IKSLED 6008-No Hole IR Scan Sweep Hand Sensor Switch

Contents

IKSLED 6008 Hand Wave Sensor Switch User Manual

Model: 6008-No Hole IR Scan Sweep Hand Sensor Switch

1. Product Introduction

The IKSLED 6008 is a hand-wave sensing control board with an integrated LED strip, specifically designed for low-voltage LED applications. It supports hidden installation without the need for drilling holes, making it ideal for cabinet lights, linear lights, and similar scenarios. With its sensitive induction capabilities, you can effortlessly control the light by waving your hand without direct contact. This product is designed for easy installation and is compatible with various aluminum profiles.

For a detailed visual guide and additional information, please refer to the official user manual PDF: User Manual (PDF).

2. Setup and Installation

2.1. Safety Precautions

  • Always ensure the power supply is disconnected before performing any wiring or installation to prevent electric shock or damage to components.
  • This product is designed for DC 12V input only. Do not connect it to other voltage power supplies to avoid burning components.

2.2. Wiring Instructions

The product features clearly marked positive (+) and negative (-) poles for both the power input and the LED light source output. Follow these steps for correct wiring:

  1. Connect the power input positive pole to your DC 12V power supply's positive output.
  2. Connect the power input negative pole to your DC 12V power supply's negative output.
  3. Connect the LED light source's positive pole to the positive input of your lamp circuit.
  4. Connect the LED light source's negative pole to the negative input of your lamp circuit.
Wiring Diagram for IKSLED Hand Wave Sensor Switch

Figure 1: Wiring Diagram - Connect Power and LED Light Source according to positive and negative poles. Note: Welding requires a power failure.

2.3. Installation Steps

The sensor switch module is designed for hidden installation within aluminum profiles:

  1. This module is compatible with 10x10mm and larger aluminum profiles.
  2. Carefully place the light board into the aluminum slot, ensuring it sits stably. No additional drilling is required for the lampshade.
  3. The PC cover of the aluminum profile can be directly placed over the module without affecting the sensing function.
  4. The electronic components are arranged with a 5mm center, cleverly avoiding internal grooves of the aluminum profile.
Installation of Sensor Module in Aluminum Profile

Figure 2: Module installation within a 10x10 aluminum profile. The lampshade does not need to be perforated.

Module Component Placement in Aluminum Profile

Figure 3: 8mm module for 10x10 aluminum, showing how components avoid internal grooves.

3. Operating Instructions

3.1. Hand Wave Sensing

The IKSLED 6008 sensor switch operates via hand-wave induction. To control the light:

  • Turn On/Off: Wave your hand within the sensing distance (1-8cm) to toggle the light on or off.
  • Dimming: The switch supports brightness dimming. Wave your hand and hold it within the sensing range to adjust the brightness.

3.2. Induction Features

  • Strong Penetration: The sensor can detect hand movements through light-transmitting materials, such as PC covers, without requiring holes in the lampshade, maintaining an integrated aesthetic.
  • Strong Anti-interference: The sensor is designed to be stable and reliable, unaffected by reflective objects, mirrors, or mobile phone cameras within the cabinet environment.
  • Sensitive Induction: The switch responds quickly to hand waves within its 1-8cm sensing range, ensuring convenient and efficient operation.
Hand Wave Sensor Features and Hidden Design

Figure 4: Sensor capabilities including penetration through materials, anti-interference, and hidden design.

4. Maintenance and Precautions

  • Power Disconnection: Always disconnect power during any welding or wiring procedures. Live operation is strictly prohibited to prevent short circuits and product damage.
  • Voltage Compatibility: This product exclusively supports DC 12V input. Connecting it to other voltage power supplies will result in component damage.
  • Handle with Care: Avoid bending the light board during installation to prevent damage to the circuit board or dislodging components.
  • Environment: Use this product in a dry environment. Exposure to moisture or water ingress can cause malfunctions.

5. Troubleshooting

If you experience induction failure or if the light does not turn on, please follow these steps:

  1. Check Wiring: Verify that all wiring connections (positive and negative poles for both power and LED light source) are correct and secure.
  2. Power Supply: Ensure that the DC 12V power supply is functioning correctly and providing the specified voltage.
  3. Sensing Area: Check for any obstructions in the sensing area that might be blocking the hand-wave detection.

6. Specifications

Product Parameter Table

Figure 5: Product Parameters Overview

ParameterValue
Product NameNo-drill hand-wave PCB
Model Number6008-No Hole IR Scan Sweep Hand Sensor Switch
Product Size60mm × 8mm
Switch TypeProximity Switch
Induction ModeHand-wave sensing / Empty hand sweep sensing
Input VoltageDC 12V
Output VoltageDC 12V
Sensing Distance1-8cm
Load Current5A
Load Power48W
Delay Time0-1S
Color Temperature3000K (Warm Light), 4000K (Natural Light), 6000K (White Light)
DimmableYes
MaterialPlastic
CertificationRoHS, LVD, EMC, CE
EU LVD VoltageLow voltage: Below 50Vac or 75Vdc

7. User Tips

  • Leverage the

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.