Voktta BTS04AL

Contents

Voktta BTS04 Series Lithium Battery Tester User Manual

Model: BTS04AL

1. Safety Requirements

1.1 General Safety Overview

To prevent injury and product damage, please read and understand the following safety precautions. Always use this product as specified.

1.2 Check Terminal Ratings

To avoid fire or excessive current, check all ratings and markings on the product. Consult the product manual for detailed information before connecting.

1.3 Use Appropriate Overvoltage Protection

Ensure no overvoltage (e.g., lightning-induced voltage) reaches the product to prevent electric shock.

1.4 Do Not Operate with Open Casing

Do not operate the product with its casing open.

1.5 Do Not Insert Foreign Objects into Heat Dissipation Vents

Inserting foreign objects into the heat dissipation vents may damage the instrument.

1.6 Avoid Exposed Circuits

Do not touch exposed terminals or components when the power is connected.

1.7 If Malfunction is Suspected, Do Not Operate

If you suspect a malfunction, contact JUNCTEK authorized service personnel for inspection. All maintenance, adjustments, or parts replacement must be performed by JUNCTEK authorized personnel.

1.8 Maintain Adequate Ventilation

Poor ventilation can cause the instrument to overheat and damage it. Ensure good ventilation during use and regularly check the vents.

1.9 Do Not Operate in Humid Environments

To prevent short circuits or electric shock, do not operate the instrument in humid environments.

1.10 Do Not Operate in Flammable or Explosive Environments

To prevent instrument damage or personal injury, do not operate in flammable or explosive environments.

1.11 Keep Product Surface Clean and Dry

To prevent dust or moisture from affecting instrument performance, keep the product surface clean and dry.

1.12 ESD Protection

Electrostatic discharge can damage the instrument. Test in an ESD-protected area whenever possible. Before connecting cables to the instrument, briefly ground their inner and outer conductors to release static electricity.

1.13 Handling Safety

To prevent damage to buttons, knobs, or interfaces on the instrument panel due to dropping during handling, please handle with care.

1.14 Care and Maintenance

  1. Do not exceed the instrument's voltage and current ranges, as this will damage the instrument.
  2. Do not reverse the positive and negative terminals; incorrect connection cannot be processed correctly.
  3. The instrument casing is fragile and susceptible to corrosion. Avoid violent impacts and contact with chemicals.
  4. Store at temperatures between -10~50℃ in a dry environment.
  5. Do not attempt to disassemble this instrument; breaking the seal will void the warranty. There are no user-serviceable parts inside. Repairs must be performed by authorized service centers or by returning the unit to the manufacturer.
  6. Avoid placing lit candles, water-filled cups, corrosive chemicals, or other unsafe items on the instrument surface to prevent damage.
  7. The display screen is sensitive and fragile. Do not touch or bump it with hands or other objects. Keep children from playing with the instrument. If the LCD surface is dusty, gently wipe it with a soft cloth.
  8. Do not move the instrument violently during normal operation to avoid irreparable damage to internal circuits. If the instrument still does not work properly after troubleshooting and re-powering, please contact your supplier.

2. Product Overview

2.1 Introduction

The BTS04 series battery tester is a 4-channel testing device specifically designed for 18650 batteries, offering high precision and versatile testing capabilities. This series supports testing of both lithium and LiFePO4 batteries, with standard and Bluetooth-enabled versions available to meet diverse user needs.

2.2 Key Features

  • High-Precision Detection: Accurate measurement of battery voltage, current, capacity, energy, and internal resistance.
  • Three Operating Modes: Supports Charging Mode, Discharging Mode, and Cycling Mode for flexible operation.
  • Fan Cooling: Built-in high-speed fan with a vented design for intelligent, efficient rapid heat dissipation.
  • Multi-Layer Protection: Includes reverse polarity protection, overcharge protection, over-discharge protection, and temperature control protection.
  • Multi-Interface Display: Provides List interface, Single-Channel interface, Results interface, and Curve interface for comprehensive data visualization.
  • Energy Recovery & Reuse: Innovative energy recycling technology converts discharged energy into charging energy for other channels, improving efficiency and reducing waste.
  • Mobile App & PC Software Control: Bluetooth connectivity for Android/iOS app control and dedicated PC software for advanced data analysis and remote monitoring.

