DB-302 DB-302

Contents

Smart Robot Vacuum Cleaner

Model: DB-302

User Manual

1. Safety Instructions

1.1 General Safety Precautions

  • Do not use this product in environments with temperatures higher than normal operating conditions.
  • Always use the product with a protective fence to prevent drops caused by complex reasons.
  • Before using, please read this manual carefully and adhere to all safety precautions. Keep the manual for future reference.

1.2 Product Safety Warnings

WARNING:

Use only the original adapter. Using other adapters may cause product damage, electric shock, or fire due to high voltage.

Place the charging dock along a wall and ensure there are no obstacles within 2 meters in front of or around the station.

Diagram showing correct placement of charging dock and obstacles to avoid

Image: Diagram showing the robot vacuum and its charging dock, indicating a 2-meter clearance area in front and 1-meter around the dock.

If the main unit or accessories are damaged, do not use the unit. Contact the professional after-sales service department.

Do not touch the power plug or unit with wet hands, as this may cause electric shock.

Diagram showing a damaged robot vacuum with an 'X' mark, indicating not to use it

Image: Illustration of a damaged robot vacuum with a red 'X' over it, and a hand touching a plug with a red 'X', emphasizing not to use damaged units or touch with wet hands.

Do not use this product without a protective fence to avoid drops. Do not bend the power line or use it to move the unit. Do not place anything on the power line.

Diagram showing a robot vacuum near a drop-off with an 'X' and a bent power cord with an 'X'

Image: Illustrations showing a robot vacuum near a ledge with a red 'X' and a power cord being bent with a red 'X', indicating improper use.

Do not place the unit close to fire or flammable materials. Do not put any part of your body into the wheel or brush, as this may cause injury.

Diagram showing a robot vacuum near fire with an 'X' and a hand near the brush with an 'X'

Image: Illustrations showing a robot vacuum near flames with a red 'X' and a hand near the rotating brush with a red 'X', indicating fire hazard and risk of injury.

1.3 Cautions

ONLY USE INDOOR.

Diagram showing robot vacuum indoors with a checkmark and outdoors with an 'X'

Image: Illustration showing the robot vacuum operating indoors (checkmark) and an 'X' over an outdoor scene, indicating indoor use only.

Avoid sucking water, oil, and other liquids that may damage the vacuum cleaner.

Diagram showing robot vacuum avoiding liquids with an 'X'

Image: Illustration of the robot vacuum with a red 'X' over liquids, indicating not to vacuum liquids.

Clear power lines on the ground to avoid affecting unit operation.

Diagram showing a clear power line with a checkmark and a tangled one with an 'X'

Image: Illustration showing a power cord on the floor with a red 'X' over it, indicating to clear power lines.

1.4 Children Safety

  • Prohibit children from using the unit alone.
  • Prohibit children from playing with the unit's bag, as it may cause suffocation.

1.5 Battery Safety

  • Use only the original battery.
  • Remove the battery when discarding the unit.
  • Contact the after-sales service department if you need to change the battery.
  • Use a dry cloth to clean if there is battery leakage.

2. Setup

2.1 Packing List

The package includes the following components:

Contents of the product package including the robot vacuum, charging station, adapter, manual, side brushes, remote, mop towel, and filter.

Image: Contents of the product package laid out, including the robot vacuum, charging station, adapter, manual, side brushes, remote, mop towel, and filter.

No.DescriptionQuantity
1Main Unit (includes battery)1
2Charge Station1
3Adapter1
4Manual1
5Filter1
6Side Brush2
7Remote1
8Mop Towel1

★ REMIND: The battery has been installed in the unit.

2.2 Product Overview

Front Side View:

  • Collision Bumper
  • Start Button
  • Cover (to access dustbin)
Front view of the robot vacuum showing collision bumper and start button

Image: Front view diagram of the robot vacuum, highlighting the collision bumper, start button, and the cover for the dustbin.

Back Side View:

  • Universal Wheel
  • Left Side Brush
  • Inlet
  • Left Side Drive Wheel
  • Right Side Brush
  • Right Side Drive Wheel
  • Three Anti-Drop Sensors
Underside view of the robot vacuum showing brushes, wheels, and sensors

Image: Underside view diagram of the robot vacuum, showing the universal wheel, side brushes, inlet, drive wheels, and anti-drop sensors.

