Product Overview
The ICCSSI B208APRO is a smart fingerprint door lock designed for enhanced home security and convenience. It offers multiple unlocking methods and integrates with the Tuya Smart platform for remote management.
Key Features:
- Multiple Unlocking Methods: Fingerprint, IC Card, Password, Mechanical Key, and APP (Bluetooth).
- Fast Recognition: 99.9% recognition rate with an unlock speed of less than 0.5 seconds.
- Smart Home Integration: Compatible with Tuya Smart APP for remote control and management.
- Emergency Power: Type-C interface for emergency power supply.
- Durable Material: Constructed from Aluminium alloy.
- Easy Installation: Designed for drilling installation, suitable for various door types.
Package Contents
Before installation, please ensure all components are present:
- Smart Lock (Exterior and Interior Levers) x 1
- Lock Body x 1
- Strike Box x 1
- Strike Plate x 1
- Spindle x 1
- Screw Pack (various screws) x 1
- Keys x 2
- IC Cards x 2
- 4 'AAA' batteries (Not included)
Note: Do not use an electric screwdriver during installation.
Installation Guide
1. Check the Door's Dimensions
- Measure to confirm that the door thickness is between 35mm and 54mm.
- Measure to confirm that the hole in the door is 54mm.
- Measure to confirm that the hole in the door edge is 25mm.
2. Install Latch & Strike Plate
- Install the strike box and plate with Screw A into the door frame.
- Press the square-shaped hole to pull the latch and set the latch backset to 60mm or 70mm to fit your door hole. Then install the latch into the door and tighten Screw A to fix the latch. Ensure the bevel of the latch is aimed at the bevel of the strike plate.
3. Install Exterior Lever
- Thread the wire through the spindle.
- Insert the spindle through the square-shaped (center) hole in the latch and ensure the standoffs go through the circular holes in the latch. Keep the exterior lever perpendicular to the door edge during this step.
4. Install Interior Lever
- Thread the wire through the interior lever as shown in the diagram.
- Align the standoffs to insert 2 pcs Screw B and tighten them to secure the interior lever by screwdriver.
5. Install Batteries
- Load 4 'AAA' batteries into the battery compartment, observing correct positive and negative pole orientation.
- Connect the wire male plug to the female socket.
- Install Screw C and tighten it to secure the battery compartment.
Warning: Do not use lithium batteries or rechargeable batteries that are not rechargeable.
Operating Instructions
Unlocking Methods
- Fingerprint Unlock: Place your registered finger on the fingerprint reader. The lock will unlock in less than 0.5 seconds with a 99.9% recognition rate.
- Password Unlock: Enter your registered password on the keypad. The large buttons are designed to reduce errors. The lock supports up to 100 passwords.
- IC Card Unlock: Tap your registered IC card on the designated area of the lock. The smart lock can store up to 100 IC cards.
- Mechanical Key Unlock: In case of battery depletion or other emergencies, insert the mechanical key into the keyhole and turn it 120° to unlock.
- APP Bluetooth Unlocking: Use the Tuya Smart APP to unlock the door via Bluetooth. Hold and drag the unlock icon in the app to unlock.
APP Features and Management
Download the "Smart Life" or "Tuya Smart" APP from Google Play or Apple Store.
Register Your Account:
Register or log in to your account within the app.
Pairing the Lock:
- Enable phone Bluetooth and Wi-Fi or Mobile Network (within 3 meters of the lock).
- Tap "Add device" in the app and touch the fingerprint screen or keypad to activate the lock for automatic search.
- Once successfully connected, you can rename the lock or click "Done".
Member Management:
In the app, select "Member Management" to add, share, or cancel members (common members or administrators).
Fingerprint Input:
Keep your fingers and the sensing area clean and dry. For improved recognition, especially for elderly, children, or those with light fingerprints, create multiple fingerprint files from different angles.
Note: Your fingerprints are stored only in the device for privacy.
Code Input:
Tap "Add code" and enter a 6-10 digit password, then set a code name.
- Password Privacy: The app will not display your password after it's set.
- Always end password entries with "#" for correct input.
- If you make a mistake, tap "#" and re-enter.
Temporary Codes:
- Custom Code: Follow app instructions to create custom codes.
- Time-Limited Code: Must be used at least once within 24 hours of activation, otherwise it becomes invalid. Cannot be modified or renamed.
- One-Time Code: Valid for 6 hours and can only be used once.