2.3 Technical Specifications

ParameterSpecification
Model NumberBTS04AL (Standard Edition), BTS04BL (BT Edition), BTS04CL (BT Large Memory Edition)
Suitable Battery Types3.7V Lithium batteries (BTS04AL/BL/CL), 3.2V LiFePO4 batteries (BTS04AF/BF/CF)
Voltage Resolution0.001V
Current Resolution0.001A
Capacity Range0000-9000Ah
Capacity Resolution0.001Ah
Energy Range0000-9000Wh
Energy Resolution0.001Wh
Internal Resistance Range0000-9999mΩ
Internal Resistance Resolution1mΩ
Operating Time00:00:00-99:59:9
Operating ModesSingle Charge, Single Discharge, Cycle Mode
Current RangesLow Current 0.6A, High Current 1A
Cycle Test1-9 cycles
Cycle Switching Time1-60s
Standby Power Consumption0.65W
Screen Brightness1-100%
Auto-off TimeOFF, 10-120s
Power Supply12V 2A
Product Dimensions190mm (L) x 129mm (W) x 32mm (H)

2.4 Applicable Battery Types

The BTS04 series is compatible with a wide range of cylindrical batteries and polymer pouch cells, including:

  • 10400
  • 14500
  • 16340
  • 18650
  • 21700
  • 26650
  • Polymer Pouch Cells
Bar chart showing compatibility with various battery types: 10400, 14500, 16340, 18650, 21700, 26650, and Polymer Pouch Cells.
Figure 2.4.1: Compatibility with Multiple Battery Types

3. Package Contents

Upon receiving your new BTS04 series battery tester, please follow these steps to inspect the package and its contents:

3.1 Inspect Shipping Packaging

If the shipping packaging is damaged, retain the damaged packaging or shock-absorbing materials until the goods have been fully inspected and the instrument has passed electrical and mechanical tests. If instrument damage is caused by shipping, contact the shipper and carrier for compensation.

3.2 Check Included Accessories

The package should contain the following items. If any content is missing or the instrument is damaged, please contact your dealer or our company.

ItemQuantity
Main Unit (BTS04 Series Battery Tester)1 unit
12V3A Power Adapter1 piece
User Manual (Quick Start Guide)1 copy
2-pin Green Terminal4 pieces
Type-C Data Cable1 piece
Image showing the BTS04 main unit, Type-C data cable, user manual, 2-pin green terminals, and charger.
Figure 3.2.1: Packing List
Main product image of the BTS04 Lithium Battery Capacity Tester with four 18650 batteries inserted, along with its accessories.
Figure 3.2.2: BTS04 Lithium Battery Capacity Tester and Accessories

4. Device Layout

Diagram of the BTS04 series product, showing the front panel with LCD, silicone buttons, channel indicator lights, battery slots, cooling fan, 12V3A power input, Type-C communication port, and expansion interface.
Figure 4.1.1: BTS04 Series Product Diagram
No.DescriptionNo.Description
1LCD Display5Cooling Fan
2Silicone Buttons612V3A Power Input
3Channel Indicator Lights7Type-C Communication Port
4Battery Slots8Expansion Interface

4.1 LCD Display

Equipped with a 2.8-inch color LCD screen, it clearly displays the current function menu and parameter settings.

4.2 Silicone Buttons

  • [SET] Button: Short press to quickly enter the settings interface.
  • [DTLS] Button: Primarily used for single-channel interface operations.
  • [▲] Button: Used for channel switching, function switching, and value adjustment.
  • [RSLT] Button: Press to enter the results list interface.
  • [CURVE] Button: Used to enter the voltage-mAh curve interface.
  • [CLR] Button: Functions as a data clear button to erase relevant data.
  • [◀] Button: Used for mode selection and numerical digit switching.
  • [▼] Button: Used for channel switching, function switching, and numerical value adjustment.
  • [▶] Button: Used for mode selection and numerical digit switching.
  • [OK] Button: Serves as a confirmation button and can also be used as an output switch.

