HTBCCHB Universal Left Hand Rear Hydraulic Brake Master Cylinder Kit

Contents

Universal Left Hand Rear Hydraulic Brake Master Cylinder Kit

Model: Universal Kit | Brand: HTBCCHB

1. Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your new Universal Left Hand Rear Hydraulic Brake Master Cylinder Kit. Please read this manual thoroughly before installation and use to ensure proper function and safety.

2. Safety & Warnings

  • This product is a modified accessory. Installation must be carried out by professional maintenance personnel. Non-professionals are prohibited from installing it themselves to avoid safety accidents caused by improper installation.
  • This product is only suitable for legal and compliant modification of civilian vehicles. Installation and use must comply with local traffic regulations. Any responsibility arising from illegal modification shall be borne by the user.
  • After installation, a thorough road test must be conducted to confirm that the braking performance is normal before riding. If there is brake failure, abnormal noise, oil leakage, or any other issue, stop using immediately and troubleshoot.
  • When cycling, it is necessary to wear complete protective gear, comply with traffic rules, and drive safely.
  • The product does not contain any toxic, harmful, or prohibited substances and meets environmental standards.
Close-up of the master cylinder reservoir cap with 'WARNING' text.
Figure 1: Master Cylinder Reservoir Cap with Warning Label

3. Package Contents

Please check the package to ensure all components are present and undamaged:

  • 1x Left Hand Rear Hydraulic Brake Master Cylinder Assembly (Lever and Reservoir)
  • 1x Hydraulic Brake Caliper
  • 1x Hydraulic Brake Oil Hose Pipe (approx. 110cm length)
Complete Hydraulic Brake Master Cylinder Kit including lever, hose, and caliper.
Figure 2: Complete Kit Components

4. Specifications

FeatureSpecification
MaterialCNC Aluminum Alloy
Oil Outlet Screw ThreadM10*1.0mm Clockwise
Piston Diameter9.5mm
Hydraulic Oil TypeMINERAL-OIL
Installation Handlebar Diameter7/8" (22mm)
Hose Pipe Screw SizeM10*1.0mm Clockwise
Hose Pipe Diameter7.5mm
Hose Pipe Length110cm
Item Weight0.53kg
External Testing CertificationISO9001

Compatibility: This is a universal product. It is compatible with various models including KTM 125-500 SX/SX-F/XC/XC-W/XCF-W/XC-F/EXC/EXC-F TPI 6Days, Husqvarna 125-501 TE/FE/TC/FC/TX/FX, and Gas Gas 250/300 EC/EX/MC. Please refer to the product dimensions for exact fitment. The clutch handle provided is designed to fit only with the included clutch cylinder.

5. Setup & Installation

Installation should be performed by professional maintenance personnel.

  1. Dismantling Original Components: Remove the original brake pedal pump and original brake oil pipe from the rear of the vehicle. Clean any oil stains and impurities at the installation position thoroughly.
  2. Install the Upper Pump (Handle End): Fix the upper pump on the left side of the handlebar (left-hand position). Tighten the fixing screws, ensuring that the handle moves smoothly without jamming.
  3. Install the Lower Pump (Caliper End): Fix the lower pump (caliper) in the corresponding installation position of the rear rocker arm/frame of the vehicle. Align it with the brake disc, ensuring that the clearance between the caliper and the brake disc is uniform and friction-free.
  4. Connect the Brake Oil Pipe: Tighten both ends of the braided oil pipe to the upper and lower pump joints respectively. Install a dust cover to prevent mud and sand from entering the connections.
Top view of the brake lever assembly, showing mounting points.
Figure 3: Brake Lever Assembly (Upper Pump)
Hydraulic Brake Master Cylinder Kit with caliper positioned to the right, showing hose connection.
Figure 4: Brake Kit with Hose and Caliper (Lower Pump)

6. Operating Instructions (Brake Bleeding & Testing)

  1. Evacuate the Pipeline Air (Key Step - Brake Bleeding):
    • Inject DOT 4 brake oil into the upper pump reservoir.
    • Open the lower pump exhaust screw (bleeder valve) on the caliper.
    • Slowly pinch the brake lever and repeat multiple times until continuous and bubble-free brake oil flows out of the exhaust port.
    • Once the oil is clear and free of bubbles, tighten the exhaust screw.
  2. Final Oil Fill & Leak Check: Fill the brake oil in the oil storage tank to the appropriate level. Cover the oil tank cover securely. Check for any leaks throughout the entire system.
  3. Test After Installation:
    • Pinch the brake lever multiple times to confirm that the brake feels tight and there is no virtual position (sponginess).
    • Start the vehicle and test the braking performance at low speed.
    • Confirm that the braking is sensitive and there is no abnormal noise.

Video 1: Product showcase demonstrating the brake kit components and basic function.

7. Maintenance

  • Brake Fluid: Regularly check the brake fluid level in the reservoir. Top up with DOT 4 MINERAL-OIL as needed. Replace brake fluid according to your vehicle manufacturer's recommendations, typically every 1-2 years, to prevent moisture contamination.
  • Inspections: Periodically inspect the brake hose for any signs of wear, cracks, or leaks. Check all connections for tightness. Inspect the brake lever for smooth operation and the caliper for proper function.
  • Cleaning: Keep the brake components clean, especially around the caliper and master cylinder, to prevent dirt and debris from entering the system.

8. Troubleshooting

ProblemPossible CauseSolution
Spongy Brake Lever / Poor BrakingAir in the hydraulic systemRe-bleed the brake system thoroughly (refer to Operating Instructions).
Brake Fluid LeakageLoose connections, damaged hose, or faulty sealsCheck all connections for tightness. Inspect the hose for damage. If seals are suspected, professional inspection is required.
Abnormal Noise During BrakingContaminated brake pads, misaligned caliper, or worn componentsInspect brake pads and disc for contamination. Check caliper alignment. Professional inspection may be needed.
Brake Lever Stiff / Not ReturningContaminated fluid, seized piston, or mechanical obstructionCheck for obstructions. If fluid or piston issues are suspected, professional service is recommended.

If you encounter persistent issues, consult a professional motorcycle mechanic.

9. User Tips

  • Always use the specified DOT 4 MINERAL-OIL for your hydraulic brake system. Mixing different types of brake fluid can cause damage to seals and lead to brake failure.
  • When bleeding brakes, ensure the master cylinder reservoir remains topped up to prevent air from being drawn back into the system.
  • After any brake work, always perform a few slow-speed test stops in a safe area before riding at normal speeds.

10. Warranty & Support

For any questions or support regarding this product, please contact your retailer or the manufacturer. Keep your purchase receipt as proof of purchase.

This product complies with general safety standards for motorcycle modification accessories. All materials and processes meet compliance requirements for cross-border e-commerce auto parts categories.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.