1. Product Information
This manual provides instructions for the installation, operation, and maintenance of the S1000RR Motorcycle In-Tail LED Integrated Tail Light.
- Product Name: S1000RR Motorcycle In-Tail LED Integrated Tail Light
- Model Compatibility: For BMW S1000RR 2019-2022
- Manufacturer: Shenzhen Xinruitong Trading Co.Ltd
- Manufacturer Address: 601.Building 49. Hewei Village. Qingshuihe Street.: LuohnDistrict. Shenzhen City.Guangdong Province
- Manufacturer Email: zjs1772249041@outlook.com
- EU Authorized Representative: FranceEffieCosmeceuticals TechnologyCoLtd
- EU Representative Address: FR-73RUEDELAPLAINE75020PARIS.France
- EU Representative Tel: +44-7491154650
- EU Representative E-mail: info@gd-rep.com
2. Safety & Warnings
Please read all instructions carefully before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow all installation and operation guidelines to avoid injury.
- Do not expose to water or moisture.
- Handle with care to avoid cuts or injuries.
3. Features
- High power pulse-width modulated LEDs provide extremely bright light output.
- A total of 6 lamps are distributed on different axes, creating a wide cone of light and increasing visibility.
- Illuminated embellished rings provide side contour visibility.
- Plug-and-play cabling eliminates the need to cut, splice, or solder S1000RR wires.
- Bolt-on installation without modification.
- The color and texture of the lampshade are designed to match the BMW rear for a special aesthetic.
4. Setup (Installation)
The integrated LED tail light is designed for a straightforward, bolt-on, plug-and-play installation on compatible BMW S1000RR models.
- Ensure the motorcycle's power is off and the battery is disconnected before beginning installation.
- Carefully remove the existing tail light assembly from your BMW S1000RR (2019-2022 model).
- Connect the wiring harness of the new integrated LED tail light to the motorcycle's existing wiring. The plug-and-play design means no cutting or splicing is required.
- Position the new tail light unit into the designated area on the motorcycle's tail section.
- Secure the tail light unit using the appropriate bolts. Ensure it is firmly attached and stable.
- Reconnect the motorcycle's battery and test the tail light, brake light, and turn signal functions.
5. Operating Instructions
The integrated LED tail light combines multiple functions into a single unit:
- Tail Light: Provides constant red illumination when the motorcycle's lights are on, enhancing rear visibility.
- Brake Light: Activates brighter red illumination when the brakes are applied, signaling deceleration to following traffic.
- Turn Signals: Flashes amber lights on the respective side when the turn signal is activated, indicating a change in direction. The 6 lamps distributed on different axes create a wide cone of light for increased visibility.
6. Maintenance
To ensure optimal performance and longevity of your LED tail light, follow these maintenance guidelines:
- Cleaning: Regularly clean the lens with a soft, damp cloth to remove dirt and debris. Avoid abrasive cleaners or solvents that could damage the plastic.
- Inspection: Periodically check the light for any signs of damage, such as cracks in the lens or loose wiring. Ensure all bolts remain tight.
- Moisture: While designed to be weather-resistant, avoid prolonged exposure to extreme moisture or direct high-pressure water sprays.
7. Troubleshooting
If you encounter any issues with your integrated LED tail light, refer to the following troubleshooting steps:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light not illuminating | Loose connection, no power, faulty LED | Check all wiring connections, ensure power is supplied to the light, inspect for visible damage to LEDs. |
| Lights flickering | Loose wiring, unstable power supply | Secure all wiring connections. If the problem persists, consult a professional. |
| Turn signals not flashing | Incorrect wiring, faulty flasher relay (if applicable) | Verify turn signal wiring. Check or replace the flasher relay if necessary. |
8. Specifications
- Model Name: For S1000RR
- Fitment: For BMW S1000RR 2019-2022
- Quantity: A pair (left and right units)
- Available Housing Colors: Red, Black, Blue
- Light Type: LED (High power pulse-width modulated)
- Functions: Integrated Tail Light, Brake Light, Turn Signals
- Material: High Quality PC+ABS Plastic
- Origin: Mainland China
Package Dimensions & Weight:
- Length: 21 cm
- Width: 19 cm
- Height: 7 cm
- Weight: 0.32 kg
9. User Tips
- After installation, always double-check all wiring connections to ensure they are secure and properly seated.
- Verify the stability of the installed light by gently wiggling it to confirm it is firmly bolted to the motorcycle.
- For optimal light output and visibility, ensure the light is aligned correctly and not obstructed.
10. Warranty & Support
For any product-related inquiries, technical support, or warranty claims, please contact the manufacturer or the EU authorized representative using the details below:
Manufacturer Contact:
- Company: Shenzhen Xinruitong Trading Co.Ltd
- Email: zjs1772249041@outlook.com
EU Authorized Representative Contact:
- Company: FranceEffieCosmeceuticals TechnologyCoLtd
- Telephone: +44-7491154650
- E-mail: info@gd-rep.com