power supply with multiple output modes: 30V 10A / 30V 5A / 60V 5A / 120V 3A
  • Precise voltage and current regulation for stable output
  • High-efficiency switching power supply design
  • Clear digital display and user-friendly control panel
  • Built-in Overcurrent Protection (OCP), Overvoltage Protection (OVP), and Short-Circuit Protection
  • Compact structure, low heat generation, long service life
  • Ideal for laboratory use, electronic repair, DIY projects, and industrial testing
  • USB-A and USB-C fast charging ports (18W USB-A, 18W USB-C, QC3.0)
  • 4 Groups Memory Storage Function for frequently used parameters
  • One-click output locking to prevent accidental operations
Tovoyon TPA series features overview
Figure 1: Tovoyon TPA Series Features Overview. Includes icons for OCP, OVP, Encoder Adjustment, Low Ripple Low Noise, 4 Sets Of Memory, Cooling Fan, Enhanced Durability, Short Circuit Alarm, Over-temp Protection, One-click Output Lock, C.C C.V, TIME, MA, OPP.

3. Specifications

Parameter TPA305 TPA3010 TPA605 TPA1203 TPA1602
Output Volt0-30V0-30V0-60V0-120V0-160V
Output Current0-5A0-10A0-5A0-3A0-2A
Output Power0-150W0-300W0-300W0-360W0-320W
Fuse3.15A5A5A5A5A
AccessibilityDual fast charging ports, short circuit protection, four storage groups, lock function, buzzer, one-button output.
Voltage Stability (C.V)≤0.5% + 3mV
Load Stability (C.V)≤0.5% + 3mV
Ripple (C.V)≤0.5% Vp-p
Current Stability (C.C)≤0.5% + 3mA
Load Stability (C.C)≤0.5% + 3mA
Ripple (C.C)≤0.5% Ap-p
Product DimensionsLength 214mm, Width 90mm, Height 156mm
Product WeightNet weight: 1.17 kg. Gross weight: 1.55 kg.
Operating Temp0°C ~ 40°C, Relative humidity: <80%RH
Storage Temp-10°C ~ 50°C. Relative humidity: <70%RH
Protection MethodOvervoltage Protection, Overcurrent Protection, Overtemperature Protection, Short Circuit Protection
Display Accuracy0.5% + 3 words
Maximum ResolutionVolt: 0.001V; Current: 0.001A

The above parameters were measured at an ambient temperature of 25±5°C, relative humidity <80%RH, and after preheating for 30 minutes. Actual parameters may vary slightly.

Tovoyon DC Power Supply dimensions
Figure 2: Product Dimensions.

4. Front Panel Introduction

Front Panel Diagram of Tovoyon DC Power Supply
Figure 3: Front Panel Layout.
No. Description No. Description
1Voltage Display12Short-Circuit/Overcurrent Protection Switch (OCP)
2Current Display13Over Voltage Protection Switch (OVP)
3Power Display14Buzzer Switch
4C.V (Constant Voltage Indicator Light)15Output Switch
5M1-M4 Storage Indicator Light16USB-A Fast Charging Port
6C.C (Constant Current Indicator Light)17USB-C Fast Charging Port
7OPN Indicator Light18Power Switch
8Current adjustment knob19Negative Output Port (Black)
9Voltage Adjustment Knob20Ground Terminal (Green)
10Button Lock Switch21Positive Output Port (Red)
11Storage Selection/storage Value Setting Switch22Not Used

5. Back Panel Description

Back Panel Diagram of Tovoyon DC Power Supply
Figure 4: Back Panel Layout. (Note: Specific image URL for back panel diagram was not provided in ALLOWED_URLS, so a placeholder is used. Please refer to the physical product or original manual for the exact diagram.)
No. Description
22Temp-Controlled Cooling Fan
23Power Outlet
24Fuse Box
25USB/RS-232/RS-485 Communication Port (Optional)

6. Setup

6.1 AC Input

Please verify the AC voltage input permitted for this machine. Refer to the label information located near the power outlet on the back of the machine.

