CAOWTAN NH35 Hands

Contents

CAOWTAN Watch Hand Modification Accessories User Manual

For NH35A/NH36/4R/7S Movement

1. Product Overview

These watch hands are designed as modification accessories for watches equipped with Japan NH35A, NH36, 4R, or 7S movements. They feature a green luminous coating for visibility in low-light conditions and are available in various finishes.

Assortment of watch hands in silver, gold, and rose gold with green luminous tips, suitable for NH35A/NH36/4R/7S movements.
Figure 1: CAOWTAN Watch Hands in various finishes.

2. Setup and Installation

Installation of watch hands requires precision and specialized tools. It is highly recommended that this procedure be performed by a qualified watchmaker or an individual with experience in watch modification to prevent damage to the watch movement or the hands themselves.

  • Watch hand press tool
  • Watchmaker's loupe
  • Dust blower
  • Lint-free cloth
  • Movement holder
  • Hand removal tool (if replacing existing hands)

2.2 Installation Steps (General Guide)

  1. Ensure your workspace is clean, dust-free, and well-lit.
  2. Carefully remove the watch case back and crown to access the movement.
  3. If replacing existing hands, use a hand removal tool to gently lift them off the pinions.
  4. Using a dust blower, remove any dust or debris from the dial and movement.
  5. Position the hour hand onto its pinion. Using a watch hand press tool, apply gentle, even pressure to secure it. Ensure it is level and has sufficient clearance from the dial.
  6. Repeat the process for the minute hand, ensuring it is parallel to the hour hand and has proper clearance.
  7. Finally, install the second hand (if applicable), ensuring it is also level and has adequate clearance from the minute hand and crystal.
  8. Verify that all hands move freely and do not touch each other or the dial/crystal.
  9. Reassemble the watch, ensuring the crown is properly seated and the case back is securely closed.
Video 1: Demonstration of watch hand installation.
Watchmaker using a tool to install watch hands onto a movement.
Figure 2: Watchmaker installing watch hands with a specialized tool.

3. Operating Instructions

These watch hands are passive components designed to indicate time. Their primary operational feature is the green luminous coating.

3.1 Luminous Function

The watch hands are coated with a green luminous material. To activate the luminescence, expose the watch to a light source (natural or artificial) for a period. The hands will then glow in the dark, allowing for time readability in low-light conditions. The duration and intensity of the glow depend on the exposure time and intensity of the light source.

Diagram illustrating the green luminous function of the watch hands for night visibility.
Figure 3: Green luminous feature for night visibility.

4. Maintenance

Proper care will ensure the longevity and appearance of your watch hands.

4.1 Cleaning

  • If the watch hands become dirty during installation or use, gently wipe them with a soft, lint-free cloth.
  • Avoid using harsh chemicals, solvents, or abrasive materials, as these can damage the finish or luminous coating.
  • Ensure the hands are completely dry before reassembling the watch or exposing them to moisture.

4.2 Storage

When not installed, store the watch hands in a dry, dust-free environment, preferably in their original packaging or a protective container, to prevent scratches or damage.

5. Troubleshooting

If you encounter issues after installing the watch hands, consider the following common problems and solutions:

5.1 Hands Not Moving

  • Check Seating: Ensure the hands are properly pressed onto their respective pinions. If too loose, they may not engage with the movement. If too tight, they may bind.
  • Check Clearance: Verify that the hands are not touching each other, the dial, or the inside of the watch crystal. Any contact will impede their movement.
  • Movement Functionality: Confirm that the watch movement itself is functioning correctly.

5.2 Luminous Coating Not Glowing

  • Light Exposure: Ensure the watch has been exposed to a sufficient light source to charge the luminous material.
  • Ambient Light: Test the luminescence in complete darkness, as even dim ambient light can make the glow appear faint.

5.3 Hands Falling Off

  • Improper Installation: The hands may not have been pressed firmly enough onto the pinions during installation. Re-installation with proper tools and technique is required.
  • Damaged Pinion/Hand Hole: Inspect the movement's pinions and the hand holes for any damage that might prevent a secure fit.

6. Specifications

Feature Detail
Brand CAOWTAN
Compatibility Japan NH35A, NH36, 4R, 7S movements
Hand Colors Available Silver, Gold, Rose Gold
Luminous Feature Green Luminous
Material Copper
Hand Size (Hour x Minute x Second) 8mm x 12mm x 12.5mm (measured from the center of the watch hand hole to the top of the watch hand)
Package Dimensions (L x W x H) 12 cm x 12 cm x 2 cm
Package Weight 0.018 kg
Diagram highlighting the copper material of the watch hands.
Figure 4: Watch hands are made of sturdy and durable copper material.

7. User Tips

  • Always handle watch hands with non-magnetic tweezers or specialized tools to avoid bending, scratching, or magnetizing them.
  • When pressing hands, ensure the tool is perfectly aligned to prevent damage to the hand's center hole or the movement's pinion.
  • After installation, perform a visual check under magnification to confirm proper alignment and clearance.

8. Warranty and Support

For specific warranty information, return policies, or technical support regarding your CAOWTAN watch hands, please contact the seller directly through the platform where the purchase was made.

Additional guidance and documents, including a user manual in PDF format, may be available. Please refer to the following link for the official user manual:

View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.