1. Introduction
The LAUNCH CRP129 HD is an all-in-one diagnostic tool designed for heavy-duty trucks, pickups, buses, trailers, tractors, dumpers, and agricultural and construction vehicles. It supports full system diagnosis for 24V trucks and also functions as a 12V code reader for cars with full OBD2 capabilities. This global version device offers extensive vehicle coverage, supporting 99% of vehicles from over 50 global brands and 10,000 truck models, including 10 types of truck engines (e.g., Cummins, Caterpillar, Hino).
Key features include:
- Full System Diagnosis: Accesses and diagnoses all electronic control systems.
- Auto VIN & Auto Scan (2006+): Automatically identifies vehicles and performs intelligent system scanning.
- 7+ Special Functions: DPF regeneration, oil reset, speed limit adjustment, ABS bleeding, injector coding, cylinder deactivation compression, advanced ECM data, reset ABS controller, set parameters, and more.
- Intuitive Data Analysis: Features 4-in-1 live data graphing, data stream recording and playback, and diagnostic report sharing and printing.
- Online Feedback & Remote Diagnosis: Allows users to share problems for support and enables remote assistance.
- View History: Provides quick access to previously tested vehicles and diagnostic records.
- Maintenance Help: Includes how-to videos, operation skills, user manual, Q&A, and quick start guide.
The device is equipped with multiple interfaces including OBD-16 Pin, 6-Pin OBD, 9-Pin OBD, and Type II 9-PIN OBD Diagnostic Connectors, supporting J1939, J1708, J1587, and J27145 protocols. It also performs routine diagnosis for almost all cars, mini-vans, and light-duty vehicles from 1996 onwards using various ISO and SAE protocols.
2. Safety Precautions and Warnings
To prevent personal injury or damage to vehicles and/or the tool, please read this user's manual carefully and observe the following safety precautions at a minimum whenever working on a vehicle:
- Battery Warning: This tool contains an internal Lithium Polymer battery. The battery can burst or explode, releasing hazardous chemicals. To reduce the risk of fire or burns, do not disassemble, crush, pierce, or dispose of the battery in fire or water.
- Not a Toy: This product is not a toy. Do not allow children to play with or near this item.
- Environmental Conditions: Do not expose the device to rain or wet conditions. Do not place the device on any unstable surface.
- Charging Safety: Never leave the device unattended during the charging process. The device must be placed on a non-flammable surface during charging.
- Handling: Handle the device with care. If the device is dropped, check for breakage and any other conditions that may affect its operation.
- Explosive Atmospheres: Do not operate the tool in explosive atmospheres, such as in the presence of flammable liquids, gases, or heavy dust.
- Maintenance: Keep the tool dry, clean, free from oil, water, or grease. Use a mild detergent on a clean cloth to clean the outside of the device when necessary.
- Pacemakers: People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemakers could cause interference or failure.
- Automotive Testing Environment: Always perform automotive testing in a safe environment.
- Driving Safety: Do not attempt to operate or observe the tool while driving a vehicle. Operating or observing the tool will cause driver distraction and could cause a fatal accident.
- Eye Protection: Wear safety eye protection that meets ANSI standards.
- Engine Safety: Keep clothing, hair, hands, tools, test equipment, etc., away from all moving or hot engine parts.
- Ventilation: Operate the vehicle in a well-ventilated work area; exhaust gases are poisonous.
- Vehicle Stability: Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests.
- Ignition System: Use extreme caution when working around the ignition coil, distributor cap, ignition wires, and spark plugs. These components create hazardous voltages when the engine is running.
- Transmission and Brake: Put the transmission in P (for A/T) or N (for M/T) and make sure the parking brake is engaged.
- Fire Safety: Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
- Connecting/Disconnecting Equipment: Don't connect or disconnect any test equipment while the ignition is on or the engine is running.
3. Components and Controls
The LAUNCH CRP129 HD diagnostic tool features a robust design with a clear touch screen and intuitive controls.


