manhot MH82-TYZ1

Contents

MANHOT 5th Generation Smart Zigbee Electric Curtain Motor User Manual

Model: MH82-TYZ1

1. Introduction

This intelligent curtain motor is a battery-powered electric curtain motor that enables the smart control of ordinary curtains. It features a built-in wireless communication module that connects to your network for remote control, timing functions, voice control for opening and closing curtains, and intelligent linking with multiple devices.

For detailed instructions and diagrams, please refer to the full PDF user manual available at: MANHOT Zigbee Curtain Motor User Manual (PDF)

2. Package Contents

Please check the box for the following items:

  • 1 x Electric Curtain Motor
  • 1 x Curtain Motor Battery (5800mAh)
  • 1 x Remote Control
  • 1 x USB Cable (for charging)
  • 1 x User Manual
MANHOT Smart Curtain Motor components: motor, remote control, and USB cable.

Figure 2.1: Package Contents

3. Setup

3.1 Battery Installation and Removal

The motor features a removable battery for convenient charging.

Battery Installation:

  1. Take out the motor assembly and battery assembly separately. Ensure that the interfaces of both are clean and free of foreign objects, and make sure the mounting surfaces are flat.
  2. Align the mounting interfaces of the motor and battery completely (motor to the left, battery to the right), and push them smoothly towards the center in a horizontal direction until you hear or feel the latch engage.
  3. Check that the motor and battery are tightly fitted with no looseness. Confirm that the installation is complete.

Battery Removal:

  1. When the motor is low on battery, simply remove the battery section. There is no need to disassemble the entire motor.
  2. The battery has a built-in Type-C charging port. After fully charging, just install the battery back onto the motor.
Steps for installing the removable battery into the motor.

Figure 3.1: Removable Battery Installation

Steps for removing the battery and charging it via Type-C port.

Figure 3.2: Battery Removal and Charging

3.2 Motor Installation and Disassembly

Installation:

  1. Check if the pull-out lock rod is in the position shown in the diagram (left side). If it is on the right side, first pull the pull-out lock rod while pulling it to the left side.
  2. Align the motor shaft with the hole position and insert it into the main transmission box.
  3. Pull the locking rod to the right until the rod head falls into the right limit hole, and complete the installation.

Disassembly:

  1. Pull the locking rod downwards to slide its top out of the limit hole.
  2. Pull the locking rod to the left side.
  3. Directly remove the motor.

Attention:

  • Ensure that the locking rod is in the position shown in the diagram.
  • The ceiling for installing the motor must be sturdy enough to withstand all the weight, including the track, motor, and curtain cloth.

3.3 Zigbee Gateway and Tuya App Setup

This product is controlled by the TUYA System. Please download the TUYA APP and add the Zigbee gateway before using it.

  1. Scan the QR code on the right side (or search 'Tuya Smart' in your app store), download and install the Tuya app. Open the app to register and log in to your account.
  2. After short pressing the motor setting button three times in a row, press and hold it for another two seconds until the indicator light continues to flash rapidly.
  3. Open the app, enter 'Smart Gateway' and click 'Add Sub Device'.
  4. Wait for the search device on the search interface, and then click 'Finish Add'.
Diagram showing the connection of Zigbee Smart Blinds Motor with WiFi router, Zigbee Gateway, and APP Control.

Figure 3.3: Zigbee Smart Blinds Motor Connection Diagram

4. Operating Instructions

4.1 Remote Control Pairing

  1. Press and hold the motor setting button for 2 seconds until the indicator light remains on.
  2. Press the open button on the remote control, and the indicator light will flash once.
  3. Press the P2 button on the back of the remote control again, and the indicator light will turn off to complete pairing.

Note: To clear remote pairing, please reset to factory settings.

4.2 Motor Direction Reverse

If the motor direction is opposite to the actual curtain movement, you can reverse it.

Method 1: Setting Button Reversing

Short press the settings button, then long press for 2 seconds until the indicator light flashes and the motor shakes.

Method 2: Remote Control Reversing

  1. Press the P2 button on the remote control, and the motor indicator light will flash once.
  2. Press the P2 button on the remote control again, and the motor indicator light will remain on.
  3. Press the stop button on the remote control once, the indicator light will turn off, and the motor will shake at the same time.

4.3 Motor Speed Settings

There are three options for motor speed, with the default being the middle gear. Lowering the speed can reduce the noise during motor operation.

  1. Press the P2 button on the remote control, and the motor indicator light will flash once.
  2. Press the P2 button on the remote control again, and the motor indicator light will remain on.
  3. Press the open and stop buttons on the remote control at the same time, and the indicator light will turn off. At the same time, the motor will shake, and the speed will increase.

Repeat steps 1 and 2, and press both the close and stop buttons on the remote control at the same time, and the speed will decrease.

4.4 Travel Settings (Stroke Calibration)

The first time the motor is powered on, it needs to undergo stroke calibration. Open and close the curtains once, and complete the stroke calibration by hitting both ends of the track.