2.3 Inside Structure & Charging Station

Inside Structure (Dustbin):

  • Cover
  • Cover of Dustbin
  • Filter
  • Dustbin
  • Dustbin Position
Diagram of the robot vacuum's internal dustbin components

Image: Diagram illustrating the internal components related to the dustbin, including the cover, filter, and dustbin itself.

Charging Station:

  • Power Adapter
  • Power Connection
  • Recharge Pin (x2)
Diagram of the charging station and its connections

Image: Diagram of the charging station, showing the power adapter, power connection, and recharge pins.

2.4 Assemble Dustbin and Install Side Brush

Assemble Dustbin:

  1. Open the cover of the robot.
  2. Pull the handle of the dustbin to remove it.
  3. To install, slide the dustbin back into its position until it clicks.

Install Mop Towel:

  1. Attach the mop towel to the bottom of the unit using the magic stickers.
Diagram showing how to assemble the dustbin and install the mop towel

Image: Diagrams illustrating the assembly of the dustbin (pulling by handle) and the installation of the mop towel using magic stickers.

Install Side Brush:

  1. Take out the side brushes and press them into the brush position until they lock.
  2. To detach, catch the brush and pull it out by force.

★ REMIND: Please check if the side brush is locked before every use.

Diagram showing installation and removal of side brushes

Image: Diagrams showing the installation of side brushes by pressing them into place and removal by pulling them out.

3. Operation

* ATTENTION: Before using, please remove any protection blocks and clear obstacles in the room.

3.1 Scope of Application

The product is suitable for various floor types:

Wood Floor

Wood Floor

Carpet

Carpet

Ceramic Tile

Ceramic Tile

The product is NOT suitable for:

  • Environments with temperatures less than 10 degrees Celsius or higher than 60 degrees Celsius.
  • Outdoor use (ONLY USE INDOOR).
  • Use without a protective fence to avoid drops.
  • Sucking powder from printers or copiers.
  • Sucking sharp objects like glass, steel, etc.

3.2 Operation Status

1. OFF Status:

When the unit is in the OFF status, press the power button. After one buzzer sound, the blue light will turn on, and the unit will enter standby after 3 seconds.

Diagram showing OFF status to Standby status transition

Image: Diagram illustrating the transition from OFF status to Standby status by pressing the power button.

2. Standby Status:

When the unit is in standby status, the blue light is always on.

  • The unit will automatically turn off if there is no operation within 5 minutes.
  • Short press the power button: One buzzer sound, the unit will enter automatic cleaning mode.
  • Short press the home button: One buzzer sound, the unit will enter dock recharge mode.
  • Long press the power button: One buzzer sound, the unit will turn off.
  • Plug into the socket: One buzzer sound, the unit will enter recharge status.

3.3 Remote Control Functions

Remote control with various buttons

Image: Illustration of the remote control with its buttons for various functions.

  1. Power Button (on remote): When the machine is off, long press to start the machine. It will enter standby status with one buzzer sound. Long press again in standby status to turn off the machine.
  2. Home Button (on remote): Press to make the machine find the recharge station and dock for recharge.
  3. Turbo Button: Press once to adjust suction to lower. Press again to adjust to higher suction. (Two gears)
  4. Wall Button: Press to make the machine enter edge cleaning mode, cleaning along edges.
  5. Spot Button: Press to make the machine enter spot cleaning mode, cleaning in a rotary type as the current position as center.
  6. Up Button: Press to move the machine forward.
  7. Left Button: Press to turn the machine left and move.
  8. Down Button: Press to move the machine backward.
  9. Right Button: Press to turn the machine right and move.
  10. Full Go Button: When the machine is on the recharge station, long press this button for 2 seconds. The machine will buzz twice, automatically clean after full charge, and return to recharge once power is low.
  11. Timer Button: When the machine is on the recharge station, long press this button for 2 seconds. The buzzer sounds twice, and the machine will turn to reserve auto clean mode, cleaning automatically after 24 hours. If any other button is pressed to make the machine leave the station during this period, the timer function will be canceled.
  12. Start/Stop Button (on unit): At standby status, press to start auto clean. Press again to stop cleaning.