  • 230V ± 10% 50Hz
  • 115V + 10% 60Hz

Warning:

Incorrect AC voltage input will cause serious damage to the machine. Please ensure that the machine requires the correct input voltage.

6.2 Connect the Ground Wire

When using this product, please ensure the power cord is properly grounded. If the power outlet does not have a ground wire, you can use a wire to connect the machine's grounding terminal to the earth. Proper grounding can effectively prevent machine leakage and reduce output ripple interference.

Important:

Proper grounding effectively prevents machine leakage and can also reduce output ripple interference.

6.3 Connect the Load Device

  1. Securely connect the output wires to the power supply terminals according to the positive (+) and negative (-) markings.
  2. Securely connect the other end of the output lead to the positive terminal of your load device.

Notice:

Incorrect connections may damage the power supply and the load connected to it. When connecting loads such as batteries, do not reverse the "+" and "-" terminals, as this may damage the power supply.

7. Operating Instructions

7.1 Constant Voltage Constant Current Mode

The power supply output modes are divided into two types: constant voltage output (C.V) and constant current output (C.C). The output mode is determined by the voltage and current values set by the user and the load connected to the power supply. The voltage or current value output by the power supply will not exceed the voltage and current values set by the user. In constant voltage mode, the output voltage is equal to the user-set voltage value. In constant current mode, the output current is equal to the user-set current value.

Important Note on CV/CC Transition:

During actual C.V operation, if the load resistance decreases and causes the output current to increase to the set current value, the power supply will automatically switch to C.C mode. When the load resistance continues to decrease, the current will remain at the set current value while the voltage proportionally decreases (I=V/R). At this point, increasing the load resistance or raising the current set value will restore the C.V output mode.

Video 1: Demonstration of voltage stability under full load, memory function, and output lock. Shows adjusting voltage to 30V, current to 10A, clicking output, setting load current to 10A, testing voltage, and observing stable 30V output. Also demonstrates memory recall and output lock functionality.

7.2 VOLTAGE Adjustment Knob

Used to adjust the voltage setting. Rotate clockwise to increase the value; rotate counterclockwise to decrease the value. Pressing the voltage knob will jump to the left, skipping a character position. After 3 seconds, the flashing will stop and the current setting value will be saved.

High-Precision Encoder Adjustment Knob for Voltage
Figure 5: High-Precision Encoder Adjustment Knob. Press the knob to switch each digit when it flashes; turn the knob to customize each digit in the range of 0-9.

7.3 CURRENT Adjustment Knob

Used to adjust the current setting. Rotate clockwise to increase the value; rotate counterclockwise to decrease the value. Pressing the current knob will jump to the left, skipping a character position. The flashing will stop 3 seconds after the current setting is complete, and the current setting will be saved.

7.4 Button Lock Switch (LOCK)

Used to lock the state of the push-button switches (excluding the power switch and LOCK button lock switch) and adjustment knobs on the front panel to prevent accidental operation.

One-click output locking feature
Figure 6: One-click output locking. Press the LOCK button to disable all operations, preventing accidental changes during work. Press LOCK again to resume operations.

7.5 Memory Storage Group Selection/Storage Value Setting

This machine has four sets of memory functions (M1-M4), which makes it easy to store and recall frequently used parameters.

  • Storage Group Selection: Press the MEMORY button to select any one of the four preset voltage/current storage values. The selection result can be confirmed through the display screen and the M1~M4 storage indicator lights.
  • Stored Value Settings: To change a value stored in M2, for example: press the MEMORY button to select M2 for storage, then press and hold the MEMORY button for 3 seconds to enter the parameter setting interface (you will hear two "beep" sounds). Use the VOLTAGE/CURRENT knob to adjust to the desired voltage/current value. After modification, press and hold the MEMORY button for 3 seconds within 8 seconds to save, and the setting will be completed (you will hear two "beep" sounds). If you do not save within 8 seconds, the parameter setting interface will be automatically exited without saving.
4 Groups Memory Storage Function
Figure 7: 4 Groups Memory Storage Function. Numerical Storage: press the MEMORY button to select M1, M2, M3 and M4 in sequence.

