Tedeligo Mini 220v 10a wireless light switch moudle

Contents

Tedeligo 433MHz Mini Wireless Smart Light Switch and Relay Receiver User Manual

Model: Mini 220v 10a wireless light switch moudle

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Tedeligo 433MHz Mini Wireless Smart Light Switch and 10A Relay Receiver. This system allows for convenient wireless control of various electrical appliances such as lights and fans, offering flexibility and ease of use in homes, offices, and other environments.

Tedeligo Mini Wireless Smart Light Switch and Relay Receiver

Figure 1: Tedeligo Mini Wireless Smart Light Switch and Relay Receiver components.

2. Safety Information

  • WARNING: Always install under power-off conditions. Ensure the main power supply is disconnected before performing any wiring or installation.
  • Be safe when wiring and always keep the power off when wiring.
  • The input and output terminals cannot be reversed. Incorrect wiring can damage the device or cause electrical hazards.
  • Avoid placing the receiver near metal objects, large electronic devices, electromagnetic fields, or other sources of strong interference, as this can affect signal reception and device performance.
  • This device operates at low voltage (below 50Vac or 75Vdc) for its control signals, but the main power supply is AC 85V-250V. Handle with care.

3. Product Overview

3.1 Components

  • Relay Receiver Board: The main control unit that connects to your electrical load (e.g., light, fan).
  • Wireless Wall Panel Switch: A remote control switch that sends wireless signals to the receiver. Available in 1, 2, or 3 gang configurations.

3.2 Features

  • Wireless control for lights, fans, and other appliances.
  • Supports 2-way control configurations.
  • Remote control distance of up to 50 meters (theoretical distance) in open space.
  • Timer function for automatic light turn-off after a set duration.
  • Easy pairing and clearing of signals.
  • Compact, mini design for discreet installation.
1 Receiver + 1 Wall Panel

Figure 2: Example of a 1 Receiver + 1 Wall Panel configuration.

4. Specifications

4.1 Relay Receiver Board Parameters

Attribute Value
Working Voltage AC 85V~250V
Max Current 10A
Max Load 2400W
RF Frequency 433MHz (433.92MHZ)
Working Temperature -30~+80 degrees Celsius
Receiving Sensitivity >-97dbm
Amount of Storage Remote Controls About 20 pieces
Support Encoding 1527 Leaning code
RF Operating Mode ASK superheterodyne wireless reception
Receiving Range Up to 150 meters (theoretical distance in open space)
Dimensions 39*32*17mm
Weight 35g

4.2 Black Wall Panel Transmitter Parameters

Attribute Value
Dimensions 86*86*13 mm
Battery 1 Pcs 27A 12V battery (included)
Receiving Range Up to 50 meters (theoretical distance)
Code 1527 learning
Material Plastic (PVC)

The wall panel switch can be easily pasted on surfaces like refrigerators or other iron products.

5. Setup and Wiring

Before proceeding, ensure the main power supply is OFF. Incorrect wiring can cause damage or injury.

5.1 Wiring Diagram

The input terminal and output terminal cannot be reversed. Always connect the included yellow capacitor for low-wattage lights to prevent flickering.

Wiring Diagram for Wireless Control, 1-way, and 2-way Wall Switch

Figure 3: Wiring configurations for wireless control only, wireless + 1-way wall switch, and wireless + 2-way wall switch. Note the connection points for S1, S2, L_out, L_in, N_in, N_out.

  • Wireless control only: Connect the receiver directly to the light circuit.
  • Wireless + 1-way wall switch: Integrate the receiver with an existing 1-way wall switch.
  • Wireless + 2-way wall switch: Integrate the receiver with an existing 2-way wall switch for multi-location control.

5.2 Compatibility

The receiver is compatible with standard rocker switches and various plug types (EU, US, FR, UK). It is NOT compatible with momentary rocker switches or touch-type wall switches.

Switch and Plug Compatibility

Figure 4: Compatible rocker switches and plug types (checked green) vs. incompatible momentary and touch-type switches (red X).

6. Operation

6.1 Basic Control

Once the receiver and wall panel switch are paired (see Section 7), you can control your connected appliance by pressing the button on the wall panel switch. The signal can reach up to 50 meters (theoretical distance) in open areas.

Remote Control from Different Locations

Figure 5: Illustrates controlling lights from different locations using the remote wall panel switch.

50m Remote Distance

Figure 6: Demonstrates the effective remote control distance of 50 meters.

6.2 Timing Function (Delay Light Off Mode)

This feature allows the connected light to automatically turn off after a set period (5, 10, or 15 minutes) after being turned on via the wall panel switch.

