GTI Car Door Corner Cover Anti-Scratch Protector Bumper Sticker

Contents

GTI Car Door Corner Cover Anti-Scratch Protector Bumper Sticker User Manual

1. Introduction

Thank you for choosing the GTI Car Door Corner Cover Anti-Scratch Protector Bumper Sticker. This product is designed to provide protection and enhance the appearance of your vehicle's door corners, preventing scratches and minor collision damage. Made from high-quality, environmentally friendly silicone, it offers a simple and effective solution for maintaining your car's pristine condition.

2. Safety Information

  • Ensure the installation surface is clean and dry before applying the sticker to ensure proper adhesion.
  • Avoid applying the product in extreme temperatures (too hot or too cold) as this may affect adhesion.
  • Keep out of reach of children.

3. Product Overview

The Car Door Corner Cover is a self-adhesive bumper collision bar designed for specific car models.

Two black car door corner covers installed on a white car door

Figure 1: GTI Car Door Corner Covers installed on a vehicle.

Key Features:

  • 100% Brand new and high quality.
  • Provides decoration and protection for your car.
  • Made from high-quality, environment-friendly, and high-temperature resistant silicone.
  • Self-adhesive design for easy application.

4. Installation Instructions

This product is specifically designed for vehicles with 90-degree angle door corners. Please verify your car's door corner shape before installation.

Diagram showing correct and incorrect installation locations for car door corner covers

Figure 2: Correct installation location on a 90-degree door corner (left) versus incorrect locations (middle and right).

Installation Steps:

  1. Clean the Surface: Thoroughly clean the car door corner where the protector will be applied. Use a mild detergent and water, then dry completely. Ensure there is no dust, grease, or wax on the surface.
  2. Positioning: Carefully align the corner cover with the 90-degree angle of your car door corner.
  3. Peel and Stick: Peel off the protective backing from the adhesive side of the cover.
  4. A hand peeling the protective backing off a transparent car door corner cover

    Figure 3: Peeling off the adhesive backing.

  5. Apply Firmly: Press the cover firmly onto the car door corner, ensuring good contact with the surface. Apply pressure for a few seconds to secure adhesion.
  6. Close-up view of a black car door corner cover securely installed

    Figure 4: Installed car door corner cover.

  7. Allow to Cure: For best results, avoid washing your car or exposing the installed covers to heavy moisture for at least 24 hours after installation.

5. Care and Maintenance

  • Regularly clean the covers with mild soap and water to remove dirt and grime.
  • Avoid using harsh chemicals or abrasive cleaners, as these may damage the silicone material or affect its appearance.
  • Inspect the covers periodically for any signs of wear or damage. If a cover becomes loose or damaged, consider replacing it to maintain optimal protection.

6. Troubleshooting

No specific troubleshooting steps are provided by the manufacturer for this product. However, if you encounter issues, consider the following general advice:

  • Poor Adhesion: If the cover does not stick well, ensure the surface was thoroughly cleaned and dried before application. Re-clean the area and try applying a new cover. Extreme temperatures during installation can also affect adhesion.
  • Cover Falling Off: This usually indicates poor initial adhesion. Ensure the surface is flat and at a 90-degree angle, and that sufficient pressure was applied during installation.
  • Damage/Wear: If the cover is damaged, it should be replaced to ensure continued protection.

7. Specifications

Attribute Detail
Product Type Car Door Corner Cover / Bumper Collision Bar
Brand Name GTI
Material Soft Rubber (Silicone)
Dimensions (approx.) 6.7 cm (length) x 5.8 cm (height) x 4.5 cm (width)
Colors Available Transparent, Black
Package Quantity 2 or 4 pieces
Compatibility For Volkswagen models with 90-degree door corners (e.g., Golf, Caddy, Passat, Tiguan, Jetta, etc.)
Origin Mainland China
Diagram showing the dimensions of the car door corner cover

Figure 5: Product dimensions.

8. User Tips

  • For optimal adhesion, ensure the car's surface is at a moderate temperature during installation. Avoid very cold or very hot conditions.
  • Consider using a hair dryer on a low setting to gently warm the adhesive before application, especially in cooler weather, to improve stickiness.
  • Apply the covers symmetrically on both sides of the car for a balanced aesthetic.

9. Warranty and Support

Specific warranty details for this product are not provided in the product description. For any questions regarding warranty, returns, or product support, please contact the seller directly through your purchase platform.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.