Main Components:
- Charging Port: Used to charge the tool.
- DB-15 Diagnostic Connector: Connects to the vehicle's Data Link Connector (DLC) port.
- Power Button: Turns the tool on/off.
- Touch Screen: Displays test results and user interface.
- HOME Button: Navigates to the Job Menu screen.
- SELECT Button: Used for selection in menus.
- OK Button: Confirms selections.
- BACK Button: Returns to the previous menu.

4. Setup
4.1 Charging
There are two methods available for charging your LAUNCH CRP129 HD:
- Via Diagnostic Cable: Insert the diagnostic cable into the vehicle's DLC port.
- Via Data Cable: Plug one end of a data cable (not included) into the charging port of the tool, and the other end to a PC.
When the tool is powered on, the screen will automatically light up.
Note: Attempting to charge the tool via the OBD diagnostic port will consume the vehicle's battery power. It is not recommended to charge the tool in this way except for OBD diagnosis operations.
4.2 Getting Started
If this is your first time using the tool, you need to make some system settings:
- Power on the tool. The screen displays a welcome page. Tap "Start" to proceed.
- Choose the desired system language, and tap "Next".
- Choose the desired time zone, and tap "Next" to enter the WLAN setup screen.
- Slide the Wi-Fi switch to ON. The system will start searching for available wireless LANs. Choose the desired WLAN access point/network.
- If the network you chose is open, you can connect directly.
- If the selected network is encrypted, you have to enter the correct security key (network password).
- After the network connection is done, tap "Next Step" to configure workshop information. Input the required information, and tap "Next Step" to proceed.
- Carefully read all terms and conditions of the user agreement, check the box before "Agree to all the above terms", and tap "OK" to finish the sign-up process and navigate to the Job Menu.
Note: If you choose "Ignore" in WLAN setup, it will go into the date setting page. If the tool has been properly connected to the Internet, the system will automatically obtain the correct network date and time and navigate to step 5.
Note: It is strongly recommended to fill in a valid email address. After you configure this option, the system will append it to the report every time a report is successfully generated.
4.3 Job Menu Overview
The main menu screen includes the following function modules:
| Module | Description |
|---|---|
| Diagnose | Configures the tool to operate as a professional diagnostic device. |
| HD OBD | Provides a quick way to check for DTCs, isolate the cause of the Malfunction Indicator Lamp (MIL), check monitor status prior to emissions certification testing, verify repairs, and perform other emission-related services. |
| Upgrade | Updates vehicle diagnostic software and APK. Requires a stable network connection. |
| Reset | Offers coding, reset, relearn, and other service functions to restore vehicles to functional status after repair or replacement. |
| Settings | Manages data and system settings, including Network setup, Workshop information, and Brightness. |

5. Operation
5.1 Connection
- Turn the ignition off.
- Locate the vehicle's Data Link Connector (DLC) port. The DLC is normally located in the driver's cab (refer to the vehicle's owner's manual for its exact location).

Connecting the LAUNCH CRP129 HD diagnostic tool to a vehicle's OBD-II port. - Plug the diagnostic cable into the DB-15 diagnostic connector on the tool, and then tighten the captive screws.
- Select the appropriate heavy-duty vehicle adapter for the vehicle's DLC type.
- For standard OBD II DLC, plug the diagnostic cable into the vehicle's DLC port, and then tighten the captive screws.
- For non-standard OBD II DLC, connect one end of the adapter to the diagnostic cable, and the other end to the vehicle's DLC port.
- Turn the ignition on. The engine can be off or running.
Note: The adapter is keyed and will only fit one way. If you have problems connecting the adapter to the DLC, rotate the connector 180° and try again.
Caution: Don't connect or disconnect any test equipment with the ignition on or engine running.
5.2 System Diagnostics
This function is designed to diagnose electronic control systems of a single vehicle model.
Notes:
- All software is updated periodically. It is recommended to update and install the latest software version for the best service, functions, and experience.
- Use and update of the diagnostic software pre-installed on the tool is free of charge for 2 years. If it expires, it will be disabled. In this case, the user needs to renew the subscription via a specific Subscription Renewal Card.
5.2.1 Automatic System Scan
This function allows quick access to the electronic control systems of the vehicle by decoding the VIN, without manual step-by-step menu selection. After connection, turn the ignition key on, and the system enters auto-detect mode.
Note:
- Make sure the "Automatic detection on connect" in "Settings" is set to ON.
- A highly stable and solid network connection is recommended for successful VIN access.
A. Once the system successfully obtains the VIN (Vehicle Identification Number) information of the currently identified vehicle, it will continue scanning the vehicle systems. After the scanning is complete, it will automatically enter the system selection screen.

