Speras EST MIC

Contents

Speras EST MIC EDC 700 Lumen Flashlight

User Manual

1. Introduction

The Speras EST MIC is a compact and powerful EDC (Everyday Carry) flashlight designed for versatile use. It features a Luminus SST12 LED, delivering up to 700 lumens, powered by a rechargeable 10440 lithium-ion battery. This manual provides essential information for the safe and effective use of your flashlight.

Speras EST MIC Flashlight Overview

Figure 1: Speras EST MIC Flashlight highlighting key features: 700 lumens, 138m beam distance, USB-C charging, and 50 hours max runtime.

2. Package Contents

Please check the package for the following items:

  • 1x Speras EST MIC Flashlight
  • 1x 10440mAh Lithium-ion Battery
  • 1x Type-C Charging Cable
  • 2x Spare O-rings
  • 1x User Manual (this document)
Speras EST MIC Package Contents

Figure 2: Contents included in the Speras EST MIC flashlight package.

3. Setup and First Use

Important: The insulation tab inside the new battery compartment MUST be removed before installing batteries.

3.1. Installation Steps

  1. Open the Battery Compartment: Rotate the tail cap (or head) counter-clockwise to unscrew it.
  2. Remove the Insulation Tab: Locate and remove the colored plastic insulating tab from the battery compartment. This step is mandatory for the flashlight to function.
  3. Install Batteries Correctly: Check the polarity symbols inside the tube. The battery's positive (+) end usually faces the head, and the negative (-) end faces the tail cap.
  4. Reassemble: After reinserting the battery, align the back cover with the threads and turn it clockwise until you feel a slight resistance and it is snug (do not over-tighten).

4. Operating Instructions

4.1. Charging

The EST MIC features a hidden USB-C charging port. To access it, unscrew the head slightly. The charging indicator light will show:

  • Red: Charging
  • Green: Fully charged
Hidden USB-C Port Design and Charging Indicators

Figure 3: Hidden USB-C charging port and its charging status indicators.

4.2. Turning On/Off and Mode Switching

The EST MIC offers multiple ways to control illumination:

  • Twist Switch: Fully tighten the head or tail cap to turn ON. Loosen about half a turn counter-clockwise to turn OFF.
  • Tail Click Switch: Press the tail button to turn ON/OFF. A light press provides momentary ON; a full click locks it ON for continuous illumination.
  • Side Switch (if applicable): Press the electronic switch on the body.

Mode Switching: Rapidly short-press the power button (tail or side switch) to cycle through different brightness modes (High-Medium-Low) and special modes (Strobe, SOS).

Flashlight Modes in Use

Figure 4: Examples of High, Medium, and Low light modes in various scenarios.

4.3. Two-Way Clip Functionality

The included two-way clip allows for versatile attachment, enabling hands-free lighting. It can be securely attached to backpack straps, hat brims, or pockets.

Two-Way Clip for Hands-Free Lighting

Figure 5: The two-way clip allows the EST MIC to be used as a headlamp for hands-free illumination.

5. Maintenance and Safety

5.1. Battery Care

  • Use only the specified 10440 lithium-ion battery. Do not mix old and new batteries, or batteries of different brands/types.
  • Lithium-ion batteries self-discharge. If the flashlight will not be used for an extended period, remove the battery and recharge it at least once every 2-3 months.

5.2. Water Resistance

The EST MIC has an IP68 waterproof rating. Ensure O-rings are clean and all components are tightly screwed to maintain water resistance. Do not submerge non-diving flashlights deeply for prolonged periods.

5.3. Cleaning

Clean the lens and body with a soft, dry cloth. Avoid using corrosive chemicals.

5.4. Heat Dissipation

Using the high-brightness mode for an extended period will cause the lamp head to heat up, which is normal. To protect the LED and ensure longevity, it is recommended to use high mode intermittently.

5.5. Safety Precautions

  • Never point the light directly or indirectly at eyes or skin when it is on, as this may cause vision impairment or skin burns.
  • Keep out of reach of children.

6. Troubleshooting

6.1. No Light

  • Check if the insulation tab has been removed.
  • Ensure batteries are installed with correct polarity.
  • Verify batteries are not exhausted; try recharging or replacing.
  • Confirm all parts (tail cap, head) are tightened securely.

6.2. Light Dims or Flickers

  • Battery may be low on power; recharge or replace with a new one.
  • Check the switch or circuit; try reinstalling the battery.
  • A slight glow from the tail is a characteristic of some electronic switch circuits and is not a defect. Loosening the tail cap slightly may stop it.

7. Specifications

Speras EST MIC Detailed Specifications

Figure 6: Detailed specifications and dimensions of the Speras EST MIC flashlight.

FeatureHigh (White)MediumLow
Output700 LM100 LM5 LM
Runtime1.2 H2 H50 H
Beam Intensity4,770 cd1,080 cd-
Beam Distance138 m66 m-
General Specifications
LED1* Luminus SST12
LensPMMA + PC
Battery Source1* 10440 350mAh
Impact Resistance1 m
Waterproof RatingIP68
Body MaterialAerospace 6061 Aluminum Alloy
FinishPremium Type III Hard-anodizing
Dimensions (L*Head*Tube)89.2 mm * 11.4 mm * 9.9 mm
Net Weight27.8 g (excluding battery)
ChargerRechargeable (USB-C)
CertificationCE, ROHS

8. User Tips

  • For optimal performance, ensure the battery is fully charged before extended use.
  • Utilize the two-way clip for hands-free operation during camping, hiking, or tasks requiring both hands.
  • Regularly check and clean the O-rings to maintain the flashlight's IP68 waterproof rating.

9. Warranty and Support

For warranty information or technical support, please contact your original point of purchase or the official Speras customer service. Keep your purchase receipt as proof of purchase.

© 2024 Speras. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.