- Dynamic Code: Valid for 5 minutes and can be used multiple times before expiration.
Always enter a random key to wake up the keypad before entering any code.
More Settings:
You can turn on/off Remote Unlock and adjust the Lock Volume (Mute or Normal) via the app. Remote unlocking requires a gateway connection.
Maintenance
Battery Replacement
The lock will indicate low power by beeping once and flashing a red light for 10 seconds after a successful unlock (fingerprint or app). This signals that it's time to replace the 4 'AAA' batteries.
Cleaning
To ensure optimal performance of the fingerprint reader, always keep your fingers and the sensing area clean and dry.
Factory Reset
To restore the lock to factory settings, press and hold the RESET button for a few seconds. After resetting, all registered fingerprints will be deleted, and any fingerprint can unlock the lock until new users are added via the Smart Life App.
Troubleshooting
- Low Power: If the lock indicates low power, replace the 'AAA' batteries. In an emergency, use a power bank connected to the Type-C interface for temporary power.
- Unable to Unlock (Battery Dead): If the battery runs out and you are locked out, use the mechanical key to open the door. It is recommended to keep a mechanical key accessible outside the house (e.g., in your car or office) for emergencies.
- Unlocking Failure: If unlocking fails, the lock will beep once and blink red. Re-attempt the unlock method. For fingerprint, ensure your finger is clean and dry and try different angles.
- Password Entry Error: If you make a mistake while entering your password, tap '#' and re-enter the correct password.
FCC Warning
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Specifications
| Attribute | Value |
|---|---|
| Brand Name | ICCSSI |
| Model Number | B208APRO |
| Material | Aluminium alloy |
| Installation Method | Drilling installation |
| Suitable Door Type | Steel Door, Wooden Door, Brass Door, Stainless Steel Door, Other |
| Ways To Unlock | App, Remote Control, Bluetooth, Mechanical Keys, Card, Password, FINGERPRINT |
| Doorknob Function | Biometric, Key & Keypad |
| Connectivity | Bluetooth |
| Smart Home Platform | Tuya |
| Power Supply | DRY BATTERY (4*AAA, not included) |
| Voltage Range | 4.6-6.5V |
| Standby Current | < 90μA |
| Working Current | < 500mA |
| Working Temperature | 23°F-131°F (-5°C-55°C) |
| Low Power Warning | 4.8±0.2V |
| Fingerprint Capacity | 50 PCS |
| Password Capacity | 100 PCS |
| Card Capacity | 100 PCS |
| Handle Direction | Direction Reversible |
| Certifications | CE, FCC, RoHS |
| Package Dimensions (L x W x H) | 20cm x 10cm x 13cm |
| Package Weight | 1.0 kg |
User Tips
- For optimal fingerprint recognition, always ensure your finger and the sensor are clean and dry.
- If you experience inconsistent fingerprint recognition, try registering your fingerprint multiple times from different angles to improve accuracy.
- Always keep a mechanical key in a safe, accessible location outside your home (e.g., in your car or at a trusted neighbor's) in case of battery failure or other emergencies.
- When entering passwords, remember to press '#' after the sequence to confirm.
- For temporary access, utilize the various temporary code options available through the Tuya Smart app.
Warranty and Support
For detailed warranty information and customer support, please refer to the official user manual PDF provided by the manufacturer. You can access the PDF here: ICCSSI B208APRO User Manual (PDF).
If you encounter any issues not covered in this manual or the PDF, please contact the seller or manufacturer directly for assistance.
Frequently Asked Questions (FAQ)
- Q: How do I reset the lock to factory settings?
- A: Press and hold the RESET button on the interior lever for a few seconds. All registered fingerprints and settings will be cleared.
- Q: What should I do if the battery dies and I can't unlock the door?
- A: You have two options: use the mechanical key provided, or connect a power bank to the Type-C emergency power supply port on the exterior lever to temporarily power the lock.
- Q: How many fingerprints, passwords, and IC cards can be registered?
- A: The lock supports up to 50 fingerprints, 100 passwords, and 100 IC cards.
- Q: Is the lock waterproof?
- A: The product specifications do not explicitly state a waterproof rating. It is generally recommended for indoor use or protected outdoor areas.
- Q: Can I control the lock remotely when I'm away from home?
- A: Yes, if you have a compatible Tuya gateway connected, you can control the lock remotely via the Tuya Smart APP. Without a gateway, control is limited to Bluetooth range.