User can tap the desired system to start diagnosis.
B. If the tool fails to access the VIN information, it will automatically enter the scan mode selection screen. Tap "Manually select" to enter the Manual Diagnosis mode. Refer to Chapter 4.2.2 for details in the full user manual.
5.2.2 Manual Diagnosis
If the tool cannot decode the VIN information, you can also perform vehicle diagnosis manually by executing menu-driven commands step by step.
Notes:
- Before diagnosing, please make sure the corresponding vehicle manufacturer software has been installed in your tool.
- The diagnostic menu may vary by the vehicle's make, model, and year.
Refer to the flowchart below to diagnose a vehicle manually:

A. Version Information
This option can read the version information of the system mode, vehicle VIN, software, and ECU.
B. Read Fault Code
This function displays detailed information about DTC records retrieved from the vehicle's control system. Tap "Read Fault Code" on the test function selection screen; the screen will display the diagnostic result.
Note: Retrieving and using DTCs for troubleshooting vehicle operation is only one part of an overall diagnostic strategy. Never replace a part based only on the DTC definition. Each DTC has a set of testing procedures, instructions, and flowcharts that must be followed to confirm the cause of the problem. Refer to the vehicle's service manual for detailed testing instructions.


On-screen Buttons:
- Back: Tap to return to the previous screen.
- Search: Tap to search for more information about the current DTC online.
- Report: To save the current data in text format. All diagnostic reports can be accessed from Settings -> Data -> Diagnostic Report.
C. Clear Fault Code
After reading the retrieved codes from the vehicle and performing certain repairs, you can use this function to erase the codes from the vehicle. Before performing this function, please ensure the vehicle's ignition key is in the ON position with the engine off.
Notes:
- If you plan to take the vehicle to a Service Center for repair, DO NOT erase the codes from the vehicle's computer. If data is erased, valuable information that might help the technician troubleshoot the problem will also be erased.
- Clearing DTCs does not fix the problem(s) that caused the code(s) to be set. If proper repairs to correct the problem that caused the code(s) to be set are not made, the code(s) will appear again, and the check engine light will illuminate as soon as the problem that caused the DTC to be set manifests itself.
D. Read Data Stream
This option retrieves and displays live data and parameters from the vehicle's ECU.

After selecting the desired items, tap "OK" to enter the data stream reading page.

On-screen Buttons:
- Combine: Tap to merge values in waveform for easier comparisons. A maximum of 4 items can be selected at the same time.
- Report: To save the current data in text format. All diagnostic reports can be accessed from Settings -> Data -> Diagnostic Report.
- Record: To save the current data in text format. All diagnostic reports can be accessed from Settings -> Data -> Diagnostic Record.
5.3 OBD Diagnosis

