1. Introduction
Thank you for choosing the YTYIN Front Trunk Ambient Light Strip. This product is designed to enhance the lighting and ambiance of your Tesla Model 3 or Model Y's front trunk (frunk). This manual provides essential information for safe installation, operation, and maintenance of your new light strip.
2. Safety & Warnings
Please read all instructions carefully before installation and use. Failure to follow these instructions may result in product damage or personal injury.
- Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- Do not expose to water or moisture beyond its IP67 rating.
- Handle with care to avoid cuts or injuries.
3. Package Contents
Please verify that all items are present in your package:
- 1x Flexible LED Light Strip (Warm White)
- 1x Connection Cable / Wiring Harness

Image: Contents of the YTYIN Frunk LED Light Strip kit, showing the coiled light strip, wiring, and an example of the installed light.
4. Setup & Installation
The YTYIN Front Trunk Ambient Light Strip is designed for a simple plug-and-play installation that does not interfere with your vehicle's original wiring.
- Prepare the Frunk: Open the front trunk of your Tesla Model 3 or Model Y. Identify the area where you wish to install the LED strip. Ensure the surface is clean and dry for optimal adhesion.
- Connect the Wiring: Locate the existing power connector or light fixture within the frunk. Connect the provided wiring harness to this point. The connection is designed to be plug-and-play, matching the original car plug.

Image: Close-up view of the plug-and-play connection point within the frunk.
- Position the LED Strip: Carefully route the LED strip along the desired edge of the frunk. The strip is flexible and can be bent to follow contours.
- Secure the Strip: Remove the adhesive backing from the LED strip (if applicable) and firmly press it into place along the chosen path. Ensure it is securely attached and neatly positioned.

Image: Four-panel diagram illustrating the step-by-step installation process of connecting the wiring and adhering the LED strip in the frunk.

Image: Comparison showing the frunk with limited lighting before installation and with even, atmospheric lighting after the LED strip is installed.
5. Operation
The YTYIN Front Trunk Ambient Light Strip operates automatically:
- The light strip will illuminate automatically when the front trunk is opened.
- To conserve power, the light strip will automatically shut off approximately 10 minutes after the front trunk is closed.
6. Maintenance & Storage
- Cleaning: Ensure the vehicle's power is off or the light strip is disconnected before cleaning. Use a soft, lint-free cloth to gently wipe the LED strip. Do not use abrasive cleaners or solvents.
- Storage: If the light strip is removed from the vehicle, store it in a dry place at room temperature (15°C - 35°C / 59°F - 95°F), away from direct sunlight or extreme temperatures.
7. Troubleshooting
If the product does not function as expected, please refer to the following:
- Light not turning on:
- Check that all connectors are securely plugged in.
- Ensure the vehicle's 12V power source in the frunk is active.
- Inspect the LED strip and wiring for any visible damage.
- Light flickering:
- Verify all connections are tight and secure.
- Ensure a stable power supply from the vehicle.
- General Safety: Stop using the product immediately if you observe any abnormal heat, smell, smoke, deformation, or unusual noise.
8. Specifications
| Brand | YTYIN |
| Product Type | Atmosphere Lamp / LED Light Strip |
| Compatibility | Tesla Model 3 (2021+), Tesla Model Y (2021+) |
| Voltage | 12V (compatible with 12V-16V vehicle systems) |
| Power Consumption | 6W/Meter |
| Length | 270 cm (can be cut) |
| Waterproof Rating | IP67 |
| Material | Silicone (light strip), ABS (connectors) |
| Item Weight | 0.16 kg |
| Certifications | CE |

Image: Diagram highlighting key specifications: 12V/16V current protection, 6W/M consumption, IP67 waterproof, and flexible silicone LED light strip.

Image: The coiled LED strip submerged in water, illustrating its IP67 waterproof capability.
9. Compliance & Disposal
- Disposal: Do not dispose of this product with general household waste. This product contains electronic components and should be disposed of according to local environmental regulations. Please consult your local authorities for proper recycling and disposal options.
- Certifications: This product complies with CE standards.