7.6 OCP Short-Circuit Protection/Overcurrent Protection Switch

Press the OCP button to enable/disable the OCP short-circuit protection/overcurrent protection function. When enabled, the button indicator light will illuminate. If a short circuit or overcurrent occurs in the load, the machine will stop output and issue an alarm. Pressing the OUTPUT button or the OCP button will deactivate the alarm and shut off the power output. (The machine determines whether a short circuit exists by checking if the output current exceeds the user-set current. Therefore, the machine cannot be used in constant current CC mode when the OCP short-circuit protection function is enabled.)

7.7 OVP Over Voltage Protection Switch

Press the OVP button to enable/disable the OVP overvoltage protection function. When enabled, the button light will illuminate. When an overvoltage occurs, the machine will stop outputting and issue an alarm. Pressing the OUTPUT button or the OVP button will deactivate the alarm and turn off the power output.

  • OVP Parameter Setting Method: Press and hold the OVP button for 3 seconds to enter the OVP parameter setting interface (you will hear two "beep" sounds). Use the VOLTAGE knob to adjust to the desired voltage protection value. After modification, press and hold the OVP button for 3 seconds within 8 seconds to save the settings (you will hear two "beep" sounds). If you do not save within 8 seconds, the settings will be automatically exited without saving.
Excellent safety performance with OCP and OVP
Figure 8: Excellent safety performance. OCP (Overcurrent Protection): When the load is short-circuited or the load current exceeds the set output current, the power supply will be cut off and a buzzer alarm will sound. OVP (Overvoltage Protection): When the actual output voltage is higher than the voltage set by the power supply OVP, the power supply will be cut off and a buzzer alarm will sound.

7.8 Buzzer Switch

Press the buzzer button to turn the buzzer on or off.

7.9 OUTPUT Output Switch

Press the OUTPUT button to turn the power output on or off.

7.10 OPN Function (Output Power ON/OFF on startup)

The OPN function controls whether the OUTPUT button is ON or OFF each time the device is powered on.

  • How to enable/disable the OPN function: With the OUTPUT button OFF, press and hold the OUTPUT button for 3 seconds to enter the settings interface (you will hear two "beep" sounds). Press the OUTPUT button or rotate the VOLTAGE/CURRENT knob to select whether the OPN function is on or off. After making your selection, press and hold the OUTPUT button for 3 seconds to save and exit (you will hear two "beep" sounds).

7.11 USB Fast Charging Function

This device features USB fast charging and has a built-in multi-protocol fast charging identification chip, with a maximum output power of 18W.

USB & Type-C Fast Charging
Figure 9: USB & Type-C Fast Charging. Variable power built-in fast charging protocol recognition chip (18W USB-A, 18W USB-C, QC3.0).

7.12 Host Computer Communication (Optional)

Users can choose models equipped with USB / RS-232 / RS485 communication modules to communicate with a host computer via the MODBUS protocol, enabling remote control.

  • RS-485 Address Setting Method: Press and hold the VOLTAGE knob for 3 seconds to enter the address setting interface. Adjust the VOLTAGE knob to set the RS-485 address. After setting, press and hold the VOLTAGE knob to save and exit.

8. Maintenance

8.1 Regular Inspection, Cleaning, and Maintenance

Regular inspection, cleaning, and maintenance of the machine can help extend its lifespan. Please follow these steps:

  1. Turn off the power switch and unplug the power cord from the socket.
  2. Gently wipe the casing, top cover, and vents with a soft cloth and mild detergent.
  3. Visually inspect all power cords and terminals for damage such as impact, loosening, heat corrosion, moisture, or insect bites. Replace any damaged power cords or terminals with those of the same specifications and dimensions.

8.2 Replace Fuse

If the fuse blows, the machine will stop working. Find and correct the cause of the blown fuse before replacing it with a fuse of the same specifications.

