1. Introduction
This manual provides essential information for the safe and effective installation, operation, and maintenance of your HTBCCHB 12V Electric Cooling Fan. This fan is designed to enhance the cooling system of 200cc, 250cc, and 300cc motorcycles, ATVs, and quads, functioning as an oil cooler or engine radiator fan. Please read all instructions carefully before use to ensure proper function and prevent potential hazards.
2. Safety & Warnings
Failure to follow these instructions may result in engine overheating, vehicle malfunction, and safety hazards.
- Professional Installation Requirement: This product must be installed by a professional technician qualified in motorcycle/ATV maintenance. Operation by untrained personnel may cause incorrect wiring, short circuits, and fire risks.
- Wiring Requirement: The positive and negative poles must be connected correctly; reverse connection is prohibited. Insulation protection must be provided after wiring to prevent short circuits and electric leakage.
- Installation Inspection: After installation, verify that the fan operates properly without abnormal noise or jamming, and ensure the cooling effect meets standards. Do not operate the vehicle on the road otherwise.
- Load Limit: Overloading and prolonged high-speed operation are prohibited to prevent motor burnout due to overheating.
- Children Warning: Keep this product out of the reach of children to avoid pinching injuries and electric shock risks.
- Waterproof Requirement: Avoid directly flushing the motor with a high-pressure water gun to prevent water ingress, short circuits, and motor burnout.
3. Specifications
| Feature | Detail |
|---|---|
| Product Name | Oil Cooler Engine Radiator Electric Cooling Fan |
| Brand Name | HTBCCHB |
| Origin | Mainland China |
| Material | Plastic + Metal |
| Voltage | DC 12V |
| Blade Quantity | 7 blades |
| Color | Black |
| Wire Type | Two wires (positive/negative) with plug |
| Battery Included | No |
| High-concerned chemical | None |
| Overall Width | 172mm |
| Mounting Hole Distance | 155mm |
| Fan Blade Diameter | 144mm |
| Overall Depth | 53mm |
| Motor Housing Thickness | 40mm |
4. Setup (Installation)
4.1. Installation Preparation
- Turn off the vehicle power supply and disconnect the negative terminal of the battery to prevent short circuits.
- Clean the mounting positions of the radiator / oil cooler, remove oil stains and impurities, and ensure the mounting surface is flat.
- Inspect the fan for no external damage, no motor seizure, and intact plugs to confirm it meets installation requirements.
4.2. Installation Steps
- Fixed Installation: Secure the fan to the surface of the radiator/oil cooler via the mounting holes, tighten the bolts evenly to ensure the fan fits tightly against the radiator without looseness.
- Wiring Installation: Connect the 2-pin plug of the fan to the vehicle's 12V power supply. A thermostat switch is recommended to be connected in series for automatic temperature-controlled start and stop. Provide proper insulation protection for all connections.
- Operation Test: Turn on the power supply to test that the fan runs normally without abnormal noise or jamming, and confirm the correct air direction.
- Final Inspection: Organize and secure the wiring harness to avoid interference with engine operation, completing the installation.
5. Operating Instructions
Once properly installed and wired, the electric cooling fan operates automatically, especially when connected in series with a thermostat switch. The fan's primary function is to draw air through the radiator or oil cooler, facilitating heat dissipation and preventing engine overheating.
- Ensure the fan rotates in the correct direction to pull air through the cooling component for optimal efficiency.
- Monitor engine temperature, especially during prolonged use or in demanding conditions, to confirm effective cooling.
6. Maintenance & Care
- Regular Inspection: Check whether the fan operates properly, the wiring is loose, and the fan blades are damaged every 500 kilometers. Repair immediately if any problems are found.
- Regular Cleaning: Clean dust and oil stains from the surfaces of the fan and radiator once a month to prevent clogging that affects heat dissipation.
- Replacement Cycle: Under normal use and maintenance, the service life of the fan is approximately 2 to 3 years. Replace it promptly if abnormal motor noise, reduced speed, or burnout occurs.
- Prohibited Operations: Do not forcibly rotate the fan blades by hand to avoid motor damage; do not run the fan idle while powered on for a long time to prevent motor overheating and burnout.
Storage and Maintenance for Uninstalled Fans
Uninstalled fans shall be stored in a dry and ventilated environment to prevent moisture and corrosion of the motor.
7. Troubleshooting
- Fan not turning on: Check all wiring connections, ensure the power supply is active, and inspect the thermostat switch (if installed) for proper function.
- Abnormal noise: Turn off the vehicle and carefully inspect the fan blades for any obstructions or damage. If no obstruction is found, the motor may require professional inspection.
- Reduced cooling performance: Ensure the fan blades and radiator fins are clean and free of dust, dirt, or debris. Verify that the fan is rotating in the correct direction to pull air through the cooling component.
8. User Tips
- For optimal performance and safety, consider having the fan installed by a professional technician.
- Regularly check for debris accumulation on the fan and radiator to maintain cooling efficiency.
- Ensure all electrical connections are secure and properly insulated to prevent short circuits and ensure longevity.
9. Warranty & Support
For warranty information, technical support, or any product-related inquiries, please contact the manufacturer or their authorized representatives:
- Manufacturer: Yongkang Hongtian Trading Co., Ltd.
- Manufacturer Contact: 841996743@qq.com, 86-13018090962
- EU Authorized Representative: MJCM SARL
- EU Representative Contact: mjcm190928@gmail.com, 33-767213611