MOES BS-FB-V3

Contents

MOES Smart ZigBee Fingerbot Button Pusher User Manual

Model: BS-FB-V3

1. Product Introduction

The MOES Smart ZigBee Fingerbot Button Pusher is the world's smallest robot designed to smartly control various types of buttons and switches. It transforms your existing home appliances into smart devices through robotic clicks, allowing for app control, voice commands, and scheduled operations. This device offers a flexible and non-invasive way to automate your home.

MOES Smart ZigBee Fingerbot Plus with various tool arms and logos for Siri, Alexa, Google Assistant.
The MOES Smart ZigBee Fingerbot Plus, showcasing its compact design and compatibility with popular voice assistants.

2. Product Specifications

FeatureSpecification
ModelBS-FB-V3
Dimensions34.5 x 34.5 x 34.5 mm
Weight38g
Communication ProtocolZigBee 3.0 (BLE 4.2 also mentioned in manual)
FunctionalitiesApp Control, Voice Control, Cloud Control, Scheduler
Stall Torque2.0 kgf·cm
Maximum Arm Movement12 mm
Working Temperature-10°C ~ 55°C (14°F ~ 131°F)
Battery TypeCR2
Battery Capacity500 mAh
Frequency Band2.4GHz
Maximum Radio Transmit Power+4dbm

3. Safety Warnings and Precautions

CAUTION! Before beginning the installation, please read carefully and entirely this guide and any other documents accompanying the device.

  • Do not disassemble, reassemble, modify, or attempt to repair this product by yourself. This work should be performed by authorized professionals.
  • The product is non-waterproof. Do not install it on or near underwater appliances.
  • The product contains a lithium battery; therefore, it is prohibited in humid, high-temperature environments.
  • Do not hinder the movement of the Fingerbot's arm when it is working. Otherwise, it may cause the arm to fall off and damage to the motor inside the Fingerbot.

Battery Safety Warnings:

⚠ WARNING: INGESTION HAZARD

  • This product contains a button cell or coin battery.
  • DEATH or serious injury can occur if ingested.
  • A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.
  • KEEP new and used batteries OUT OF REACH of CHILDREN.
  • Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.

Additional Battery Precautions:

  • Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children.
  • Do NOT dispose of batteries in household trash or incinerate.
  • Even used batteries may cause severe injury or death. Call a local poison control center for treatment information.
  • Non-rechargeable batteries are not to be recharged.
  • Do not force discharge, recharge, disassemble, heat above 60°C, or incinerate. Doing so may result in injury due to venting, leakage, or explosion resulting in chemical burns.
  • Ensure that the battery is correctly loaded into the battery compartment according to the polarity marked, and the positive and negative poles cannot be installed reversely.
  • Do not mix old and new batteries, different brands, or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.
  • Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.
  • Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

4. Setup and Installation

4.1. Unboxing and Initial Power-Up

Upon receiving your Fingerbot, carefully unbox the device. The package typically includes the Fingerbot unit. Tool packs with various arms are sold separately.

Video demonstrating the unboxing, battery installation, and initial setup of the MOES ZigBee Fingerbot.
  1. Open the back cover of the Fingerbot.
  2. Remove the insulation paper from the battery compartment.
  3. Long press the reset button (located near the battery) until the indicator light flashes, indicating it's ready for pairing.

4.2. App Installation and Device Pairing

The Fingerbot is controlled via the MOES App. A ZigBee gateway is required for wireless remote control and voice control functionalities.

  1. Download the MOES App from the App Store (for iOS) or Google Play (for Android). You can scan the QR code below to quickly find the app.
    2. QR code for MOES App download
    Scan this QR code to download the MOES App.
  2. Register or Log in to your MOES account. If you don't have an account, tap "Register" and follow the prompts.
  3. Ensure your phone's Bluetooth is turned on.
  4. In the MOES App, navigate to your ZigBee gateway.
  5. Confirm the Fingerbot's blue light is flashing. If not, long press the reset/function button until a prompt tone is heard and the blue light starts slow flashing, indicating it's in distribution network state.
  6. In the MOES App, click "+" or "Add Device". The app should automatically discover the Fingerbot.
  7. Once discovered, click "Add" and then "Done" to complete the pairing process.

4.3. Physical Installation of Fingerbot

The Fingerbot can be attached to various buttons and switches using double-sided tape. Ensure the surface is clean before installation.