4.3 Channel Indicator Lights

There are four channel indicator lights. A green light indicates the corresponding channel is charging; a blue light indicates the corresponding channel is discharging.

4.4 Battery Slots

Insert the battery to be tested correctly according to the positive and negative indications in the battery slot.

4.5 Cooling Fan

Its main function is to dissipate heat from the device, ensuring normal operation.

4.6 12V3A Power Input

Used to provide power to the device.

4.7 Type-C Communication Port

Serves as a communication interface for connecting to a PC, enabling data transmission between the device and the PC.

4.8 Expansion Interface

Can be used to connect other types of batteries, expanding the device's application range.

5. Basic Operation

The BTS04 series offers multiple display interfaces to monitor and manage battery testing. These include the List Interface, Single-Channel Interface, Results Interface, and Curve Interface.

5.1 List Interface Operation

The list interface allows you to monitor multiple channels simultaneously for improved efficiency.

List interface display showing real-time data for four battery channels, including voltage, capacity, internal resistance, and operating time.
Figure 5.1.1: List Interface Schematic Diagram
No.DescriptionNo.Description
1Channel6Current
2Output Switch7Battery Capacity
3Charge/Discharge Status8Battery Energy
4Mode9Internal Resistance
5Battery Voltage10Operating Time

5.1.1 Channel Selection

Use the [▲] and [▼] buttons to switch between channels 1, 2, 3, and 4. The selected channel will be highlighted with a yellow indicator light.

5.1.2 Mode Switching

Press the [◀] button to switch between Loop (Cycle Mode), CHG (Charge Mode), and DIS (Discharge Mode).

5.1.3 Charge/Discharge Current Gear Switching

Use the [▶] button to switch between High Current (large current gear) and Low Current (small current gear).

5.1.4 Start Charging or Discharging

Press the [OK] button to start charging or discharging the battery.

5.1.5 Data Clearing

Press the [CLR] button to clear the data in the current storage space.

5.2 Single-Channel Interface Operation

The single-channel interface focuses on one channel for in-depth performance analysis.

Single-channel interface display showing detailed parameters for a single battery, including voltage, current, power, internal resistance, capacity, energy, and operating time.
Figure 5.2.1: Single-Channel Interface Schematic Diagram
No.DescriptionNo.Description
1Channel7Operating Time
2Mode8Discharge Ah
3Voltage9Charge Ah
4Current10Discharge Wh
5Power11Charge Wh
6Internal Resistance12Output Status

5.2.1 Channel Selection

From the list interface, select the channel you want to view (the selected channel will be highlighted in yellow), then short press the [DTLS] button to enter the single-channel interface. In the single-channel interface, use the [▲] and [▼] buttons to switch between different channels.

5.2.2 Mode Switching

Press the [◀] button to switch between Loop (Cycle Mode), CHG (Charge Mode), and DIS (Discharge Mode).

5.2.3 Charge/Discharge Current Gear Switching

Press the [▶] button to switch the current gear between High Current (large current gear) and Low Current (small current gear).

5.2.4 Start Charging or Discharging

Press the [OK] button to start charging or discharging the battery.

5.2.5 Data Clearing

Press the [CLR] button to clear the data in the current storage space.

5.3 Results Interface Operation

The results interface allows you to view each channel's cycle parameters clearly for comparison and analysis.

Results interface showing detailed test results for a battery channel, including voltage, internal resistance, and charge/discharge capacities over multiple cycles.
Figure 5.3.1: Results Interface Schematic Diagram
No.DescriptionNo.Description
1Channel6Cycle Count
2Storage Location7Charge Ah & Wh
3Charge Cut-off Current8Discharge Ah & Wh
4Internal Resistance9End Charge Ah & Wh
5Discharge Cut-off Voltage10End Charge Cut-off Voltage

5.3.1 Viewing Stored Data

Use the [◀] and [▶] buttons to switch between 10 storage locations (M101 - M111). The '*' symbol indicates the current data storage location. You can view the charge and discharge waveforms for each storage location to understand battery status changes.