3.4 Automatic Cleaning Mode

In automatic mode, the blue light on the unit is illuminated. This function is suitable for full house cleaning. The robot will clean in a zigzag pattern with anti-collision and anti-drop features, automatically avoiding obstacles and stairs.

3.5 Dock Automatic Recharge Mode

During dock automatic recharge mode, the blue light will slow flash. The machine will search for the recharge station. Once found, it will automatically recharge. The motor is off during the searching period.

3.6 Change Machine Operation Status

  1. Press the power button or home button. One buzzer sound, the machine will turn to standby mode.
  2. When the machine has trouble, it will provide a warning.

4. Recharge

4.1 Recharge Station Placement

It is suggested to place the recharge station in a flat place along a wall. Do not place obstacles within 2 meters in front of the station and 1 meter around it.

Diagram showing optimal placement for the charging dock with clearance measurements

Image: Diagram illustrating the recommended placement of the charging dock against a wall, with a 2-meter clearance in front and 1-meter clearance on the sides.

4.2 Dock Automatic Recharge

If the power is low during operation, the unit will automatically search for the recharge station. Once found, it will automatically recharge.

You can also press the home button on the unit or remote control, and the machine will search for the recharge station automatically. Once found, it will automatically recharge.

4.3 Manual Recharge

Connect the adapter with the machine and plug it into a power outlet.

Diagram showing how to manually recharge the robot vacuum

Image: Diagram showing the manual charging process by directly plugging the adapter into the robot vacuum.

4.4 Initial Charge and Storage

  1. Please charge for 12 hours for the first time.
  2. For normal use, place the machine on the recharge station and ensure the station is plugged into the socket.
  3. If the machine will not be used for a long time, fully charge it, turn it off, and store it in a dry place.

4.5 Recharge Status Indicator

During recharge, the blue and violet lights will alternately flash. Once fully recharged, the violet light will remain continuously on.

During recharge, if you press the power button, the machine will leave the recharge station and turn to auto-clean mode.

5. Maintenance

5.1 Clean Side Brush

Please clean the side brush when it gets dirty.

5.2 Clean Dustbin and Filter

Clean the dustbin and filter after every use as follows:

Sequence of steps to clean the dustbin and filter

Image: A series of diagrams (A-G) illustrating the steps to remove, empty, and clean the dustbin and filter.

★ REMIND: Please check if there is anything blocking the inlet mouth and clean it.

5.3 Clean Sensor and Recharge Connect Pins

Use a soft towel to clean the sensors and recharge connect pins.

Diagram showing locations of sensors and recharge pins for cleaning

Image: Diagram highlighting the locations of the sensors and recharge connect pins on the robot vacuum and charging station for cleaning.

6. Troubleshooting

This section provides solutions for common issues indicated by the trouble light flash times.

No.Trouble Light Flash TimeTrouble DescriptionSolution
12 flashesLow PowerRecharge or change battery
23 flashesUnusual CollisionCheck if there is something in the bumper
34 flashesUnusual Anti-Drop1. Check if there is something in the sensor lamp.
2. Check if the sensor line is off.
3. Infrared sensor problem.

7. Specifications

FeatureDetail
Model No.DB-302
Voltage7.4V
Rated Power10W
BatteryLI, 2000MAH
Recharge TimeAbout 5 hours
Working Time≥90 minutes
Dustbin Capacity430ML
Noise Level≤65DB
Product SizeØ 315*81MM
Diagram showing the dimensions of the robot vacuum: 31.5cm (12.4in) diameter and 6.2cm (2.4in) height.

Image: Diagram showing the dimensions of the robot vacuum: 31.5cm (12.4in) diameter and 6.2cm (2.4in) height.

8. User Tips

No specific user tips are available from provided reviews or Q&A content.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the contact information provided by your retailer or the manufacturer's official website. Keep your purchase receipt as proof of purchase.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.