OLOPKY 12V 14.6V 18V 24V Lithium 21700 Battery Pack

Contents

OLOPKY Lithium 21700 Battery Pack User Manual

Model: 12V 14.6V 18V 24V Lithium 21700 Battery Pack

1. Introduction & Scope

This Lithium-Ion Battery Pack, featuring high-performance cells and an intelligent Battery Management System (BMS), offers high energy density, long cycle life, and stable safety characteristics. This manual provides detailed technical parameters, usage instructions, safety guidelines, and maintenance requirements. Please read and strictly follow these instructions before use to ensure proper operation and personal safety.

1.1 Applicable Scenarios

  • Electric sprayers, mobile power supplies, power tools, mobile lighting, emergency power supplies (e.g., energy storage systems, new energy vehicles, consumer electronics).
  • Bluetooth speakers, electric toys, LED lighting.

1.2 Operating Environment

  • Operating Temperature: -10℃ to 60℃
  • Humidity: 10% to 90% (non-condensing)
  • Target Users: Professional installers and end-users with basic electrical knowledge.

1.3 Referenced Standards

  • National Standards: GB/T 42729-2023 (Safety Guidelines for Lithium-Ion Batteries and Battery Packs), GB 43854-2024 (Safety Technical Specifications for Lithium-Ion Batteries for Electric Bicycles, if applicable).
  • International Standards: IEC 62133-2:2017, UL 1642, UN38.3.

2. Product Information

2.1 Product Model & Name

  • Model: 12V, 14.6V, 18V, 24V (e.g., 48V100Ah Lithium Iron Phosphate Energy Storage Battery Pack)
  • Nominal Capacities: 5AH, 7AH, 12AH, 15AH, 20AH, 25AH, 30AH

2.2 Product Structure

Component Name Function Description
Battery Cell Energy storage core, typically 21700 Lithium-ion cells.
BMS Protection Board Overcharge, over-discharge, overcurrent, short circuit, over-temperature protection, balancing management.
Shell Flame retardant, waterproof, shock-resistant. Material: ABS (e.g., ABS/Aluminum alloy).
Positive and Negative Terminals Output/input interface, typically M5 connection tabs.
Communication Port (if equipped) Communicates with devices/controllers. Type: (e.g., RS485/CAN).
Display Screen (if equipped) Displays SOC (State of Charge), voltage, temperature, and fault status.

2.3 Dimensions & Weight

The battery pack typically measures 151mm (length) x 99mm (width) x 100mm (height) and weighs approximately 1.2kg.

OLOPKY Lithium Battery Pack Dimensions
Figure 1: Dimensions of the OLOPKY Lithium Battery Pack (Length 151mm, Width 99mm, Height 100mm).
OLOPKY Lithium Battery Pack with Display
Figure 2: OLOPKY Lithium Battery Pack with integrated display showing voltage and capacity.

3. Technical Specifications

3.1 Electrical Parameters

Parameter Name Specification Value Test Condition
Rated Voltage 12V, 14.6V, 18V, 24V (e.g., 48V) 25℃, static for 30 minutes
Rated Capacity 5AH, 6AH, 8AH, 10AH, 12AH, 15AH, 20AH (e.g., 100Ah) 0.2C discharge to cut-off voltage
Charging Voltage 12.6V, 14.8V, 21V, 29.4V Constant current and constant voltage charging
Charging Current Standard: 1A (0.3C), Max: 5A (1C) Ambient temperature 0℃~45℃
Discharge Cut-off Voltage 2.5V (e.g., 40V) 0.5C discharge
Continuous Discharge Current 20A (1C) 25℃
Peak Discharge Current 30A (3C) Duration ≤30 seconds
Internal Resistance ≤200 mΩ Single cell, 25℃
Cycle Life ≥1000 cycles (e.g., 2000 cycles) 0.5C charge/discharge, capacity retention ≥80%
Self-Discharge Rate ≤3%/month (e.g., 3%) 25℃ storage, fully charged state
Operating Temp (Charging) 0℃~45℃ -
Operating Temp (Discharging) -10℃~60℃ -