5.3.2 Channel Selection

Use the [▲] and [▼] buttons to switch between M100, M200, M300, and M400 channels to view corresponding channel data.

5.3.3 Data Clearing

Press the [CLR] button to clear all data in the current storage space, making room for new data records.

5.4 Curve Interface Operation

The curve interface allows you to intuitively understand charging/discharging performance and status.

Curve interface display showing voltage-mAh historical waveform for a battery channel during charging.
Figure 5.4.1: Curve Interface Schematic Diagram
No.DescriptionNo.Description
1Channel4Voltage X-axis
2Storage Location5Ah Y-axis
3Ah Data

5.4.1 Channel Selection

The device has four independent channels (1, 2, 3, 4) that can perform testing simultaneously without interference.

5.4.2 Storage Location

Clearly displays the storage location of current test data, facilitating subsequent data retrieval, analysis, and management.

5.4.3 Ah Data

Real-time recording and display of the total Ah value during battery charging or discharging, intuitively reflecting changes in battery capacity.

5.4.4 Voltage X-axis Value

In the relevant data charts, voltage is positioned as the X-axis to present the trend of voltage changes with other parameters, facilitating visual analysis of battery performance.

5.4.5 Ah Y-axis

In the data charts, Ah data is presented as the Y-axis. Combined with the voltage X-axis, it clearly shows the relationship between Ah and voltage during battery charge and discharge, aiding in in-depth evaluation of battery status.

6. Repair Mode

When the 18650 battery tester is powered on but no battery is inserted, pressing the [CLR] button will bring up a prompt window displaying "Enter Repair Mode". In normal mode, if the battery voltage is below 0.6V, the system will determine it as having no battery, thus preventing charging. For such low-voltage batteries, slow charging repair is required in repair mode.

Screenshots showing the repair mode prompt and the battery repair process. The left image shows a prompt 'CH-1 enters repair mode' with 'No' and 'Yes' options. The right image shows a battery being charged at 0.059A in repair mode.
Figure 6.1.1: Repair Mode Interface

6.1 Exiting Repair Mode

When the channel is in repair mode, short press the [OK] button to exit.

7. System Settings

Users can enter the system settings by short pressing the [SET] button. The first interface entered is the channel settings interface, which corresponds to the selected channel in the list or single-channel interface. Short press the [SET] button again to enter the basic settings interface for the entire instrument.

7.1 Channel Settings Interface

Screenshot of the channel settings interface, showing options for work mode, current level, cycle count, charge cut-off current, discharge cut-off voltage, final charge voltage, cycle delay time, and waveform data recording.
Figure 7.1.1: Channel Settings Interface
  • Mode: Use the [◀] and [▶] buttons to switch between Loop (Cycle Mode), CHG (Charge Mode), and DIS (Discharge Mode).
  • Current Gear: Use the [◀] and [▶] buttons to switch the current gear between High Current and Low Current.
  • Cycle Count: Use the [◀] and [▶] buttons to set the number of cycles, ranging from 1 to 9.
  • Charge Cut-off Current: Use the [◀] and [▶] buttons to set the charge cut-off current. For example, if set to 0.050A, the device will stop charging when the current is below 0.050A.
  • Discharge Cut-off Voltage: Use the [◀] and [▶] buttons to set the discharge cut-off voltage. For example, if set to 2.500V, the device will stop discharging when the battery voltage is below 2.500V.
  • End Charge Voltage: Use the [◀] and [▶] buttons to set the end charge voltage. For example, if set to 3.450V, the device will stop charging when the battery voltage exceeds 3.450V.
  • Cycle Switching Time: Use the [◀] and [▶] buttons to set the cycle switching time. For example, if set to 10S, the battery will switch to discharge mode after charging ends for 10 seconds.
  • Data Recording: Use the [◀] and [▶] buttons to enable or disable the data recording function. When enabled, data will be automatically recorded.

