1. Introduction
This manual provides essential information for the safe and effective operation of your SLyric 10D Emerald Laser Weight Loss Machine. This device utilizes 532nm green laser light for body slimming, shaping, and skin tightening. Please read this manual thoroughly before initial use and keep it for future reference.

Figure 1: SLyric 10D Emerald Laser Slimming Device. Key benefits include fat dissolution, cellulite reduction, collagen rebuilding, and improved metabolism.
2. Safety Information
Always follow basic safety precautions when using electrical appliances, especially those involving laser technology. This device is intended for professional use or under professional guidance. Do not operate if you are pregnant, have skin conditions, or other medical contraindications. Always wear protective eyewear during operation. Keep out of reach of children.
3. Setup
3.1 Unpacking and Inspection
Carefully unpack all components from the shipping container. Verify that all parts are present and undamaged. The main unit is shipped in a protective flight case.

Figure 2: Device components as received in packaging.
3.2 Placement
Place the device on a stable, level surface in a treatment room. Ensure adequate space around the unit for operation and patient access. The device is equipped with wheels for easy maneuverability.
3.3 Power Connection
Connect the power cable to the device and then to a grounded electrical outlet. Ensure the power supply matches the device requirements:
- Voltage: AC110V~220V±10%
- Frequency: 50-60Hz
3.4 Initial Power-On
Turn on the main power switch, usually located at the rear or base of the unit. The touch screen display will illuminate, indicating the device is ready for operation.

Figure 3: Front view of the device with the touch screen and active laser heads.
4. Operating Instructions
4.1 Principle of Action
The 10D Emerald Laser works by irradiating fat cells with specific green light wavelengths (532nm). This causes fat droplets to leak out from the fat cell membrane. These released fat cells are then disintegrated and excreted through the body's natural lymphatic system.

Figure 4: Principle of Action diagram showing fat cell response to laser treatment.
4.2 Treatment Areas
The device is designed for use on various body parts to target localized fat and improve skin texture. Common treatment areas include:
- Abdomen
- Back
- Neck
- Thighs
- Hips
- Arms

Figure 5: Laser application on various body parts.
4.3 Operating the Touch Screen
The device features a main Host Touch Screen (10.4 inches) and a Laser Touch Screen (7 inches) for controlling treatment parameters. Navigate through the menus to select desired settings.
4.4 Adjusting Treatment Parameters
The following parameters can be adjusted via the touch screen interface:
- Energy: 1-3 gears (adjustable)
- Rotating Speed: 1-3 gears (adjustable)
- Laser Wing Angle: Adjustable up to 100 degrees to conform to body contours.
4.5 Treatment Procedure
- Ensure the patient is comfortably positioned on a treatment bed.
- Adjust the laser arm and heads to cover the target treatment area. The laser wings can be adjusted up to 100 degrees.
- Select the appropriate energy level and rotating speed based on the treatment protocol and patient comfort.
- Initiate the treatment via the touch screen.
- Monitor the patient throughout the session.
Video 1: Demonstration of the 10D Emerald Laser Machine in operation on a patient's abdomen.
5. Maintenance
5.1 Cleaning
Regularly clean the device surfaces, including the touch screens and laser heads, with a soft, damp cloth. Do not use abrasive cleaners or solvents that could damage the finish or electronic components. Ensure the device is powered off and unplugged before cleaning.
5.2 Storage
When not in use, store the device in a clean, dry environment, away from direct sunlight and extreme temperatures. Use the provided flight case for long-term storage or transportation to protect the unit.
6. Troubleshooting
If you encounter any issues with your device, please refer to the following basic troubleshooting steps:
- Device not powering on: Check the power cable connection and ensure the main power switch is in the 'ON' position. Verify the power outlet is functional.
- Laser not emitting: Check the settings on the touch screen. Ensure the treatment session has been initiated correctly.
- Unusual noises or smells: Immediately power off the device and unplug it. Contact customer support for assistance.
For any persistent issues, please contact customer support.
7. Specifications

Figure 6: Detailed specifications of the device.
| Feature | Specification |
|---|---|
| Model Number | 10D Rotating Green Laser Lights |
| Host Touch Screen | 10.4 inch |
| Laser Touch Screen | 7 inch |
| Wave Length | 532nm ±10nm (Green Light) |
| Energy | 1-3 gears (adjustable) |
| Rotating Speed | 1-3 gears (adjustable) |
| Laser Single Head Power | 500mW |
| Power of Diode | 200mW |
| Treatment Area | About 30mm*800mm |
| Number of Treatment Heads | 10 pieces |
| Angle Adjustable of Laser Wings | 100 degrees |
| Fuse | 10A |
| Power Consumption | 150W |
| Voltage | AC110V~220V±10%, 50-60Hz |
| Material | Metal |
| Features | Pore Remover, Weight Loss, Face Lift, Cellulite Reduction, Skin Tightening |
| Packing Weight | 60KG |
| Package Size | 111*77*61CM |
8. User Tips
- For optimal results, adhere to recommended treatment protocols and frequency.
- Maintain a healthy lifestyle, including diet and exercise, to complement the device's effects.
9. Warranty and Support
9.1 Warranty
This device comes with a 1-Year Warranty from the date of purchase.
9.2 Support Services
Our support team is available to assist you with any questions or issues. We offer:
- 24-hour online service
- Instructional operation video training
- Free spare parts (as per warranty terms)
- Video technical support
- Online support
For a more detailed user manual, please refer to the official PDF document: Download User Manual (PDF)