After stroke calibration, if there is any abnormal blockage, the motor will automatically clear the stroke. In general, when the motor is powered off and then on again, it needs to perform stroke calibration again. If you need to save the stroke after power off, please make the following settings:

Method 1: Setting Button Set

Short press the settings button twice, then long press for 2 seconds until the indicator light flashes and the motor shakes slightly.

Method 2: Remote Control Set

  1. Press the P2 button on the remote control, and the motor indicator light will flash once.
  2. Press the P2 button on the remote control again, and the motor indicator light will remain on.
  3. Press the close button on the remote control, the indicator light will turn off and the motor will shake at the same time.

4.5 Open Position Settings

If you don't want the curtains to open to the very end, you can set a preferred open position.

  1. Use the remote control to move the curtain to the desired opening position.
  2. Press the P2 button on the remote control, and the motor indicator light will flash once.
  3. Press the P2 button on the remote control again, and the motor indicator light will remain on.
  4. Press the open button on the remote control, the indicator light will turn off, and the motor will shake at the same time.

Note: Repeat this operation to cancel the setting. After setting, pressing the remote control open button, manually pulling the curtain open, or using the APP open button will open to the specified position only.

4.6 Hand Pull Run Settings

You can gently pull the curtain a certain distance, and the motor will automatically run to the open/close position.

To enable or disable this function, please make the following settings:

  1. Press the P2 button on the remote control, and the motor indicator light will flash once.
  2. Press the P2 button on the remote control again, and the motor indicator light will remain on.
  3. Press the open and close buttons on the remote control at the same time; the indicator light will turn off, and the motor will shake slightly.

4.7 APP Remote Control

Control your curtains via the Tuya APP/Smart Life APP. You can download it from your app store.

Image showing a smartphone with the Tuya app controlling the curtain motor.

Figure 4.1: APP Remote Control

4.8 Voice Control

Simply give a voice command to Alexa, Google Home, Yandex Alice, or SmartThings to turn on/off curtains when your hands are full.

A woman reading a book with various smart speakers (Alexa, Google Home) in the foreground, demonstrating voice control.

Figure 4.2: Voice Control Integration

4.9 Manual Control

You can open/close the curtain manually even if there is no power supply, thanks to the integrated electromagnetic clutch.

A person manually opening curtains, demonstrating manual control even without power.

Figure 4.3: Manual Control

4.10 Gently Pull Start On/Off

When there is power, push the curtain a little, and it will automatically open or close.

Image showing the 'Gently Pull Start' feature, where a slight tug on the curtain activates the motor.

Figure 4.4: Gently Pull Start

4.11 Schedule Control

You can close the curtains when you sleep or customize your own intelligent plan using the app.

Image showing a smartphone screen with schedule settings for curtains, allowing users to customize opening and closing times.

Figure 4.5: Schedule Control

5. Maintenance

5.1 Battery Charging

When the motor battery is low, remove the battery section and charge it using the provided USB Type-C cable. Ensure the battery is fully charged before re-installing it into the motor.

5.2 Cleaning

Wipe the motor and remote control with a soft, dry cloth. Do not use abrasive cleaners or solvents, as they may damage the surface.

6. Troubleshooting

6.1 Restore Factory Settings

Restoring factory settings will clear all settings, including remote control pairing and travel settings.

  1. Press and hold the motor setting button for 2 seconds until the indicator light is constantly on.
  2. Press the motor setting button for another 5 seconds until the indicator light flashes, which means the factory settings have been restored.

6.2 Common Issues

  • Motor Not Responding: Check if the battery is charged and properly installed. Ensure the remote control is paired.
  • App Connectivity Issues: Verify your Zigbee gateway is online and properly connected to the Tuya app. Ensure the motor is within range of the gateway.
  • Curtain Stops Mid-Way: The motor features obstacle detection. Check for any obstructions in the curtain track. Re-calibrate travel settings if necessary.

7. Specifications

Table showing product dimensions and specifications for the Zigbee Smart Curtain Motor.

Figure 7.1: Product Dimensions and Specifications

ParameterValue
ModelMH82-TYZ1
Rated Power20W
Rated Torque1.2Nm
Rated Speed60r/min
Running Noise< 33dB
Wireless ProtocolZigbee IEEE 802.15.4
Remote Control Frequency2.4G/BT (433.92Mhz for remote)
Battery Capacity5800mAh
Charging PortType-C (DC 5V/2A)
Max Load Capacity40KG
Level of ProtectionIP40
Operation Temperature-10°C to 50°C
Motor Dimensions188mm x 50mm x 60mm
CertificationsCE, RoHS

8. User Tips

  • Optimize Battery Life: To maximize battery life, consider setting schedules for curtain operation rather than frequent manual adjustments.
  • Smart Home Integration: For the best experience, integrate your curtain motor with your preferred smart home ecosystem (Alexa, Google Home, SmartThings) to leverage voice control and advanced automation routines.
  • Initial Calibration: Always perform the stroke calibration (travel settings) accurately during the initial setup to ensure smooth and precise curtain movement.

9. Warranty and Support

For warranty information and technical support, please contact your retailer or the manufacturer directly. Keep your proof of purchase for any warranty claims.

© 2024 MANHOT. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.