7.2 Basic Settings Interface

Screenshot of the system settings interface, showing options for language, sound, screen brightness, auto-off, channel synchronization, charge/discharge balance, about, and factory reset.
Figure 7.2.1: System Settings Interface
  • Language: Use the [◀] and [▶] buttons to switch between Chinese and English.
  • Sound: Use the [◀] and [▶] buttons to enable or disable sound prompts.
  • Brightness: Use the [◀] and [▶] buttons to adjust the screen brightness to an appropriate level.
  • Auto-off: Use the [◀] and [▶] buttons to set the screen off time. Selecting "OFF" will keep the screen always on.
  • Channel Sync: Use the [◀] and [▶] buttons to enable channel synchronization. When enabled, parameters for channels 2, 3, and 4 will be synchronized with channel 1.
  • Charge/Discharge Balance: Use the [◀] and [▶] buttons to enable the charge/discharge balance function. When enabled, the device will intelligently utilize battery energy. For example, if all four channels are in cycle mode, and a battery is inserted into channel 1 for charging, and then a battery is inserted into channel 2 and cycle mode is enabled, the device will automatically prioritize discharging the channel 2 battery, and the discharged energy will be recycled to charge the channel 1 battery.
  • About: Short press the [OK] button to view the device model, serial number, and version information.
  • Factory Reset: Short press the [OK] button to bring up the factory reset prompt window. Press [OK] again to restore the device to factory settings.

8. Mobile App Control

8.1 Android App Usage Instructions

8.1.1 App Download

Download the app from the following server link: http://68.168.132.244/JunceHome/JunceHome.apk

8.1.2 App Installation and Device Connection

This software only supports Android 9.0 and above. To use the software, you need to allow "Junce Home" to access location information and permission to find and connect to nearby devices. (Due to Android system restrictions, please enable your phone's GPS location first to search for and connect to Bluetooth models in the app. Note: This app does not have location functionality itself).

Screenshots illustrating the Android app installation process, including scanning a QR code or entering a download link, downloading the APK file, and installing the app.
Figure 8.1.2.1: Android App Installation Steps

8.1.3 App Interface Display

After clicking the app icon, the app will automatically detect if there is a new version in the background, and a pop-up window will remind you to update to the new version.

Screenshots of the Android app's list interface, single-channel interface, curve interface, and cycle results interface.
Figure 8.1.3.1: Android App Interface Views

8.2 iOS App Usage Instructions

8.2.1 App Download

Search for "Junce Home" in the Apple App Store to download.

8.2.2 App Installation and Device Connection

The software only supports iOS 9.0 and above. The first time the software connects to Bluetooth, it will ask for Bluetooth access; please agree. The device connection method is the same as for Android.

8.2.3 Software Update

You can get the latest software from the Apple App Store. Different versions may vary slightly, so it is recommended to update to the latest version for the best user experience.

9. PC Software Control

9.1 Software Download and Installation

Communication Protocol and Software Link: http://68.168.132.244/bts04/bts04.exe

Copy the link to your browser to download. Double-click the [bts04.exe] application to run it, and follow the steps to install.

9.2 Connection

After connecting the device to the computer via a Type-C USB data cable, you can select the device from the dropdown list in the software and click connect. Once the serial number and instrument model are displayed, it indicates a successful connection, and the light in the upper right corner will turn green from red.

9.3 List Interface

You can view various parameters for all four channels and select different operating modes, as well as enable/disable battery charging and discharging.

9.4 Large Screen Interface

You can choose a channel to view all parameters on a large screen, which is more intuitive.

9.5 Curve Interface

You can view charge V-mAh curves, discharge V-mAh curves, charge V-Wh curves, and discharge V-Wh curves.

9.6 Test Summary Interface

You can view the test results for the channel.

9.7 Settings Interface

You can set channel parameters and system settings.

10. Troubleshooting

The following lists possible issues and troubleshooting methods for the BTS04 series during use. If you encounter these issues, please follow the corresponding steps to resolve them. If you cannot resolve them, please contact JUNCTEK Hangzhou Junce Instrument Co., Ltd. and provide your device information.

Q1: How to download and install the mobile APP?

