Introduction
This manual provides comprehensive instructions and important information for the KAVERY EA888 Aluminium Engine Oil Radiator Cooler. Please read this manual thoroughly before installation and use to ensure proper function and safety.
Safety Information
Warning!
- This product is an automotive component and should only be handled and installed by qualified personnel.
- Always ensure the engine is cool and depressurized before attempting any installation or maintenance.
- Wear appropriate personal protective equipment (PPE) such as gloves and eye protection.
- Refer to your vehicle's service manual for specific torque specifications and procedures.
- Not suitable for children under 36 months. Small parts, choking hazard.
Specifications
| Attribute | Value |
|---|---|
| Product Name | EA888 Aluminium Engine Oil Radiator Cooler |
| Brand | KAVERY |
| Model Number | 06J 117 021 M |
| Other Part Number | 06J 117 021 M |
| Interchange Part Number | 06J 117 021 M |
| Manufacturer Part Number | 06J 117 021 M |
| OEM NO. | 06J 117 021 M |
| Placement on Vehicle | Engine |
| Material | Aluminum |
| Country/Region of Manufacture | China / Mainland China |
| Package Length | 18 cm |
| Package Width | 10 cm |
| Package Height | 10 cm |
| Package Weight | 0.61 kg |
Setup and Installation
The installation of the KAVERY EA888 Aluminium Engine Oil Radiator Cooler is designed to be straightforward, as indicated by "安装简易" (easy installation) in the provided instructions. However, due to the critical nature of engine components, professional installation is highly recommended.
General Installation Steps (Consult a professional for detailed vehicle-specific instructions):
- Preparation: Ensure the vehicle's engine is completely cool. Disconnect the battery's negative terminal.
- Drain Fluids: Drain the engine oil and coolant from the system as per your vehicle's service manual.
- Access: Locate the existing oil cooler assembly on your engine. This may require removing other components for access.
- Removal: Carefully disconnect any hoses or lines attached to the old oil cooler. Remove the mounting bolts and detach the old oil cooler.
- Inspection: Inspect the mounting surface and surrounding components for any damage or debris. Clean thoroughly.
- Installation of New Cooler: Position the new KAVERY oil cooler (Model 06J 117 021 M) and secure it with the appropriate mounting bolts. Ensure all connections are properly seated and tightened to the manufacturer's specifications.
- Reconnect Lines: Reattach all oil and coolant lines, ensuring they are securely fastened and free from leaks.
- Refill Fluids: Refill the engine with the correct type and amount of engine oil and coolant.
- Bleed Air: Bleed any air from the cooling system as per your vehicle's service manual.
- Test: Reconnect the battery. Start the engine and check for any leaks. Monitor engine temperature and oil pressure.
Operation
The KAVERY EA888 Aluminium Engine Oil Radiator Cooler operates passively as part of your vehicle's engine oil and cooling systems. Once correctly installed, it continuously works to regulate the temperature of the engine oil by transferring heat to the engine's coolant. No direct user interaction is required for its operation.
Ensure your vehicle's cooling system is properly maintained and filled with the correct coolant mixture to allow the oil cooler to function efficiently.
Maintenance
Regular maintenance of your engine's cooling and lubrication systems is crucial for the longevity and performance of the oil cooler.
- Fluid Checks: Regularly check engine oil and coolant levels and top up as necessary with fluids that meet your vehicle manufacturer's specifications.
- Fluid Changes: Adhere to your vehicle's recommended service intervals for oil and coolant changes. Contaminated fluids can reduce the efficiency and lifespan of the oil cooler.
- Leak Inspection: Periodically inspect the oil cooler and its connections for any signs of leaks (oil or coolant). Address any leaks immediately to prevent engine damage.
- External Cleaning: If accessible, gently clean any external debris (e.g., dirt, leaves) from the oil cooler fins to ensure optimal heat dissipation. Use compressed air or a soft brush.
- System Flush: Consider a cooling system flush at recommended intervals to prevent buildup and maintain optimal heat exchange.
Troubleshooting
If you suspect an issue with your engine oil cooler, consider the following common problems and potential solutions:
- Oil Leaks:
- Symptom: Visible oil drips or stains around the oil cooler or on the ground.
- Possible Cause: Loose connections, damaged gaskets/O-rings, or a cracked cooler housing.
- Solution: Check and tighten connections. Replace worn or damaged gaskets/O-rings. If the housing is cracked, the oil cooler needs replacement.
- Coolant Leaks:
- Symptom: Visible coolant drips or stains, or a drop in coolant level.
- Possible Cause: Loose coolant lines, damaged gaskets/O-rings, or internal cooler failure.
- Solution: Check and tighten coolant lines. Replace gaskets/O-rings. If coolant is mixing with oil (see below), the cooler is likely faulty.
- Oil and Coolant Mixing (Cross-Contamination):
- Symptom: Milky substance in the oil (on dipstick or oil cap), or oil in the coolant reservoir.
- Possible Cause: Internal failure of the oil cooler, allowing oil and coolant to mix.
- Solution: This indicates a severe internal leak within the oil cooler. The unit must be replaced immediately to prevent significant engine damage.
- Engine Overheating / High Oil Temperature:
- Symptom: Engine temperature gauge reads high, or oil temperature warning light illuminates.
- Possible Cause: Clogged oil cooler fins, restricted oil/coolant flow, or a faulty thermostat.
- Solution: Inspect and clean cooler fins. Check for blockages in oil and coolant lines. Ensure the cooling system is functioning correctly (e.g., water pump, thermostat).
For persistent issues or if you are unsure about diagnosing a problem, it is always best to consult a certified automotive technician.
User Tips
- Verify Part Number: Always double-check the OEM part number (06J 117 021 M) against your vehicle's existing part or service manual to ensure compatibility before purchase and installation.
- Professional Installation: While described as "easy installation," the critical role of this component in engine health means professional installation is highly recommended to avoid errors and ensure proper sealing.
- Gasket Replacement: Always use new gaskets and O-rings when installing a new oil cooler to ensure a leak-free seal.
- Fluid Quality: Use high-quality engine oil and coolant that meet or exceed your vehicle manufacturer's specifications to maximize the life and efficiency of the oil cooler.
Warranty and Support
The manufacturer offers a 2-year or 40,000 kilometers guarantee for AUDI VW PORSCHE parts, which applies to this product. For specific warranty claims or technical support, please contact the seller or manufacturer directly with your purchase details.
A user manual in PDF format is available for download at this link. This document contains additional information and can be referenced for further details.
For any questions or assistance, please refer to the contact information provided by your retailer or the manufacturer.