1. Important Safety Information
Read all instructions carefully before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Warning: Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- Do not expose to water or moisture (though made of stainless steel, proper care is advised).
- Handle with care to avoid cuts or injuries.
2. Product Overview
These air intake covers are designed to enhance the aesthetic appeal of your BMW R nineT motorcycle while providing a layer of protection to the air intake area. Made from high-quality stainless steel, they offer durability and a sleek finish.
Features:
- Front air intake trim cover.
- Enhances motorcycle aesthetics.
- Provides protection and durability for the air intake area.
- Easy to install.
- Material: High quality stainless steel.
- Condition: 100% brand new.
- Quantity: A pair (for both sides of the motorcycle).
- Color: Silver.
Fitment:
- For BMW R NINE T
- For BMW R NINE T Pure
- For BMW R NINE T Urban
- For BMW R NINE T Scrambler
Note: These covers are specifically designed for the R nineT series and may not fit other BMW models like the R1200 GSA 2008.
3. Setup and Installation
Installation of the air intake covers is straightforward. Please follow these steps:
- Ensure your motorcycle is turned off and cooled down before beginning installation.
- Identify the air intake area on both sides of your motorcycle.
- Carefully position each cover over the respective air intake. The covers are designed to fit snugly.
- Secure the covers using the provided fasteners or clamps. Ensure they are tight but do not overtighten to avoid damage.
- Verify that the covers are firmly in place and do not obstruct any moving parts or other components.
Refer to the images below for visual guidance on installation and the appearance before and after installation.
Figure 3.1: Comparison of the motorcycle's air intake area before and after installing the covers.
Figure 3.2: Close-up view of the installed air intake cover.
Figure 3.3: View of the air intake cover installed on the motorcycle.
Installation Video:
Video 3.1: A short demonstration of the air intake cover installation process.
4. Operating Instructions
These air intake covers are passive accessories. Once correctly installed, they require no further operation. Their primary function is to provide aesthetic enhancement and a degree of protection to the motorcycle's air intake system.
5. Maintenance
To ensure the longevity and appearance of your stainless steel air intake covers, follow these maintenance guidelines:
- Cleaning: Wipe the covers regularly with a soft, damp cloth to remove dust and road grime. For stubborn dirt, use a mild soap solution and rinse thoroughly. Avoid abrasive cleaners or harsh chemicals that could scratch the surface.
- Inspection: Periodically check the covers for any signs of damage, scratches, or loose fittings. Ensure all fasteners remain secure.
- Polishing: If desired, a stainless steel polish can be used to maintain the shine and protect against minor blemishes.
Figure 5.1: The stainless steel construction ensures durability and ease of maintenance.
6. Troubleshooting
While these covers are simple accessories, here are some common issues and their solutions:
- Loose Cover: If a cover feels loose, check the fasteners. Tighten them gently until secure. Do not overtighten.
- Scratches/Dents: Minor scratches on the stainless steel can sometimes be buffed out with a fine-grit polishing compound designed for stainless steel. For significant damage, replacement may be necessary.
- Improper Fit: Double-check that the covers are installed on the correct motorcycle model (BMW R nineT series). If the fit is still incorrect, ensure no other components are obstructing the installation.
7. Specifications
| Attribute | Detail |
|---|---|
| Product Name | Motorcycle Air Intake Covers |
| Brand | Otilli |
| Model Compatibility | BMW R NINE T, R NINE T Pure, R NINE T Urban, R NINE T Scrambler |
| Material | High quality stainless steel |
| Color | Silver |
| Quantity | A pair (2 pieces) |
| Package Dimensions (L x W x H) | 20 cm x 18 cm x 6 cm |
| Package Weight | 0.297 kg |
8. User Tips
- Easy Upgrade: Many users appreciate the straightforward installation process, making it a quick and effective aesthetic upgrade.
- Enhanced Look: The covers are noted for giving the motorcycle a sportier and more aesthetically pleasing appearance.
- Quality Material: The good quality material ensures durability and a premium feel.
9. Frequently Asked Questions (FAQ)
- Q: Will these covers fit a BMW R1200 GSA 2008?
- A: No, these air intake covers are specifically designed for the BMW R NINE T, R NINE T Pure, R NINE T Urban, and R NINE T Scrambler models. They are not compatible with the R1200 GSA 2008.
- Q: Are these sold as a pair, for both sides of the motorcycle?
- A: Yes, the product includes a pair of covers, one for each side of the motorcycle's air intake.
10. Manufacturer & Support
For further assistance or inquiries, please contact the manufacturer or authorized representative:
Manufacturer:
- Company: Guangzhou Otili Trading Co., Ltd
- Address: Nanhai District, Foshan City, Guangdong Province, Dali Town, Fengxiu Building, 9th Floor
- Email: 243226686@qq.com
EU Authorized Representative:
- Name: VAT SPEED SL
- Address: Calle Antonio Salvador N99.1, 28026 Madrid, Spain
- Tel: +34-916321924
- E-mail: services@vatspeed-eu.com
A detailed user manual in PDF format is also available for download: View User Manual (PDF)