3.2 Environmental & Mechanical Parameters

Parameter Name Specification Value
Storage Temperature -20℃~50℃ (Recommended: 20%~80% SOC)
Relative Humidity 10%~90% (non-condensing)
IP Rating IP65 (e.g., IP65)
Vibration Resistance 10~50Hz, acceleration 5g, 30 minutes in each direction
Impact Resistance 15g, impact duration 6ms, 3 times in each direction
Flame Retardant Grade ≥V0 (UL94 standard)
Key Features of the Battery Pack
Figure 3: Key features including waterproof design, high-quality raw materials, and M5 terminal discharge.

4. Setup (Installation & Wiring)

4.1 Installation Preparation

  1. Ensure the installation environment meets requirements: dry, ventilated, no flammables, away from heat sources (e.g., direct sunlight, heaters).
  2. Prepare tools: wrench, crimping tool, insulation tape, multimeter.
  3. Inspect product appearance: no damage, leakage, bulging, and no oxidation/rust on terminals.
  4. Disconnect all external power supplies to avoid electric shock during installation.

4.2 Wiring Steps

4.2.1 Positive & Negative Wiring

  1. Use a multimeter to confirm battery polarity (Positive: +, Negative: -) to avoid reverse connection.
  2. Strip the insulation layer of external equipment cables (length: 5~8mm) and ensure conductors are free of oxidation.
  3. Connect the cables to the battery's positive and negative terminals, tighten the fixing bolts (torque: 3 N·m) for good contact.
  4. Wrap the terminals with insulation tape to prevent short circuits.

4.2.2 Communication Port Wiring (if applicable)

Battery Port Device Port Wire Color
CAN-H CAN-H
CAN-L CAN-L
RS485-A RS485-A
RS485-B RS485-B
GND GND

4.3 Post-Installation Check

  1. Reconfirm correct wiring: no looseness, short circuit, or reverse connection.
  2. Measure the battery's open-circuit voltage, which should be within the rated range (e.g., 10V~29.4V).
  3. Turn on the external power supply and check if the device recognizes the battery normally without alarm.

5. Operating Instructions

5.1 Charging Operation

  1. Use a charger recommended by the manufacturer or meeting specifications (Charging Voltage: 12.6V-29.4V, Current: 1A-5A).
  2. First connect the charger to the battery, then plug the charger into the mains. The charging indicator (red/green) lights up to indicate charging starts.
  3. During charging, the battery temperature may rise (≤45℃), which is normal; if the temperature exceeds 50℃ or there is odor/smoke, stop charging immediately and disconnect the power.
  4. After charging is complete, the charger indicator changes color (e.g., red→green). Disconnect the connection after standing for 10 minutes.
  5. Prohibited: Overcharging, reverse charging, using damaged chargers, charging in high/low temperature environments (>45°C).

5.2 Discharging Operation

  1. Ensure the working voltage and current of the discharging device match the battery to avoid overload.
  2. Monitor the battery voltage during discharge: do not lower than the discharge cut-off voltage (2.5V per cell), otherwise the BMS will automatically cut off the output.
  3. The continuous discharge current shall not exceed the rated value (20A), and the peak discharge time ≤30 seconds.
  4. Prohibited: Short circuit, overcurrent discharge, discharging in extreme temperatures (0℃ or >60℃).

5.3 Display Operation (if applicable)

Operation Function
Short press power button Wake up screen, display SOC (remaining capacity), voltage, temperature.
Long press power button (3 seconds) Switch display to show cycle count, fault records.
Double click power button Clear non-fatal fault codes (fault must be resolved first).

