Introduction
This manual provides essential information for the safe and effective installation, operation, and maintenance of your GUTWAREN Common Rail Injector. Please read this manual thoroughly before using the product to ensure optimal performance and longevity.

Figure 1: GUTWAREN Common Rail Injector (Model 0445120177 shown)
1. Setup and Installation
1.1 Pre-Installation Preparation
- Relieve fuel system pressure and disconnect the battery's negative terminal.
- Clean the mounting hole, fuel rail, and cylinder head contact surfaces, ensuring no oil, carbon deposits, or impurities.
- Verify that the injector model and part number match; DO NOT mix different specifications.
- Replace with new O-rings, gaskets, and retaining clips; DO NOT reuse old sealing components.
- Apply a small amount of clean silicone-free oil to the O-rings; do not use sealant.
1.2 Installation Process
- Clean fuel lines and the entire fuel system to avoid impurities.
- Disconnect power and fully relieve fuel system pressure.
- Remove the old injector; carefully check seals, connectors, and the mounting surface for any damage.
- Install the new injector using standard torque specifications; connect wiring correctly and securely.
- Start the engine and carefully check for any fuel leaks, abnormal noise, or vibrations.
- Professional installation is highly recommended due to the precision required.
1.3 Post-Installation Inspection
- Start the engine and confirm there is no fuel leakage.
- Observe stable idling without vibration or unusual odors.
- Electronically controlled injectors require matching, coding, or resetting of learning values using a diagnostic tool.
- Confirm normal acceleration, no black smoke, and no fault lights during a road test.
1.4 Safety Warnings
WARNING: HIGH PRESSURE FUEL SYSTEM! RISK OF FIRE OR PERSONAL INJURY.
- Observe fire prevention measures during disassembly and installation, as fuel is flammable and explosive. Keep away from open flames and static electricity.
- If there is leakage, vibration, or fault light activation after installation, shut down the engine immediately for inspection.
- Professional technicians are recommended for high-pressure common rail/direct injection models.
- DO NOT DISASSEMBLE, MODIFY, OR DAMAGE THE INJECTOR.
- KEEP AWAY FROM OPEN FLAMES, HIGH TEMPERATURE, AND FLAMMABLES.
- DO NOT USE UNQUALIFIED, DAMAGED, OR INCOMPATIBLE PARTS.
- IMPROPER INSTALLATION MAY CAUSE ENGINE FAILURE OR SAFETY HAZARDS.
- OPERATE IN A WELL-VENTILATED AREA.

Figure 2: Angled view of the Common Rail Injector
2. Operating Instructions
2.1 Pre-Startup Check
- Ensure the fuel injector's electrical connector is firmly connected, without looseness or oxidation.
- Check that the fuel line is free of leakage and the O-rings are not aged or damaged.
- For electronically controlled engines, confirm the ECU has no fault codes and the wiring harness is undamaged.
2.2 Key Points for Normal Use
- Use fuel that meets the original factory standards; DO NOT use inferior or water-containing fuel.
- Replace the fuel filter regularly to prevent impurities from wearing the injector's precision components.
- Avoid prolonged idling, frequent startup in low temperatures, and short trips to reduce carbon deposits.
2.3 Shutdown Procedure
- Idle the engine for 1-2 minutes before shutting down to allow the injector to cool.
2.4 Operation Restrictions
- DO NOT strike the injector with a hammer or socket, as it may damage the internal needle valve and coil.
- DO NOT install without replacing sealing components, which will cause oil or air leakage.
- DO NOT over-tighten with excessive torque, as it may crack the fuel rail, cylinder head, or injector body.
- DO NOT allow oil or impurities to enter the injector's interior or nozzle.
2.5 Fuel and Environmental Restrictions
- DO NOT use leaded, water-containing, impurity-containing, or low-grade inferior fuel.
- DO NOT disassemble or install in environments with high temperature, oil contamination, or heavy dust.
- DO NOT allow the injector to run dry or be powered on without fuel for a long time, as it will burn the coil.
3. Maintenance
3.1 Routine Maintenance
- Clean the injector every 20,000-30,000 km; professional cleaning is recommended for direct injection models.
- Replace the fuel filter regularly to prevent impurities from wearing the injector's precision components.
3.2 Maintenance Restrictions
- Non-professionals DO NOT disassemble the injector's internal components (needle valve, spring, solenoid valve).
- DO NOT use ordinary cleaning machines for high-pressure cleaning of direct injection injectors, as it may damage the nozzle.
- DO NOT drive on the road without ECU coding and matching after replacement.
4. Troubleshooting
4.1 Common Issues and Solutions
- Unstable idling, weak acceleration, black smoke, or increased fuel consumption: Immediately inspect the injector system for potential issues.
- Leakage, vibration, or fault light activation after installation: Shut down the engine immediately and perform a thorough inspection to identify and resolve the problem.
5. Specifications
| Feature | Specification |
|---|---|
| Part Name | Common Rail Injector |
| Part Number | 0445120177 (Compatible with 5254261) |
| Brand Name | GUTWAREN |
| Material | Metal |
| Origin | Mainland China |
| Condition | New |
| Purpose | For replace/repair |
| Quality | 100% Professional Tested |
| Type | Common Rail Injector Assembly |
| Size | Standard Size |
| Fuel Type | Diesel |
| Engine Code | Diesel Engine |
| Car Model Fitment | Common Rail System (Universal) |
| Packing | Neutral Package or according to customer's request |
| Minimum Order Quantity (MOQ) | 4 Pieces |
| Delivery Time | Within 3 working Days |
| Shipping Ways | DHL, UPS, FedEx, EMS, TNT, Customer specified |
| Payment Methods | TT, Paypal, Western Union |

Figure 3: Examples of various Common Rail Injectors
6. Warranty and Support
6.1 Warranty Information
This GUTWAREN Common Rail Injector comes with a warranty period of 6-12 Months from the date of purchase.
6.2 Warranty Exclusions
The warranty does not cover damage resulting from improper installation, misuse, neglect, accidents, or unauthorized modifications.
6.3 Customer Support
For any questions, technical assistance, or warranty claims, please contact your dealer or GUTWAREN customer service for support.