Fuse Replacement Diagram
Figure 10: Fuse Replacement. First, unplug the power cord, then open the fuse holder as shown in the diagram. After replacing the fuse with one of the same model and specifications, reinsert the fuse holder. The fuse holder is located on the power outlet. (Note: Specific image URL for fuse replacement diagram was not provided in ALLOWED_URLS, so a placeholder is used. Please refer to the physical product or original manual for the exact diagram.)

High Volt Danger:

For effective safety protection, only fuses of specific specifications should be replaced. Do not unplug the power cord before replacing the fuse.

9. Troubleshooting

This section provides guidance for common issues. For problems not listed here, please contact customer support.

  • No Output / Power Off: Check if the power cord is securely connected and the power switch is ON. Verify the AC input voltage matches the machine's requirements. If the unit is completely unresponsive, check the fuse.
  • Alarm Sounding: An alarm indicates a protection event (OCP or OVP). Identify the cause (short circuit, overcurrent, or overvoltage) and resolve it. Press the OUTPUT button or the corresponding protection button (OCP/OVP) to deactivate the alarm and reset the output.
  • Output Voltage/Current Unstable: Ensure proper grounding. Check load connections for secure contact. Verify that the load resistance is appropriate for the set voltage/current.
  • Controls Unresponsive: Check if the Button Lock Switch (LOCK) is engaged. If the LOCK indicator light is on, press the LOCK button to unlock the controls.
  • Incorrect Parameter Storage/Recall: Review the memory storage and recall procedure (Section 7.5). Ensure you press and hold the MEMORY button for 3 seconds to enter/save settings and save within 8 seconds.

10. User Tips

  • Pre-set Frequently Used Values: Utilize the 4 memory groups (M1-M4) to store common voltage and current settings for quick recall, saving time during repetitive tasks.
  • Engage Output Lock: When performing sensitive work or leaving the power supply unattended, use the 'LOCK' function to prevent accidental changes to output parameters.
  • Monitor Protection Indicators: Pay attention to the OCP and OVP indicator lights. If they illuminate or an alarm sounds, immediately check your circuit for short circuits, overcurrents, or overvoltages to prevent damage.
  • Proper Ventilation: Ensure the cooling fan on the back panel is not obstructed to maintain optimal operating temperature and prolong the lifespan of the device.
  • Use Fast Charging Ports: The integrated USB-A and USB-C ports are convenient for charging compatible devices directly from the power supply, reducing clutter on your workbench.

11. Warranty & Support

11.1 Product Inspection

Each product comes with an instruction manual and a certificate of conformity to ensure correct usage. All products manufactured and inspected by our company are produced and inspected according to manufacturer's standards; any unqualified products will never leave the factory.

11.2 Product Warranty

A one-year warranty is provided, excluding damage caused by human error.

11.3 Product Repair

  • Free repair or replacement of parts is provided during the warranty period. After the warranty period, paid repair services are available.
  • During the product's service life, if the product malfunctions, the company is only responsible for the malfunction and loss of the product itself; the company does not bear any load or other related losses.

Guarantee Limitations:

The warranty does not apply to losses caused by the following circumstances:

  1. Customer violation of the usage instructions in this manual
  2. Customer disassembly or repair of the product
  3. Unauthorized modifications or misuse
  4. Operation of the product outside the specified environment
  5. Force majeure factors under relevant laws

11.4 Packing List

  • Main unit x1
  • Power cord x1
  • Output load cable x1
  • User manual x1
  • Warranty card and certificate of conformity x1

12. Contact Information

Shenzhen Toviyon Electronics Technology Co., Ltd.

Address: Room 203, 2nd Floor, No. 69, Langkou Industrial Park, Langkou Community, Dalang Subdistrict, Longhua District, Shenzhen

Web: www.toviyon.com

Tel: (+86)18588483965

WhatsApp: +1(424)413-3536

WeChat: 18588483965

QR code to follow Toviyon Power for more services
Figure 11: Scan to follow Toviyon Power for more services on our official website. (Note: Specific image URL for QR code was not provided in ALLOWED_URLS, so a placeholder is used. Please refer to the physical product or original manual for the exact QR code.)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.