6. BMS Function Description

6.1 Protection Functions

Protection Type Trigger Condition Action
Overcharge Protection Single cell voltage ≥4.2V (e.g., 3.65V) Cut off charging circuit, prohibit charging
Overdischarge Protection Single cell voltage ≤2.5V (e.g., 2.5V) Cut off discharging circuit, prohibit discharging
Overcurrent Protection (Charging) Charging current ≥20A (e.g., 30A) Cut off charging circuit, delayed recovery
Overcurrent Protection (Discharging) Discharging current ≥30A (e.g., 100A) Cut off discharging circuit, delayed recovery
Short Circuit Protection Positive and negative short circuit, current ≥10A (e.g., 200A) Immediately cut off circuit, manual reset required
Overtemperature Protection (Charging) Cell temperature ≥60℃ (e.g., 48°C) Cut off charging circuit; automatic recovery when temperature ≤30℃ (e.g., 42℃)
Overtemperature Protection (Discharging) Cell temperature ≥60℃ (e.g., 65°C) Cut off discharging circuit; automatic recovery when temperature ≤40℃ (e.g., 55℃)
Low-temperature Protection Cell temperature ≤-10℃ (e.g., -10°C) Prohibit charging/discharging; automatic recovery when temperature ≥10℃ (e.g., 0℃)

6.2 Balancing Function

  • Activation Condition: Battery is charging, and the voltage difference between single cells ≥ 20mV (e.g., 20mV).
  • Working Mode: Active balancing/passive balancing, automatically adjust single cell voltage to ensure battery pack consistency.
  • Balancing Effect: Voltage difference between single cells ≤ 10mV (e.g., 10mV) after balancing.

6.3 Communication & Monitoring Functions

  • Monitored Parameters: SOC (State of Charge, accuracy ±3%), SOH (State of Health), single cell voltage, total voltage, current, temperature.
  • Communication Protocol: (e.g., CANopen, Modbus-RTU).
  • Data Update Frequency: (e.g., 1Hz).

7. Safety Warnings & Precautions

7.1 Warning Classification

  • DANGER (Fatal Hazard): Violation will result in severe personal injury or death.
  • WARNING (Serious Hazard): Violation may result in personal injury or equipment damage.
  • CAUTION (General Hazard): Violation may result in equipment malfunction or performance degradation.

7.2 Core Safety Warnings

7.2.1 DANGER (Fatal Hazard)

  1. Prohibited to short-circuit the battery's positive and negative terminals (e.g., connecting with metal tools), which may cause fire, explosion, battery leakage, and serious injury.
  2. Prohibited to pierce, squeeze, or impact the battery shell, which may cause thermal runaway, explosion, and endanger life safety.
  3. Prohibited to put the battery into fire or high-temperature environments (>80°C), which will cause explosion and combustion.
  4. Prohibited to disassemble the battery or modify the BMS; internal high voltage and chemicals may cause electric shock, corrosion, and fire.

7.2.2 WARNING (Serious Hazard)

  1. Only use chargers that meet specifications; improper chargers may cause overcharging, fire, and battery damage.
  2. Avoid the battery contacting water or other liquids; if water enters, disconnect the power immediately to prevent short circuit and electric shock.
  3. If the battery shows bulging, leakage, odor, smoke, or abnormal temperature rise, stop using it immediately, keep away from people and contact the manufacturer; do not handle it yourself.
  4. Battery installation and maintenance must be performed by professionals; non-professionals are prohibited from touching high-voltage terminals.

7.2.3 CAUTION (General Hazard)

  1. Avoid storing the battery at full charge or low charge for a long time; recommended storage capacity is 20%~80%.
  2. Prohibited to store the battery with metal objects (e.g., keys, coins) to prevent short circuit.
  3. Handle the battery with care during transportation, avoid dropping it, which may affect battery performance.
  4. Keep children and pets away from the battery to prevent danger from incorrect operation.