5.3.1 HD OBD
This option allows you to diagnose the electronic control systems of heavy-duty vehicles supporting J1939 and J1708 protocols.
HD Protocols: SAE J1708, SAE J1587, and SAE J1939 are automotive diagnostic protocol standards developed by the Society of Automotive Engineers (SAE).
- SAE J1708: Defines the physical layer for serial communications between ECUs on heavy-duty vehicles. Common higher-layer protocols operating on J1708 are SAE J1587 and SAE J1922.
- SAE J1587: Used for heavy-duty and most medium-duty vehicles built after 1985. J1587 protocol uses different diagnostic connectors; 6-pin Deutsch-connector was standard from 1996-2001, then OEMs converted to 9-pin Deutsch in 2001. Some OEMs still use 6-pin Deutsch.
- SAE J1939: Considered a replacement for SAE J1708 and SAE J1587 specifications. It is a vehicle bus standard for communication and diagnostics among vehicle components in the automotive and Heavy Duty Vehicle industry. Widely adopted by diesel engine manufacturers for various diesel-powered applications.
DTCs for J1587/J1708 and J1939:
- (SID) Subsystem Identifier: Indicates what function on the ECU has failed.
- (FMI) Failure Mode Indicator: Indicates in what way the function failed.
- (OC) Occurrence: Indicates the occurrence times of fault codes.
- (SPN) Suspect Parameter Number: Indicates what function on the ECU has failed (for J1939).
1. After the tool is properly connected to the vehicle's DLC, tap "HD OBD" to enter the following screen.

Tap "System Automatic Search" to scan which systems are equipped on the test vehicle automatically.
Tap "System Manual Selection" to manually select the desired system to proceed.
2. Select the test system to enter the following screen.

Note: The diagnostic menu may vary by the vehicle's make, model, and year.
3. All diagnostic functions are similar to those on system diagnostics. No further descriptions will be given for it. Please refer to Chapter 4.2.2 for detailed operations in the full user manual.
5.3.2 EOBD II
This option provides a quick way to check for DTCs, isolate the cause of the illuminated Malfunction Indicator Lamp (MIL), check monitor status prior to emissions certification testing, verify repairs, and perform other emission-related services.
After the tool is properly connected to the vehicle's DLC, tap "EOBD II". The tool will automatically start a check of the vehicle's computer to determine which type of communication protocol it is using. When the tool identifies the computer's communication protocol, a communication link is established, and the screen will display the Monitor Status.