Mobile APP Installation and Device Pairing Guide:

  1. Scan QR Code: First, use your phone to scan the QR code in the quick start guide to download and successfully install the corresponding mobile APP.
  2. Enable Bluetooth: Turn on Bluetooth in your phone's settings to facilitate Bluetooth connection with the instrument.
  3. Enable Location Services: To meet Android system connection requirements, please also enable your phone's location services. We solemnly promise not to collect or use any of your location information.
  4. Search and Connect to Device: Launch the mobile APP, click the search function, and select the KMFXXXXXX device from the search results. After selecting the device, the APP will read and display its measurement information.

Q2: Why is the file downloaded by my phone scanning the QR code on the machine a compressed package instead of an APK file, preventing APP installation?

  1. On some Android phones, downloaded applications may automatically be identified as compressed files. If you encounter this, you only need to make a simple manual change:
  2. Find the downloaded file, usually with a .ZIP extension, such as "JunceHome.APK.ZIP". Then, remove the .ZIP extension from the file name, i.e., rename it to "JunceHome.APK". After completing these steps, you can install the application normally.

Q3: After installing the APP and turning on Bluetooth, the APP cannot find the device.

  1. The problem you are experiencing is due to location permissions not being enabled on your Android phone, which prevents the APP from finding the device. Once you enable location services, you can use the APP's search function to connect to the Bluetooth device.

Q4: Why does the device suddenly stop charging/discharging the battery?

  1. High device temperature may be the culprit. When the device temperature exceeds 75℃, the system will automatically stop charging/discharging to protect the device and battery safety. You can check system prompt messages in the system settings interface. If it is confirmed that the temperature is too high, let the device cool down quietly and continue use after the temperature drops to a safe range.

Q5: The screen displays "BATTERY REVERSED", how to handle this?

  1. The "BATTERY REVERSED" prompt indicates that the battery in the current channel is reversed. You need to remove the battery from the device, reinsert it according to the correct positive and negative directions, and ensure the battery is connected correctly. The device should then resume normal operation.

Q6: When in cycle mode and data recording is enabled, why is there no data record on the curve interface?

  1. In cycle mode, data recording follows specific rules, only recording data for the last cycle. For example, if the cycle count is set to 9, the device will only record data for the 9th charge and discharge, so the curve interface will not display data for other cycles.

Q7: All four channels are in cycle mode, why do channels 1 and 2 alternate charge/discharge status?

  1. This is because the charge and discharge balance function is enabled in the system settings. When this function is enabled, the device intelligently utilizes battery energy. Taking four channels in cycle mode as an example, when a battery is inserted into channel 1 and starts charging, and then a battery is inserted into channel 2 and cycle mode is enabled, the device will automatically prioritize discharging the channel 2 battery, and the energy generated by discharging the channel 2 battery will be recycled to charge the channel 1 battery, thereby achieving efficient energy utilization and cycle balance.

Q8: After the instrument is powered on, the default display is the list interface. Can it be changed to the single-channel interface, results interface, or curve interface?

  1. In the list interface, single-channel interface, results interface, or curve interface, select any interface and long press the [SET] button. After the screen displays "Saved", the instrument will default to the interface you saved the next time it is powered on.

Q9: When the instrument enters repair mode, how to exit this mode?

  1. When the channel is in repair mode, short press the [OK] button to exit.

11. User Tips

  • For accurate internal resistance measurements, ensure good contact between the battery terminals and the tester's slots.
  • When using the mobile app or PC software, ensure your device's Bluetooth is enabled and location permissions are granted for successful connection.
  • If you experience high temperatures during testing, allow the device to cool down to prevent automatic shutdown and ensure longevity.
  • Always double-check battery polarity before insertion to avoid 'BATTERY REVERSED' errors and potential damage.

12. Warranty and Support

This product is covered by a manufacturer's warranty against defects in materials and workmanship. For warranty claims, technical support, or service inquiries, please contact your original point of purchase or refer to the official JUNCTEK website for contact information. Please have your product model and serial number ready when contacting support.

A detailed user manual in PDF format is available for download: User Manual (PDF)

© 2025 Voktta. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.