1. Introduction
This manual provides instructions for the Tedeligo 5301f Wireless Remote Control Switch, a 1-channel relay receiver designed for controlling LED lighting and other compatible devices. The system operates on a 433MHz RF frequency and offers a theoretical remote control distance of up to 1000 meters. It supports various operating modes including Momentary, Toggle, and Latched, allowing for flexible control configurations.
2. Safety Information
- Ensure the input voltage to the receiver matches the specified range (DC 6V-36V or AC 12V-24V). Incorrect voltage can damage the device.
- Do not exceed the maximum current of 10A or maximum load of 360W for the receiver.
- Always disconnect power before performing any wiring or maintenance.
- This device is not a smart device and should not be integrated with smart home systems unless explicitly stated.
- Keep the device away from water and extreme temperatures (-30~+80 Celsius).
3. Package Contents
The package typically includes:
- 1x Wireless Remote Control Transmitter
- 1x 1CH Relay Receiver Module
- 1x 23A 12V Battery (for remote control)
Note: The number of remote controls and receivers may vary based on the specific product variant purchased (e.g., "1 remote 1 receiver", "1 remote 2 receiver", etc.).
4. Specifications
Receiver Specifications:
| Feature | Specification |
|---|---|
| Working Voltage | DC 6V-36V or AC 12V-24V |
| Max Current | 10A |
| Max Load | 360W |
| Quiescent Current | 5mA |
| RF Frequency | 433.92MHz |
| Receiver Size | 28*22*47 mm (1.1*0.87*1.85 in) |
| Working Temperature | -30~+80 Celsius |
| Receiving Sensitivity | >-97dbm |
| Support Encoding | 1527 Learning code / 2262 fixed code |
| RF Operating Mode | ASK superheterodyne wireless reception |
| Amount of Storage Remote Controls | 20 pieces |
Remote Control Specifications:
| Feature | Specification |
|---|---|
| RF Frequency | 433MHz |
| Remote Distance | Up to 1000m (theoretical distance in open space) |
| Material | Plastic |
| Support Encoding | 1527 Learning code |
| Weight | 30g |
| Size | 91mm*40mm |
| Battery | 23A 12V (included) |
5. Setup
5.1 Wiring Diagram
Connect the receiver to your power source and LED lighting as shown in the diagram below. Ensure correct polarity for DC connections (V+ to positive, V- to negative).
5.2 Power On
After wiring, apply power to the receiver. The indicator light on the receiver should illuminate briefly or be ready for pairing.
5.3 Pairing Method (Learning Button)
To pair the remote control with the receiver, follow these steps:
- Power On: Ensure the receiver is powered on (DC 6V-36V or AC 12V-24V).
- Enter Learning Mode: Press the learning button on the receiver module a specific number of times depending on the desired operating mode (see Section 6).
- Press Remote Button: Within 3 seconds, press any button on your remote control.
- Succeed: The receiver's indicator light will flash, confirming successful pairing.
5.4 Setting Default Original State (Power Restoration Behavior)
You can configure the receiver's state after a power outage:
- "Off" state: The light remains off upon repowering.
- "On" state: The light turns on automatically after repowering.
To switch between these two states:
- Press the learning button on the receiver 6 times.
- The indicator LED on the receiver will flash several times and then turn off, indicating successful switching.
Note: Wait 6 seconds after a power outage before repowering to activate this setting.
6. Operating Modes
The relay receiver board has three programmable operation modes:
6.1 Momentary Mode
Description: Press and hold a button on the remote, and the relay will turn on. Release the button, and the relay will turn off.
Programming Steps:
- Press the learning button (on the receiver) 4 times. Wait for 3 seconds.
- Press one button on the remote control. The pairing is successful.
6.2 Toggle Mode
Description: Press a button on the remote once, and the relay will turn on. Press the same button again, and the relay will turn off.
Programming Steps:
- Press the learning button (on the receiver) 2 times. Wait for 3 seconds.
- Press one button on the remote control. The pairing is successful.
6.3 Latched Mode
Description: Press button "A" on the remote, and the relay will turn on. Press button "B" on the remote, and the relay will turn off.
Programming Steps:
- Press the learning button (on the receiver) 3 times. Wait for 3 seconds.
- Press button "A" on the remote control. Wait for 3 seconds.
- Press button "B" on the remote control. The pairing is successful.
Note: The remote control needs to have at least 2 or more buttons to set up latched mode.
6.4 "Many to One" Function
This system supports multiple remote controls operating a single receiver, or a single remote control operating multiple receivers.
7. Resetting the Device
To clear all paired remote controls and reset the receiver to its default state:
- Press the learning button (on the receiver) 8 times.
- The existing data will be deleted successfully.
Note: After resetting, all previously paired remote controls will no longer work and must be re-paired.
8. Maintenance
- Battery Replacement: Replace the 23A 12V battery in the remote control when its voltage is low to ensure strong signal transmission.
- Antenna Adjustment: For better signal reception, slightly stretch the antenna on the receiver.
- Keep the devices clean and free from dust and moisture.
9. Troubleshooting
- Remote not responding: Ensure the receiver is powered on. Check the remote control battery and replace if necessary. Verify that the remote is correctly paired with the receiver.
- Short control distance: Ensure the receiver's antenna is slightly stretched for optimal reception. Avoid obstructions between the remote and receiver.
- Device not turning on/off: Check all wiring connections for proper contact and polarity. Confirm the power supply is within the specified voltage range.
- After resetting, remote controls don't work: This is normal. All remote controls must be re-paired after a reset.
10. User Tips
- Always perform a reset before changing the operating mode of a remote control to avoid conflicts.
- If using Latched mode, ensure your remote control has at least two distinct buttons for ON and OFF functions.
- For optimal range, ensure the receiver's antenna is not coiled or obstructed.
11. Warranty and Support
This product comes with a 1-year warranty from the date of purchase. For technical support or warranty claims, please contact the seller or manufacturer.
Manufacturer: Huizhou Wenqiao Electronic Technology Co., Ltd.
Contact:
- WhatsApp: +86 181 3880 5271 / +86 135 0227 8583
- Email: dieseelectronic@163.com
All emails will be answered within 24 hours.