VGETTING VGETTING LED Fog Lamp

Contents

VGETTING LED Fog Lamp User Manual

Model: VGETTING LED Fog Lamp

1. Product Overview

The VGETTING LED Fog Lamps are designed to enhance vehicle visibility and safety in various driving conditions. These lamps feature high-brightness LED chips, offering strong light penetration in fog, rain, snow, and dark environments. They provide dual lighting options: white light for daytime running (DRL) to improve vehicle visibility and yellow light for safe driving in adverse weather conditions.

Key Features:

  • High-brightness LED chips for superior illumination.
  • Dual-color functionality: White for DRL, Yellow for fog.
  • Plug-and-play installation for easy setup.
  • Durable ABS housing and high-transmittance PC lens.
  • Waterproof (IP67), dustproof, and shockproof design.
  • Efficient heat dissipation for stable performance and long lifespan.

Compatibility:

  • For Honda Accord 2008-2013
  • For Honda JAZZ / FIT 2012-2014
  • For Honda Civic 2009-2015
VGETTING LED Fog Lamps installed on a car, showing yellow light output and the two lamp units.

Image 1.1: VGETTING LED Fog Lamps (Yellow) and their appearance.

2. Safety & Warnings

Important Safety Information

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture during installation or if not properly sealed.

3. Setup & Installation

These fog lamps are designed for plug-and-play, non-destructive installation.

Step 1: Preparation (Safety First)

  • Park the car steadily and engage the handbrake.
  • Crucially, disconnect the negative cable of the battery before starting any electrical work.

Step 2: Remove Old Fog Lamps

  • Locate the existing fog lamp assembly on your vehicle's front bumper.
  • Carefully disconnect any wiring harnesses attached to the old lamp.
  • Unscrew or unclip any fasteners holding the old lamp in place.
  • Gently remove the old fog lamp assembly.

Step 3: Install New Fog Lamps (Test First, Then Fix)

Close-up of the fog lamp showing its plug-and-play connector.

Image 3.1: Plug-and-Play Connector for Easy Installation.

  • Pre-testing: First, connect the new fog lamp's plug to the original car harness. Reconnect the battery (temporarily). Turn on the power and test whether the fog lights illuminate normally in both white and yellow modes.
  • Formal Installation: After confirming that the function is normal, disconnect the battery again.
  • Align the new fog lamp with its position in the bumper opening and install it.
  • Secure the lamp by tightening any nuts or clips from the inside.
  • Reconnect the electrical plug firmly.
  • Ensure all connections are secure and properly seated.
Before and after installation comparison of the fog lamps on a car.

Image 3.2: Installation Effect (Before and After).

Installation Video Guide

Video 3.1: Product demonstration showing the lamp's features and lighting modes.

4. Operating Instructions

The VGETTING LED Fog Lamps offer two distinct lighting modes:

  • White Light: Functions as Daytime Running Lights (DRL), improving your vehicle's visibility to other drivers during daylight hours.
  • Yellow Light: Provides enhanced visibility and reduces glare in adverse weather conditions such as fog, rain, or snow.
Image showing both yellow and white lighting effects of the fog lamps.

Image 4.1: Two Types of Lighting Effects (Yellow and White).

Yellow lighting effect showing the light source and beam pattern.

Image 4.2: Yellow Light Output.

White lighting effect showing the light source and beam pattern.

Image 4.3: White Light Output.

5. Maintenance

  • Regular Cleaning: Keep the lens of your fog lamps clean from dirt, dust, and road grime to ensure maximum light output and effectiveness. Use a soft cloth and mild cleaning solution.
  • Sealing Inspection: After washing your car or driving through heavy rain, check whether there is any severe water ingress or persistent fogging inside the lamp. Slight fogging that clears up after the lights have been on for a while is normal due to temperature differences. Persistent fogging or water accumulation indicates a potential sealing issue.
  • Connection Check: Periodically inspect the electrical connections to ensure they remain secure and free from corrosion.
Image illustrating the waterproof capabilities of the fog lamp in various weather conditions.

Image 5.1: Waterproof Design for Various Weather Conditions.

6. Troubleshooting

Lights Not Working After Installation:

  • Final Inspection: Reconnect the car battery and perform a final check of all lighting functions (white and yellow modes).
  • Check Connections: Ensure all electrical plugs are securely connected to the vehicle's harness and the fog lamp.
  • Battery Connection: Verify that the car battery is properly reconnected and has sufficient charge.
  • Fuse Check: Consult your vehicle's manual to check the fuse for the fog lights. A blown fuse may prevent the lights from working.

Persistent Fogging or Water Inside Lamp:

  • If fogging does not clear after operation or if water accumulates, this may indicate an improper seal or damage. Re-check the installation to ensure the lamp is seated correctly and any seals are intact.
  • If the issue persists, contact customer support for assistance.

7. Specifications

Attribute Specification
Brand Name VGETTING
Item Type Fog Lamp Assembly
Voltage DC 12V
Lumens 800LM
Light Color White / Yellow (Dual Color)
Light Source High-brightness LED
Material PC Lens + ABS Housing
Waterproof Rating IP67
Certification CCC
Dimensions (Approx.) Length: 14.5 cm (5.71 in), Height: 7.9 cm (3.11 in)
Diagram showing the dimensions of the fog lamp unit.

Image 7.1: Product Dimensions.

8. User Tips

  • Beam Alignment: After installation, ensure the fog lamps are properly aimed. Incorrect alignment can reduce effectiveness or cause glare for oncoming drivers. Adjust as necessary according to your vehicle's specifications.
  • Regular Cleaning: Keep the lamp lenses clean. A clear lens ensures maximum light output and optimal visibility, especially in adverse weather.
  • Check Functionality: Periodically test both white (DRL) and yellow (fog) light functions to ensure they are operating correctly.

9. Warranty & Support

Specific warranty terms for this product are not provided in this manual. For warranty information, technical support, or any product-related inquiries, please contact your seller or the manufacturer directly.

Manufacturer & EU Representative Information:

Manufacturer: Guangzhou Camel Technology Co., Ltd.
No. 4 West Fangxin Road, Fangcun Avenue, Liwan District, Guangzhou City, Guangdong Province, China

EU Authorized Representative: MJCM SAR
78 avenue des Champs Elysees Bureau 326, PARIS.FR
Contact: mjcm190928@gmail.com, +0033 752907452

Importer: Guangzhou Camel Technology Co., Ltd.
No. 4 West Fangxin Road, Fangcun Avenue, Liwan District, Guangzhou City, Guangdong Province, China

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.