8. Troubleshooting

Fault Phenomenon Possible Causes Troubleshooting Methods
Cannot Charge 1. Charger fault; 2. Loose/reversed wiring; 3. Battery over-temperature/low-temperature; 4. Battery already overcharged. 1. Replace with a qualified charger; 2. Check and re-tighten wiring; 3. Wait for temperature to return to normal range; 4. Disconnect power, let stand for 30 minutes, then retry.
Cannot Discharge 1. Discharge device overload; 2. Battery over-discharge protection; 3. Incorrect wiring; 4. BMS fault. 1. Reduce device load; 2. Activate by charging promptly; 3. Check positive and negative wiring; 4. Contact manufacturer for BMS repair.
Significant Capacity Drop 1. Too many cycles; 2. Long-term high-temperature storage; 3. Excessive charge/discharge current; 4. Inconsistent single cells. 1. Normal wear, battery replacement needed; 2. Improve storage environment; 3. Charge/discharge at rated current; 4. Check BMS balancing function.
Abnormal Battery Heating 1. Excessive charge/discharge current; 2. Short circuit risk; 3. Cell fault; 4. Poor heat dissipation. 1. Reduce current; 2. Check wiring for short circuits; 3. Stop use and contact manufacturer; 4. Improve ventilation and heat dissipation.
Display Screen Not Working (if equipped) 1. Battery low power; 2. Display screen fault; 3. Loose wiring. 1. Activate by charging; 2. Contact manufacturer for display replacement; 3. Check display wiring.

9. Maintenance

9.1 Daily Maintenance

  1. Clean the battery shell regularly with a dry soft cloth; do not use wet cloth or chemical solvents.
  2. Inspect the wiring terminals once a month: no looseness, oxidation, or rust; wipe the contacts with alcohol if necessary.
  3. Inspect the battery appearance once every 3 months: no bulging, leakage, or damage.
  4. Perform a full charge-discharge cycle every 6 months to activate cell activity (0.2C charge-discharge).

9.2 Long-term Idle Maintenance

  1. Charge the battery to 50%~60% before idling.
  2. Storage environment: dry, ventilated, cool (temperature 10℃~25℃), away from flammables and heat sources.
  3. Supplementary charging once every 3 months to maintain capacity at 40%~70% to prevent overdischarge.
  4. Prohibited to idle in full charge or low charge state for a long time.

9.3 Maintenance Taboos

  1. Prohibited to rinse the battery with water or soak it in liquid.
  2. Prohibited to tap the battery terminals with metal tools.
  3. Prohibited to disassemble the battery or replace cells by yourself.
  4. Prohibited to perform maintenance operations while the battery is powered on.

10. User Tips

  • Always use the recommended charger to avoid damage and ensure battery longevity.
  • For optimal performance and lifespan, avoid deep discharges and keep the battery charged between 20% and 80% during storage.
  • Regularly check the battery terminals for secure connections to prevent power loss or overheating.
  • If using the battery in extreme temperatures, ensure it is within the specified operating range to prevent performance degradation or safety issues.

11. Warranty & Support

11.1 Warranty Terms

  1. Warranty Period: 1 year from the date of purchase (or 300 cycles, whichever comes first).
  2. Warranty Scope: Product quality issues (e.g., excessive cell capacity attenuation, BMS failure), excluding damage caused by human error, misuse, modification, or natural disasters.
  3. Warranty Service: Within the warranty period, after detection and confirmation, free repair or replacement service is available.
  4. Disclaimer: The manufacturer is not liable for product damage or personal injury caused by violating the operation specifications in this manual.

11.2 Version History

Version No. Revision Date Revision Content
V1.0 2026-05-10 Initial release

11.3 Additional Resources

For a complete user manual in PDF format, please refer to the official document: User manual (PDF)

12. Environmental Protection & Recycling

12.1 Environmental Statement

This product complies with the WEEE Directive (2012/19/EU) and RoHS Directive, and does not contain harmful substances such as lead, mercury, and cadmium. After the product is scrapped, it shall not be discarded at will; it must be handled by professional recycling institutions to prevent environmental pollution.

12.2 Recycling Channels

  • Contact the manufacturer: Call customer service for free recycling.
  • Local recycling points: Deliver to designated battery recycling centers or e-waste recycling points.
  • Dealer recycling: Assist in recycling through the dealer where the product was purchased.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.