Fingerbot Plus installed on a PC power button, a light switch, and a MAXHUB screen button.
The Fingerbot Plus can be stuck anywhere to remotely control devices like PC power buttons, light switches, or interactive screen buttons.
  1. Clean the surface of the button or switch panel where you want to install the Fingerbot.
  2. Attach the Fingerbot to the panel using the provided double-sided tape.
  3. Connect your Fingerbot with the App and calibrate the movement of the Fingerbot's robotic arm to fit your switches and buttons.
  4. After installation, it is recommended to let the Fingerbot rest for 24 hours to reach maximum adhesion.

4.3.1. Installing the Straight Arm (for Push Buttons)

The straight arm is ideal for pushing standard buttons. Three different lengths are available (sold separately in tool packs) to suit various button types.

Diagram showing the Fingerbot Plus with various straight tool arms and their dimensions.
Diagram illustrating the Fingerbot Plus and the dimensions of various straight tool arms. Note: Tool packs are sold separately.

Install the straight arm by sliding it into the slot on the Fingerbot's robotic arm until it clicks into place.

4.3.2. Installing the Rocker Arm (for Rocker Switches)

The rocker arm is designed to push and pull rocker switches. This allows the Fingerbot to change the switch status of equipment.

Fingerbot Plus installed on a light switch with a rocker arm, showing manual touch control.
The Fingerbot Plus installed on a light switch, demonstrating its ability to be triggered manually via its touch panel.
  1. After connecting Fingerbot with the App, set Fingerbot to the 'Switch' mode.
  2. Move the arm of Fingerbot to the bottom and fix the Fingerbot on the switch panel.
  3. Tear off the tape covering on the rocker arm to stick the arm to the switch button.
  4. After ensuring the firmness, use the App to adjust the rising range of Fingerbot's arm, so that its movement range can be adapted to the switch button.
  5. If the app is showing the opposite status to the actual status, please use the 'invert' function in the app to invert the display mode.

4.3.3. Installing the Ring Arm (for Toggle Switches)

The ring arm is used to push and pull toggle switches, changing the equipment's status.

Fingerbot Plus with various attachments for buttons, rocker switches, and toggle switches.
The Fingerbot Plus is versatile, suitable for buttons, rocker switches, and toggle switches with appropriate attachments.
  1. After connecting Fingerbot with the App, set Fingerbot to the 'Switch' mode.
  2. Fix two cushion blocks to the Fingerbot with tape, as shown in the manual.
  3. Put the ring of the arm on the toggle button, and tear off the tape covering on the other side of the cushion block to fix the Fingerbot on the switch panel.
  4. After ensuring the firmness, use the App to adjust the movement range of the Fingerbot's arm, so that its movement range can be adapted to the toggle.

5. Operating Instructions

5.1. App Control

You can control the Fingerbot directly via Bluetooth with the MOES App when within range of the Fingerbot or its ZigBee gateway.

Fingerbot Plus on a coffee maker, controlled by the Tuya Smart App on a smartphone.
Control your coffee maker and other appliances remotely using the Tuya Smart App with the Fingerbot Plus.
  • Open the MOES App and select your Fingerbot device.
  • Tap the ON/OFF button in the app to activate the Fingerbot.
  • Adjust the "Down Movement" and "Up Movement" settings (0-100) to fine-tune the arm's travel distance for precise control.
  • Use the "Sustain Time" setting to define how long the button is pressed or held.
Smartphone screen showing the 'Sustain Time' setting in the Fingerbot app, controlling a coffee machine.
The "Sustain Time" feature in the app allows for flexible and accurate control, such as holding down a coffee machine button for a specific duration.

5.2. Manual Touch Control (Fingerbot Plus only)

The Fingerbot Plus features a touch button on the device itself, allowing you to manually trigger the robotic arm without needing your phone.

Fingerbot Plus on a light switch, with a finger pressing its integrated touch button.
The Fingerbot Plus allows manual triggering of switches or buttons directly from its integrated touch panel.

Simply press the button on the Fingerbot Plus to activate its function. This provides a convenient alternative to app control.

To prevent accidental operations, especially by children, you can disable the touch control feature within the Smart Life App.

Smartphone screen showing the 'Touch Control' option disabled in the Smart Life App, with a baby near a fan.
Disable the 'Touch Control' feature in the Smart Life App to prevent unintended activation, particularly by children.

5.3. Voice Control

With a ZigBee gateway, the Fingerbot can be integrated with voice assistants like Amazon Alexa and Google Home for hands-free control.