Tap "OK" to enter the diagnostic test modes selection screen. It mainly includes the following functions:
- Read Codes: Identifies which section of the emission control system has malfunctioned.
- Erase Codes: Erases codes from the vehicle after retrieving them and performing repairs. Ensure the vehicle's ignition key is in the ON position with the engine off before operation.
- I/M Readiness: Checks whether the various emissions-related systems on the vehicle are operating properly and are ready for Inspection and Maintenance testing. It can also be used to check the Monitor Run Status and confirm if a car fault repair has been performed correctly.
- Data Stream: Retrieves and displays live data and parameters from the vehicle's ECU.
- View Freeze Frame: Takes a snapshot of operating conditions when an emission-related fault occurs. Note: If DTCs were erased, Freeze Data may not be stored in vehicle memory depending on the vehicle's make, model, and year.
- O2 Sensor Test: Retrieves O2 sensor monitor test results of the most recently completed tests from the vehicle's on-board computer.
- On-board Monitor Test: Retrieves test results for emission-related powertrain components and systems that are not continuously monitored. Availability is determined by the vehicle manufacturer.
- EVAP System Test: Initiates a leak test for the vehicle's EVAP system. Refer to the vehicle's service repair manual for procedures to stop the test.
- Vehicle Info: Retrieves information (provided by the vehicle manufacturer) from the vehicle's on-board computer, including VIN (Vehicle Identification Number), CID (Calibration ID), and CVN (Calibration Verification Number).
5.4 History
The History function provides direct access to previously tested vehicles. Users can resume from the last operation without starting from scratch. Tap "History" on the Diagnose main menu screen, and all diagnostic records will be listed in date sequence.
6. Maintenance
6.1 Reset Functions
The tool offers coding, reset, relearn, and other service functions to help vehicles return to functional status after repair or replacement. Available tests vary by vehicle manufacturer, year, and model. Due to continuous improvements, available service functions are subject to change without prior written notice. It is recommended to check for updates regularly.
There are two methods to reset the service lamp: Manual Reset or Auto Reset. Auto Reset sends commands from the tool to the vehicle's ECU for resetting. Manual Reset requires users to follow on-screen instructions to select options, enter data, and perform necessary actions, with the system guiding through the process.
6.1.1 DPF Regeneration
This function helps remove PM (Particulate Matters) from the DPF filter using combustion oxidation methods (e.g., high-temperature heating, fuel additive, or catalyst to reduce PM ignition combustion) to maintain filter performance. It needs to be performed in the following cases:
- The exhaust back pressure sensor is replaced.
- The PM trap is removed or replaced.
- The fuel additive nozzle is removed or replaced.
- The catalytic oxidizer is removed or replaced.
- The DPF regeneration MIL is on and maintenance is performed.
- The DPF regeneration control module is replaced.
Types of DPF Regeneration:
- Passive Regen: Occurs when driving for an extended period (20-30 minutes) at high speeds, causing exhaust temperatures to rise sufficiently to burn off soot particles trapped by the DPF.
- Active Regen: Activated when the soot collected in the DPF reaches a certain level (typically 45% of total capacity). This triggers post-combustion fuel injection, increasing exhaust temperature to burn off soot even at lower speeds.
6.1.2 Urea Drive (DEF)
This function can drive the urea pump to perform reverse pumping, compression, injection, and other operations through the diagnostic scanner. It needs to be performed after urea pump maintenance.
6.1.3 Maintenance Reset (Oil Service Reset)
This function resets the oil service for the engine oil life system, which calculates an optimal oil life change interval based on vehicle driving conditions and weather. It needs to be performed in the following cases:
- If the service lamp is on, run car diagnostics first for troubleshooting. Afterward, reset the driving mileage or driving time to turn off the service lamp and enable a new driving cycle.
- If the service lamp is not on, but you have changed the engine oil or electric appliances that monitor oil life, you need to reset the service lamp.
6.1.4 Injector Coding
This function writes the injector's actual code or rewrites the code in the ECU to the injector code of the corresponding cylinder, ensuring accurate cylinder injection quantity. It needs to be performed after the ECU or injector is replaced.
6.1.5 Speed Limit Reset
This function allows you to adjust or cancel the maximum vehicle speed limit. It needs to be performed when the engine is running abnormally or a certain cylinder does not work.
6.1.6 Cylinder Cut-off, Compression Test
This function can cut off a specific cylinder while the engine is running to identify if it is working improperly. Users can determine if a cylinder is normal by separately cutting it off and checking the engine's working status.
6.1.7 Clutch Learning
This function can relearn clutch values to ensure normal clutch operation. It needs to be performed after programming the TCU or replacing the gearbox or TCU.
6.2 Upgrade
This function allows you to update the diagnostic app and software. All software is updated periodically, and it is recommended to install the latest version for the best service, functions, and experience.
