1. Introduction
Thank you for purchasing the coolo Tuya ZigBee 24G Human Presence Sensor. This device is a compact, high-precision millimeter-wave radar detector designed to detect both motion and static human presence, including micro-movements like breathing or slight shifts in position. It integrates with smart home systems to enhance automation and security.
Important Note on Protocols: This sensor comes in two main variants:
- Z2M Variant: Exclusively supports Home Assistant Zigbee2MQTT. It is NOT compatible with Tuya/Smart Life App for full presence detection. If connected directly to Tuya/Smart Life, it will function only as a basic PIR (Passive Infrared) motion sensor, not utilizing its 24G presence detection capabilities.
- Tuya Zigbee Variant: Supports both Tuya/Smart Life App and Zigbee2MQTT. Requires a Tuya Zigbee gateway/hub for operation and cannot connect directly via Wi-Fi.
Please ensure you have the correct variant and compatible hub for your intended use.

2. Safety Precautions
- Read this manual carefully before use to ensure correct operation and prevent damage to the device.
- Avoid installing the sensor near strong electromagnetic fields, direct sunlight, or heat sources.
- Do not expose the device to water or excessive humidity.
- Keep out of reach of children.
- If pets or other small animals are present, install the sensor on the side at a height of 1-1.5 meters to avoid false triggers.
- Ensure there are no obstacles directly in front of the sensor lens, as this may affect detection accuracy.
- Avoid installing near moving objects like air conditioners, electric fans, or curtains, which can cause false detections.
3. Package Contents
Please check the box for the following items:
- 1 x Zigbee Occupancy Sensor
- 1 x Double-sided adhesive tape
- 1 x Pin (for reset)
- 1 x User Manual
- 1 x Magnetic Bracket (if included with your variant)
4. Product Overview
The sensor is designed for discreet installation due to its minimum size.

Dimensions: 33mm (1.3in) diameter x 16mm (0.63in) thickness.
5. Setup
5.1. Installation Instructions
The sensor offers flexible installation options:
- Mounting Height: It is recommended to install the product approximately 2.2-3.5 meters above the ground for optimal detection.
- Wall Mounting: Use the provided bracket and adhesive.
- Ceiling Mounting: Use the provided bracket and adhesive.
- Adhesive Mounting: Remove the protective film from the adhesive on the base and stick the device where needed.
- Magnetic Mounting: If your variant includes a magnetic stand, attach the sensor to the stand, and then mount the stand using adhesive or screws. This allows for easy removal for battery changes and flexible aiming.

5.2. Network Configuration (Pairing)
The sensor must be connected to a compatible Zigbee gateway/hub to function correctly and upload data to the server/app.
- Power On: Open the battery cover by rotating it anti-clockwise. Remove the battery insulator film to power on the device.
- Enter Pairing Mode: Press the RESET button (usually a small hole, use the provided pin) for 5 seconds and then release. The red LED indicator will flash rapidly, indicating the device is in pairing mode.
- Add Device in App/Hub: Open your Zigbee gateway's app (e.g., Tuya Smart Life App) or Zigbee2MQTT interface and follow the instructions to add a new device.
- Confirmation: Once successfully paired, the LED indicator will stop flashing, and the device will appear in your app/interface.
6. Operating Instructions
6.1. Detection Capabilities
This 24G radar sensor detects human presence even if there is no movement, including micro-movement states such as sitting still, talking, blinking, or sleeping.


6.2. Smart Home Integration
The sensor can be used to trigger other smart devices, such as smart bulbs, to create automated scenes.

6.3. Function Description & Settings
- LED Indicator: You can turn the LED indicator light on/off via the app. When turned on, it will briefly illuminate to indicate detection.
- Presence Hold Duration: The default duration for someone to be detected (hold time) is 30 seconds. This can be adjusted in the app.
- Sensitivity: The sensor has adjustable sensitivity settings for both motion and static detection. Higher values increase sensitivity and detection distance.
- Protocol Specifics:
- Z2M Variant: Only works with Zigbee2MQTT.
- Tuya Zigbee Variant: Works with Tuya/Smart Life App (via Tuya Zigbee gateway) and Zigbee2MQTT.

7. Maintenance
7.1. Battery Replacement
The sensor is powered by a CR2450 battery.
- Rotate the battery cover anti-clockwise to open it.
- Remove the old CR2450 battery.
- Insert a new CR2450 battery with the correct polarity (+ side up).
- Close the battery cover by rotating it clockwise until secure.
Note: Replacing the battery may reset product parameters and put the device back into pairing mode. You may need to re-pair it with your gateway.
7.2. Cleaning
Wipe the sensor's surface with a soft, dry cloth. Do not use liquid cleaners or abrasive materials.
8. Troubleshooting
- Device not pairing: Ensure the sensor is in pairing mode (LED flashing rapidly) and within range of your Zigbee gateway. Check if your gateway is in pairing mode.
- Frequent false triggers: Review installation location for moving objects (curtains, fans) or pets. Reduce motion detection sensitivity in the app.
- Not detecting static presence: Increase static detection sensitivity in the app. Adjust sensor placement to ensure a clear line of sight to the area of interest. Ensure a strong Zigbee network connection.
- Poor connection/unstable feedback: Ensure the sensor has a strong link quality to your Zigbee network (e.g., link quality above 90). Consider adding Zigbee repeaters if the sensor is far from the gateway.
- Battery drains quickly: High detection frequency or poor network signal can increase battery consumption. Ensure optimal placement and network strength.
- Z2M variant not working with Tuya App: This is expected behavior. The Z2M variant is designed exclusively for Zigbee2MQTT.
9. Specifications
| Parameter | Value |
|---|---|
| Model Number | 24G Presence Sensor |
| Brand Name | coolo |
| Wireless Protocol | Zigbee 3.0 |
| MW Frequency | 24GHz |
| Detection Angle | ≥80° |
| Detection Distance | ≤5m |
| Working Voltage | DC 3V |
| Battery Type | CR2450 (included) |
| Standby Current | <60uA |
| Working Temperature | -10°C to 55°C |
| Working Humidity | 0% to 95%RH (non-condensing) |
| Dimensions | 33mm x 33mm x 16mm |
| Smart Home Platform | Tuya (for Tuya Zigbee variant) |
| Certification | CE, RoHS |
10. User Tips
- Read Instructions: Take a moment to read the instructions carefully before setup; it makes the process much smoother.
- Fine-tune Detection: Utilize the app's settings to fine-tune motion and static detection sensitivity for optimal performance, especially for picking up subtle micro-movements.
- Strong Network Connection: Ensure your sensor has a strong and stable connection to your Zigbee network. Poor link quality (e.g., below 90) can lead to unstable performance.
- Placement for Static Detection: For reliable static presence detection, experiment with sensor placement and sensitivity settings. Sometimes, direct line-of-sight and higher sensitivity are needed.
- Monitor Battery Life: Keep an eye on the battery level. If battery life is shorter than expected, consider optimizing placement for better signal or reducing detection frequency if possible.
11. Warranty and Support
This product comes with a standard manufacturer's warranty. For warranty claims, technical support, or further assistance, please contact your retailer or the manufacturer's customer service. Keep your proof of purchase for warranty purposes.