Fingerbot Plus on a robot vacuum, with a Google Home speaker nearby, demonstrating voice control.
Use simple voice commands with Alexa or Google Home to trigger your household appliances connected to the Fingerbot Plus.

Refer to the MOES website for a detailed step-by-step guide on setting up voice control: https://www.moestech.com/blogs/news/smart-device-linked-voice-speaker

5.4. Scheduling and Automation

Set schedules in the MOES App to automatically turn devices ON/OFF at preset times. A ZigBee hub is essential for this feature.

Smartphone screen showing a schedule being set in the Fingerbot app for automatic ON/OFF of a traditional curtain switch.
Timer your schedule for automatic ON/OFF. Note: A ZigBee hub is required for timing schedules.

You can also create groups in the App to manage multiple Fingerbot Plus devices and share control with family members.

Diagram showing multiple Fingerbot devices controlled by one person, and one Fingerbot controlled by multiple people via app groups.
Manage multiple Fingerbot Plus devices in your home by creating groups in the app and sharing access with family members.

6. Maintenance

The Fingerbot is designed for low maintenance. The primary maintenance task involves battery replacement.

6.1. Battery Replacement

When the battery level is low, replace the CR2 battery following the safety warnings in Section 3. Ensure correct polarity during installation.

6.2. Cleaning

Wipe the device with a dry, soft cloth. Do not use liquid cleaners or immerse the device in water.

7. Troubleshooting

  • Device not pairing: Ensure the Fingerbot's blue indicator light is flashing. If not, long press the reset/function button for 5 seconds until it flashes. Check that your phone's Bluetooth is enabled and the ZigBee gateway is properly connected and online in the MOES App.
  • Fingerbot not responding: Check the battery level in the app. Replace the CR2 battery if low. Ensure the Fingerbot is within range of the ZigBee gateway.
  • Arm movement issues: Calibrate the arm movement in the MOES App (0-100 adjustable range). If using a rocker or ring arm, ensure it is securely attached and the 'invert' function is correctly set if needed.
  • Voice control not working: Verify that the ZigBee gateway is connected and the Fingerbot is linked to your voice assistant (Alexa, Google Home). Check your internet connection.
  • Scheduling not working: Ensure a ZigBee hub is connected and properly configured for timing schedules. Check the schedule settings in the MOES App.

For more detailed troubleshooting, please review the product data sheet available at: https://www.moestech.com/blogs/news/bs-fb-v3

8. User Tips

  • For optimal adhesion, allow the Fingerbot to rest for 24 hours after initial installation before heavy use.
  • Experiment with the "Down Movement" and "Sustain Time" settings in the app to achieve the perfect press for different buttons and switches.
  • Utilize the grouping feature in the MOES App to manage multiple Fingerbots efficiently and share control with family members.
  • If you find the manual touch control too sensitive or prone to accidental presses, especially with children around, remember to disable it in the app.

9. Warranty and Support

9.1. Warranty Information

Products are covered by a 24-month warranty, effective from the date of purchase by a retail customer. To exercise warranty rights, the purchaser must present a Warranty card and proof of purchase (e.g., VAT invoice, financial receipt, or other document confirming the actual date of purchase).

The warranty does not cover:

  • Mechanical damage caused by user fault or product defects resulting from such damage.
  • Damage caused by improper use of the product.
  • Natural wear and tear during use.

The warranty will be void under the following circumstances:

  • Removal of the warranty seal or serial number from the product.
  • Attempts to eliminate physical defects outside of authorized service.
  • Use of non-original parts and consumables.

For full warranty terms and conditions, please refer to the official user manual PDF: User Manual (PDF).

9.2. Recycling Information

All products marked with the WEEE symbol (Waste Electrical and Electronic Equipment Directive 2012/19/EU) must be disposed of separately from unsorted municipal waste. To protect your health and the environment, this equipment must be disposed of at designated collection points for electrical and electronic equipment. Contact your local authorities for proper disposal and recycling information.

9.3. Declaration of Conformity

WENZHOU NOVA NEW ENERGY CO., LTD declares that the radio equipment type BS-FB-V3 is in compliance with Directives 2014/53/EU, 2014/30/EU, and 2011/65/EU. The full text of the EU declaration of conformity is available at: https://www.moestech.com/blogs/news/bs-fb-v3

9.4. Contact and Support

For further assistance, please refer to the contact information provided in the original user manual or visit the MOES website.

  • Manufacturer: WENZHOU NOVA NEW ENERGY CO.,LTD
  • After Service Email: service@moeshouse.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.