SHAOQI TO105

Contents

SHAOQI TO105 Motorcycle Oil Filter User Manual

Model: TO105 | Brand: SHAOQI

SHAOQI TO105 Motorcycle Oil Filter with Benelli motorcycles in background

Image: SHAOQI TO105 Motorcycle Oil Filter for Benelli models.

1. Product Overview

This manual provides essential information for the proper installation, operation, and maintenance of your SHAOQI TO105 Motorcycle Oil Filter. This product is designed as a direct replacement accessory for compatible Benelli motorcycle models.

Product Showcase

Video: A rotating view of the SHAOQI TO105 Motorcycle Oil Filter, showcasing its design and features.

2. Setup and Installation

Proper installation is crucial for the performance and longevity of your motorcycle's engine. Always ensure the engine is cool before beginning any work.

Safety Information & Warnings:

  • Install under the guidance of professional maintenance personnel.
  • Do not modify or force installation.
  • Test safely before normal use.
  • Ensure the correct oil filter is used for your specific motorcycle model.

Installation Steps:

  1. Locate the existing oil filter on your motorcycle.
  2. Place a drain pan beneath the oil filter and engine to catch any oil spillage.
  3. Carefully remove the old oil filter, ensuring all old gasket material is removed from the engine mounting surface.
  4. Apply a thin film of clean engine oil to the gasket of the new SHAOQI TO105 oil filter. This helps create a proper seal.
  5. Thread the new oil filter onto the engine by hand until the gasket makes contact with the engine mounting surface.
  6. Using an appropriate oil filter wrench, tighten the filter to the specified torque.

Tightening Specification: Oil the gasket and tighten the filter with wrench to 15 Nm.

SHAOQI TO105 Oil Filter with 15 Nm torque specification

Image: Side view of the oil filter showing the part number (260146090010) and the critical tightening torque of 15 Nm.

Bottom view of SHAOQI TO105 Oil Filter showing gasket and threaded opening

Image: Bottom view of the oil filter, highlighting the gasket and threaded opening for proper sealing and fitment.

  1. Refill the engine with the recommended type and amount of engine oil according to your motorcycle manufacturer's specifications.
  2. Start the engine and check for any oil leaks around the new filter. If leaks are present, turn off the engine and re-tighten slightly, or re-evaluate the installation.
  3. Turn off the engine and check the oil level again, topping up if necessary.

3. Operating

Once installed correctly, the oil filter operates continuously to remove contaminants from your engine oil. No specific user interaction is required during operation.

Post-Installation Check:

  • Regularly check your engine oil level and condition as per your motorcycle's owner manual.
  • Monitor for any unusual engine noises or warning lights that might indicate an issue with oil pressure or filtration.

4. Maintenance

The oil filter is a consumable part and requires periodic replacement. It is not designed to be cleaned or reused.

  • Replace the oil filter according to your motorcycle manufacturer's recommended service intervals, typically during every oil change or as specified in your owner's manual.
  • Always use a new gasket when installing a new oil filter.

5. Troubleshooting

If you encounter issues after installing the oil filter, consider the following:

Oil Leaks:

  • Cause: Improper tightening, damaged gasket, or debris on the mounting surface.
  • Solution: Turn off the engine, allow it to cool, and inspect the filter. Ensure the old gasket is fully removed. Re-tighten the filter to the specified torque (15 Nm). If the gasket is damaged, replace the filter.

Low Oil Pressure Warning:

  • Cause: Incorrect filter, severely clogged filter (unlikely with a new filter), or other engine issues.
  • Solution: Immediately stop the engine. Check oil level. Verify the correct filter model was installed. If the issue persists, consult a professional mechanic.

6. Specifications

Product NameMotorcycle Oil Filter
BrandSHAOQI
ModelTO105
Part Number260146090010
MaterialAluminum Alloy
ColorBlack
Item TypeOil Filters
OriginMainland China
Tightening Torque15 Nm
CompatibilityFor Benelli 502C, TRK502, TRK502X, BJ500, BJ600, Leoncino500, Leoncino 500, TNT600, TNT300, BN600, 600BN. (Always verify fitment with your motorcycle's specifications.)
DimensionsSpecific dimensions (diameter, height, hole diameter) are not provided in the product information. Please refer to your motorcycle's specifications for compatible filter sizes.

7. User Tips

  • Verify Compatibility: Before purchasing and installing, always double-check your motorcycle's model, year, and existing filter dimensions to ensure a perfect fit. This is crucial as specific measurements are not universally provided.
  • Gasket Lubrication: Always lubricate the new filter's gasket with fresh engine oil before installation to ensure a proper seal and prevent damage.
  • Torque Wrench Use: Using a torque wrench to tighten the filter to 15 Nm is highly recommended to prevent over-tightening (which can damage the filter or engine) or under-tightening (which can cause leaks).

8. Warranty and Support

This product is a replacement accessory and is not an original equipment manufacturer (OEM) part. Normal wear and tear are not covered under warranty.

For further assistance or technical support, please refer to the seller or your motorcycle's authorized service center.

© 2024 SHAOQI. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.