HTBCCHB Motorcycle Cooling Fan Oil Cooler Engine Electric Radiator

Contents

12V Motorcycle Cooling Fan Oil Cooler Engine Electric Radiator User Manual

Model: Motorcycle Cooling Fan Oil Cooler Engine Electric Radiator

1. Product Information

This manual provides instructions for the 12V Motorcycle Cooling Fan Oil Cooler Engine Electric Radiator.

  • Product Name: Oil Cooler Engine Radiator Electric Cooling Fan
  • Brand: HTBCCHB
  • Manufacturer: Yongkang Hongtian Trading Co., Ltd. Changcheng Village, Yongkang Economic Development Zone, Jinhua City, Zhejiang Province Room 302, 3rd Floor, No. 66 Jinbi Road
  • Manufacturer Contact: 841996743@qq.com, 86-13018090962
  • EU Authorized Representative: MJCM SARL, 78 avenue des Champs Elysees Bureau 326
  • EU Representative Contact: mjcm190928@gmail.com, 33-767213611

This product is a component of the engine cooling system for motor vehicles, complying with the EU Electromagnetic Compatibility (EMC) Directive 2014/30/EU and the Machinery Safety Regulation 2006/42/EC, meeting the sales standards for the EU market.

2. Safety & Warnings

Please read all instructions carefully before use. Failure to follow these instructions may result in engine overheating, vehicle malfunction, and safety hazards.

  • Professional Installation Requirement: This product must be installed by a professional technician qualified in motorcycle/ATV maintenance. Operation by untrained personnel may cause incorrect wiring, short circuits, and fire risks.
  • Wiring Requirement: The positive and negative poles must be connected correctly; reverse connection is prohibited. Insulation protection must be provided after wiring to prevent short circuits and electric leakage.
  • Installation Inspection: After installation, verify that the fan operates properly without abnormal noise or jamming, and ensure the cooling effect meets standards. Do not operate the vehicle on the road otherwise.
  • Load Limit: Overloading and prolonged high-speed operation are prohibited to prevent motor burnout due to overheating.
  • Children Warning: Keep this product out of the reach of children to avoid pinching injuries and electric shock risks.
  • Waterproof Requirement: Avoid directly flushing the motor with a high-pressure water gun to prevent water ingress, short circuits, and motor burnout.

3. Setup (Installation)

3.1. Installation Preparation

  1. Turn off the vehicle power supply and disconnect the negative terminal of the battery to prevent short circuits.
  2. Clean the mounting positions of the radiator / oil cooler, remove oil stains and impurities, and ensure the mounting surface is flat.
  3. Inspect the fan for no external damage, no motor seizure, and intact plugs to confirm it meets installation requirements.

3.2. Installation Steps

  1. Fixed Installation: Secure the fan to the surface of the radiator/oil cooler using 4-corner metal or plastic brackets, and tighten the bolts evenly to ensure the fan fits tightly against the radiator with no looseness.
  2. Wiring Installation: Connect the 300mm wiring harness of the fan to the vehicle's 12V power supply. It is recommended to connect a thermostat switch in series for automatic start and stop. Provide proper insulation protection.
Front view of the 12V motorcycle cooling fan, highlighting universal fit, easy installation, powerful cooling, large airflow, and low noise.
Figure 1: Front view of the cooling fan, emphasizing universal fit and efficient cooling.
Close-up of the fan's electrical connector, showing the wiring interface.
Figure 2: Detail of the electrical connector for wiring.

4. Operating Instructions

4.1. Operation Test

  1. Turn on the power supply to test that the fan runs normally without abnormal noise or jamming.
  2. Confirm the correct air direction.

4.2. Final Inspection

  • Organize and secure the wiring harness to avoid interference with the operation of the engine or shock absorption components, completing the installation.

5. Maintenance and Care

5.1. Storage

  • Uninstalled fans shall be stored in a dry and ventilated environment to prevent moisture and corrosion of the motor.

5.2. Regular Maintenance

  • Regularly clean dust and silt from the fan surface, keep the fan blades clean, and ensure heat dissipation efficiency.
  • Regular Inspection: Check whether the fan operates properly, the wiring is loose, and the fan blades are damaged every 500 kilometers. Repair immediately if any problems are found.
  • Regular Cleaning: Clean dust and oil stains from the surfaces of the fan and radiator once a month to prevent clogging that affects heat dissipation.

5.3. Replacement Cycle

  • Under normal use and maintenance, the service life of the fan is approximately 2 to 3 years. Replace it promptly if abnormal motor noise, reduced speed, or burnout occurs.

5.4. Prohibited Operations

  • Do not forcibly rotate the fan blades by hand to avoid motor damage.
  • Do not run the fan idle while powered on for a long time to prevent motor overheating and burnout.

6. Troubleshooting

This section addresses common issues you might encounter with your cooling fan.

Problem Possible Cause Solution
Fan not operating / No power Incorrect wiring, loose connection, blown fuse, faulty thermostat switch. Check wiring for correct polarity and secure connections. Inspect vehicle's fuse box. Test or replace thermostat switch. Ensure battery is connected.
Abnormal noise or jamming Debris in fan blades, damaged blades, motor seizure, improper mounting. Inspect fan blades for obstructions or damage and clean. Ensure fan is securely mounted without looseness. If motor is seized, replacement may be necessary.
Reduced cooling effect / Overheating Clogged fan/radiator, reduced fan speed, motor burnout, improper air direction. Clean fan blades and radiator surfaces. Check fan for proper rotation and speed. Verify correct air direction. Avoid overloading or prolonged high-speed operation.
Electric leakage / Short circuit Improper insulation, reverse wiring, water ingress. Ensure all wiring connections are properly insulated. Verify correct positive and negative pole connections. Avoid direct high-pressure water gun flushing on the motor.

7. Specifications

7.1. General Features

  • Effective engine heat dissipation
  • Prevents engine overheating
  • Square frame design for easy installation
  • High-speed motor with stable performance
  • Durable plastic construction
  • Easy to install and use

7.2. Technical Specifications

Attribute Value
Manufacture China (Mainland China)
Material Metal + Plastic
Voltage DC 12V
Blade Quantity 5 blades
Color Black
Overall Diameter Approx. 180mm
Mounting Type 3-point fixing bracket
Wire Type Two wires (positive/negative) with plug
Battery Included No
High-concerned chemical None

7.3. Package Dimensions & Weight

  • Length: 20 cm
  • Width: 15 cm
  • Height: 10 cm
  • Weight: 0.431 kg
Image showing a tape measure across the fan, indicating an approximate overall diameter of 180mm.
Figure 3: Measurement of the fan's overall diameter.
Side profile view of the electric cooling fan, showing its depth and blade structure.
Figure 4: Side view of the cooling fan.

8. User Tips

  • Always double-check wiring polarity before connecting to avoid damage to the fan or vehicle electrical system.
  • Consider adding a protective mesh or cover if the fan is installed in an area prone to debris accumulation to prolong its lifespan.
  • Regularly check the fan's mounting points for tightness, especially after off-road use, to prevent vibration and potential damage.

9. Warranty & Support

For technical support, warranty inquiries, or any questions regarding the product, please contact the manufacturer or the EU authorized representative directly.

  • Manufacturer Contact: 841996743@qq.com, 86-13018090962
  • EU Authorized Representative Contact: mjcm190928@gmail.com, 33-767213611

A detailed user manual in PDF format is also available for download: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.