  • To Set Up: Press and hold the wall panel switch button until the light flashes a specific number of times:
    • Flash 1 time: Sets auto-off after 5 minutes.
    • Flash 3 times: Sets auto-off after 10 minutes.
    • Flash 6 times: Sets auto-off after 15 minutes.
Timer Function Diagram

Figure 7: Visual representation of the timer function for automatic light turn-off.

7. Pairing Method

Signal pairing is required before use. Follow these steps to pair your wall panel switch with the relay receiver:

  1. Power On: Ensure the receiver is powered on.
  2. Press Learning Button: Press the learning button on the receiver 2 times.
  3. Activate Wall Panel: Press any button on the wireless wall panel switch once.
  4. Success: The pairing is successful.
Pairing and Reset Method

Figure 8: Step-by-step diagram for pairing the wall panel switch with the receiver.

8. Clearing Signals (Reset)

To clear all paired signals from the receiver, effectively resetting it:

  1. Press Learning Button 8 Times: Press the learning button on the receiver 8 times.
  2. Success: All existing data will be deleted, and the receiver is reset.

Refer to Figure 8 for a visual guide on the reset process.

9. Troubleshooting

  • Device not responding after wiring:
    • Ensure the main power supply is ON after wiring.
    • Verify that the input and output terminals are not reversed.
    • Check all wire connections for secure contact.
    • Confirm that the wall panel switch is paired with the receiver (see Section 7).
  • Low-wattage lights flicker or turn on/off automatically:
    • Connect the included yellow capacitor as shown in the wiring diagram (Figure 3). This helps stabilize the circuit for low-power loads.
  • Poor signal reception or limited range:
    • Slightly stretch the antenna on the receiver for better signal reception.
    • Ensure there are no large metal objects, electronic devices, or strong electromagnetic fields between the wall panel switch and the receiver.
    • The theoretical distance of 50m (for wall panel) and 150m (for receiver) is for open space; obstacles like walls will reduce the range.
  • Wall panel switch not working:
    • Check if the 27A 12V battery in the wall panel switch needs replacement.
    • Ensure the wall panel switch is not a momentary rocker or touch-type switch, as these are incompatible.

10. User Tips

  • Convenient Placement: The wall panel switch can be easily pasted on various surfaces, including refrigerators or other iron products, allowing for flexible placement without needing to run new wires.
  • Accessibility: This wireless system is particularly useful for providing remote control for individuals with mobility challenges, such as the elderly, children, or disabled persons, allowing them to control lights or fans from their bed or wheelchair.
  • Multi-Location Control: Utilize the 2-way control feature to manage a single light from multiple wall panel switches, ideal for stairwells or long hallways.
  • Energy Saving: Use the timing function to automatically turn off lights in areas like bathrooms or storage rooms, preventing unnecessary energy consumption.

11. Warranty and Support

This product comes with a 1-year warranty from the date of purchase. For technical support, inquiries, or warranty claims, please contact the manufacturer:

  • Manufacturer: Huizhou Wenqiao Electronic Technology Co., Ltd.
  • Address: Room 03, 12th Floor, Building 119, East Coast Garden, Fangzhilonghuwan, No. 27, Sanhuan South Road, Huicheng District, Huizhou City, Guangdong Province, China 516001
  • WhatsApp: +86 181 3880 5271 / +86-135 0227 8583
  • Email: dieseelectronic@163.com

For additional information, you may refer to the official user manual PDF: View User Manual (PDF)

The product has passed CE, FCC, and RoHS certifications, ensuring compliance with relevant safety and environmental standards.

CE FCC RoHS Certifications

Figure 9: Product certifications including CE, FCC, and RoHS.

12. Frequently Asked Questions (FAQ)

Q: Can I use this switch with my existing wall switch?

A: Yes, the relay receiver can be integrated with existing 1-way or 2-way rocker wall switches. Please refer to the wiring diagrams in Section 5.2 for proper installation. It is not compatible with momentary or touch-type switches.

Q: What should I do if my low-wattage LED light flickers?

A: For low-wattage lights, it is recommended to connect the included yellow capacitor across the load terminals as shown in the wiring diagram (Figure 3). This helps to stabilize the circuit and prevent flickering.

Q: How far can the remote control work?

A: The wall panel switch has a theoretical remote distance of up to 50 meters in open space. The receiver itself has a receiving range of up to 150 meters in open space. Actual range may vary depending on obstacles and interference.

Q: How do I reset the receiver?

A: To clear all paired signals and reset the receiver, press the learning button on the receiver 8 times. All previously stored data will be deleted.

© 2024 Tedeligo. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.