GTI Car Door Corner Cover

Contents

Car Door Corner Cover Bumper Protector User Manual

Model: Car Door Corner Cover | Brand: GTI

1. Product Overview

The Car Door Corner Cover Bumper Protector is a self-adhesive accessory designed to protect your vehicle's door edges from scratches, chips, and minor impacts. Made from high-quality soft rubber, these covers provide a durable and discreet layer of protection, especially useful in tight parking spaces or when opening doors near obstacles. They are specifically designed for vehicles with 90-degree angle door corners.

Main product image showing two black car door corner covers and one installed on a white car door.
Car Door Corner Covers in black, with one installed on a white car door for illustration.

2. Specifications

Feature Detail
Type Bumper Collision Bar / Car Door Corner Cover
Material Soft Rubber (Silicone)
Dimensions (approx.) 6.7 cm x 5.8 cm x 4.5 cm (Length x Height x Width)
Color Options Transparent, Black
Package Contents 2 or 4 Car Door Corner Covers (depending on selection)
Compatibility For Volkswagen models including 4 Motion, Blue Motion, Caddy, Golf 4, 5, 6, 7, Bora, Beetle, Touran, Tiguan, Jetta, GTI, R Line, R32, Touareg, Passat, Polo, Magotan, Lavida, Lamando, Tharu, Sagitar, Santana, TAYRON, Teramont, T-Cross, VILORAN. Only applicable to vehicles with 90-degree angle door corners.
Diagram showing dimensions of the car door corner cover (58mm, 67mm, 45mm) in both transparent and black versions.
Dimensions of the Car Door Corner Cover.

3. Setup and Installation

Before installation, ensure the product is suitable for your car's door corners. This product is designed for 90-degree angle door corners only.

Image showing a white car with an arrow pointing to the installation location on the door edge, and three smaller images below: one with a checkmark showing a suitable door edge, and two with crosses showing unsuitable door edges (rounded or with existing trim).
Installation location and compatibility check for door corners.

Installation Steps:

  1. Clean the Surface: Thoroughly clean the car door corner where the protector will be applied. Ensure the surface is free from dust, dirt, grease, and moisture. Use an alcohol wipe for best results and let it dry completely.
  2. Inspect the Protector: Open the packaging and inspect each corner cover for any manufacturing defects or damage.
  3. Positioning: Carefully align the protector with the door corner. Ensure it fits snugly and covers the desired area.
  4. Peel and Stick: Remove the protective film from the adhesive backing of the corner cover.
  5. Apply: Press the protector firmly onto the cleaned door corner. Apply even pressure for a few seconds to ensure good adhesion.
  6. Curing Time: Avoid washing the car or exposing the installed protectors to heavy rain for at least 24 hours to allow the adhesive to fully cure.
Hand applying a transparent car door corner cover.
Applying the self-adhesive protector to the car door corner.
Comparison image: 'Before installation' showing a car door corner prone to bumps, and 'After installation' showing the protector in place.
Visual comparison of a car door corner before and after protector installation.

4. Operating Instructions

The car door corner covers are passive protective devices. Once installed correctly, they require no active operation. Their function is to absorb impact and prevent damage to your car's paintwork and body when the door comes into contact with other objects.

5. Maintenance

  • Cleaning: Clean the door corner protectors regularly with mild soap and water, or your usual car wash solution. Avoid harsh chemicals or abrasive cleaners that could damage the material or adhesive.
  • Inspection: Periodically check the protectors for any signs of wear, tear, or loosening of the adhesive. If a protector becomes damaged or starts to peel off, it should be replaced to ensure continued protection.

6. Troubleshooting

  • Protector not adhering properly: Ensure the installation surface was thoroughly cleaned and dry before application. Cold temperatures can affect adhesive performance; try warming the surface and the protector slightly before application.
  • Protector falling off: This usually indicates improper installation or a compromised adhesive. Re-clean the surface and apply a new protector, ensuring firm and even pressure during application.
  • Protector doesn't fit: This product is designed for 90-degree angle door corners. If your car's door corners are rounded or have existing trim that interferes, the protector may not fit correctly. Verify compatibility before purchase.

7. User Tips

  • For optimal adhesion, install the protectors in a warm environment.
  • Double-check the door corner angle before purchasing to ensure compatibility.
  • Consider purchasing a 4-piece set to protect all four doors, even if you primarily use the front doors.

8. Warranty and Support

For specific warranty information, return policies, or further support regarding this product, please refer to the seller's terms and conditions at the time of purchase. A user manual in PDF format may be available for download from the seller's product page: User Manual (PDF). Please note that the content of the linked PDF may pertain to a different product and should be verified for relevance.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.