1. Product Overview
This manual provides basic usage guidelines for the PowerMotor SUR-001 Front Number Plate Holder, designed for SURRON Lightbee S X Dirt E-Bikes. This accessory serves as a mounting point for your motorcycle's front license plate, ensuring compliance and visibility. Due to the wide variety of motorcycle accessories, specific details may vary depending on the product type, but the following guidelines will help you properly install, use, and maintain this accessory.
Video: 360-degree view of the PowerMotor SUR-001 Front Number Plate Holder.
2. Safety Warning
Read and understand: Before using any accessories, please read this manual and the specific guide that comes with the product in detail.
Professional installation: Unless you have the corresponding skills, it is recommended that professional technicians install it.
Suitability: Make sure the accessories match your motorcycle model, year, and specifications.
Personal protection: Wear appropriate protective equipment when installing or replacing accessories.
Comply with regulations: Make sure all accessories comply with local traffic regulations.
3. Precautions
Avoid incompatible accessories: Do not use accessories that are incompatible with your motorcycle.
Professional Repair: If the accessories are damaged or the performance is degraded, please stop using them immediately and seek professional repair.
4. Setup and Installation
The PowerMotor SUR-001 Front Number Plate Holder is designed for straightforward installation using zip ties (included). Ensure your motorcycle's front area has suitable mounting points.
4.1. Package Contents
- 1x PowerMotor SUR-001 Front Number Plate Holder
- 4x Zip Ties
4.2. Installation Steps
- Prepare the Area: Ensure the front of your motorcycle is clean and free from obstructions where the number plate holder will be mounted.
- Position the Holder: Place the number plate holder in the desired position on the front of your motorcycle. Identify suitable attachment points on your bike's frame or existing structures.
- Secure with Zip Ties: Thread the provided zip ties through the designated slots on the number plate holder and around the motorcycle's mounting points. Pull the zip ties tight to secure the holder firmly in place. Ensure there is no wobble.
- Trim Excess: Trim any excess length from the zip ties for a neat finish.
- Attach Number Plate: Once the holder is securely mounted, attach your official number plate to the holder using appropriate fasteners (not included, typically screws or bolts).

Image: Front view of the number plate holder with included zip ties for mounting.

Image: Side view of the number plate holder, illustrating its profile and attachment points.
5. Operating Instructions
The number plate holder functions by securely displaying your motorcycle's front license plate. Once installed, ensure your license plate is firmly attached to the holder and remains visible according to local regulations.
6. Maintenance
- Regular Inspection: Periodically check the number plate holder for any signs of damage, cracks, or loose connections.
- Secure Attachment: Ensure the zip ties remain tight and the holder is firmly attached to the motorcycle. Re-tighten or replace zip ties if they become loose or show wear.
- Cleaning: Clean the plastic holder with a soft cloth and mild soap and water. Avoid abrasive cleaners or solvents that could damage the plastic finish.
7. Troubleshooting
7.1. Number Plate Holder is Loose
- Check Zip Ties: Inspect the zip ties. If they are loose, re-tighten them. If they are damaged or worn, replace them with new, strong zip ties.
- Inspect Mounting Points: Ensure the motorcycle's mounting points are intact and provide a secure base for the holder.
7.2. Number Plate is Loose on Holder
- Check Fasteners: Ensure the screws or bolts used to attach the number plate to the holder are tight.
- Inspect Holder Slots: Verify that the slots or holes on the holder for the number plate fasteners are not stripped or damaged.
7.3. Holder is Damaged
- If the holder is cracked, broken, or significantly damaged, it should be replaced to ensure the secure display of your number plate.
8. Specifications
| Feature | Specification |
|---|---|
| Brand Name | PowerMotor |
| Model Name | SUR-001 |
| Item Type | Registration Plate Holder |
| Material | Plastic |
| Item Weight | 0.12 kg |
| Origin | Mainland China |
| Top Width | 170 mm / 6.69 in |
| Height | 180 mm / 7.08 in |
| Bottom Width | 192 mm / 7.55 in |
| Mounting Hole Diameter | 7 mm / 0.27 in |
| Package Dimensions (approx.) | 20 cm (L) x 20 cm (W) x 7 cm (H) |
| Package Weight (approx.) | 0.14 kg |

Image: Dimensional diagram of the SUR-001 Front Number Plate Holder.
9. User Tips
- Always ensure all fasteners, including zip ties and number plate screws, are tight before riding to prevent loss or damage.
- Regularly clean the holder to maintain its appearance and ensure maximum visibility of your number plate.
10. Warranty and Support
For warranty information, please refer to the terms and conditions provided by your retailer or contact PowerMotor directly. Keep your proof of purchase for any warranty claims.
For additional general guidelines on motorcycle accessories, you may refer to the provided PDF user manual: View General Motorcycle Accessories Manual (PDF).