- Use and update of the diagnostic software pre-installed on the tool is free of charge for 2 years.
- Use and update of diagnostic software purchased in the "Mall" is free of charge for one year. If the free period is due, the user needs to renew the subscription.
Note: This function requires a stable network connection.
6.2.1 Update Diagnostic Software & App
Tap "Upgrade" on the Job menu to enter the update center. Tap "Update" to start downloading. This may take several minutes; please be patient. Once the download is finished, the software packages will be installed automatically.
6.2.2 Renew Subscription
When the free period is due, the diagnostic software of the current version will be locked. To unlock it, the user needs to renew the subscription. Tap "Upgrade" on the Job menu to enter the update center. All software that has passed the expiry date is displayed in gray. Tap to select the desired diagnostic software and then tap "Renew". Input the 24-digit PIN code of the Subscription Renewal Card (which needs to be purchased from the local dealer where you bought the tool) and then tap "Submit" to finish the renewal. The latest diagnostic software is then ready for use.
6.3 Clean Up
This option allows the user to clear cache files and free up storage space. After cleanup, the tool will reboot automatically.
7. Troubleshooting (FAQ)
Here are some frequently asked questions and answers related to this tool:
- System halts when reading data stream. What is the reason?
It may be caused by a slackened connector. Please turn this tool off, firmly connect the connector, and switch it on again.
- Screen of the tool flashes at engine ignition start.
Caused by electromagnetic disturbing, this is a normal phenomenon.
- There is no response when communicating with the on-board computer.
Please confirm the proper voltage of the power supply and check if the throttle has been closed, the transmission is in the neutral position, and the water is at the proper temperature.
- What to do if the system fails to start system scanning?
Please check the following possible reasons:
- Whether the tool is properly connected to the vehicle's DLC port.
- Whether the "Automatic detection on Connect" switch is OFF. If yes, slide it to ON.
- Why are there so many fault codes?
Usually, it's caused by poor connection or fault circuit grounding.
- How to upgrade the system?
- Switch the tool on and ensure a stable internet connection.
- Tap "Settings" on the Job Menu, select "About" -> "Version", and tap "Detect the System Version" to enter the system upgrading page.
- Follow the on-screen instructions step by step to finish the process. It may take several minutes depending on the internet speed; please be patient. After the upgrade is successfully finished, the tool will automatically restart and enter the Job menu.
8. Specifications
| Feature | Specification |
|---|---|
| Screen | 3.97-inch Touch Screen (800x480 resolution) |
| Operating System | Android 8.1 |
| Processor | 1.3GHz & 4-Core |
| RAM/ROM | 2GB/16GB |
| Battery | 3000mAh (Is Batteries Included: Yes) |
| Wireless Support | Wi-Fi (802.11b/g/n 2.4GHz) |
| Connection | WIFI, OBD Connector (Standard OBDII interface, Type-C interface) |
| OBDII Input Voltage Range | 24V |
| Product Dimensions | 9.06"L x 1.77"W x 7.8"H (212*120*34mm) |
| Item Weight | 5.19 pounds (<500G) |
| Storage Temperature | -20°C to 70°C (-4°F to 158°F) |
| Working Temperature | 0°C to 50°C (32°F to 122°F) |
| Free Update | 2 Years |
| Warranty | 5 Years |
| External Testing Certification | CE |
| Origin | Mainland China |
8.1 Accessories Checklist
For different product models, the accessories may vary. The following accessory items are for reference purposes only. For detailed accessories and parts, please consult the seller or refer to the actual package box as standard.
- Diagnostic tool x 1
- Diagnostic cable x 1
- CT 9 adapter x 1
- OBD 6-PIN adapter x 1
- Type II OBD 9-PIN adapter x 1
- User manual x 1
- Quick start guide x 1
9. User Tips
To maximize your experience with the LAUNCH CRP129 HD, consider the following tips:
- Regular Updates: Always keep your diagnostic software and APK updated to ensure the best service, functions, and compatibility with the latest vehicle models.
- Stable Network: For successful VIN detection, software updates, and remote diagnostic features, ensure a stable and solid Wi-Fi connection.
- Diagnostic Reports: Utilize the automatic diagnostic report generation feature. These reports can be saved in PDF format and easily emailed for record-keeping or sharing with clients/technicians.
- Online Feedback: If you encounter any issues during diagnosis, use the built-in feedback function. This helps the manufacturer improve the product and provides you with timely support.
- History Function: Leverage the "History" function for quick access to previously tested vehicles, allowing you to resume operations without starting from scratch.
- Maintenance Help: Explore the "Maintenance Help" section on the device for how-to videos, operation skills, and quick guides to enhance your diagnostic proficiency.
10. Warranty and Support
10.1 Warranty
The LAUNCH electronic product is warranted against defects in materials and workmanship for one year (12 months) from the date of delivery to the user. This warranty is expressly limited to persons who purchase LAUNCH products for purposes of resale or use in the ordinary course of the buyer's business.
This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions regarding use. The exclusive remedy for any automotive meter found to be defective is repair or replacement, and LAUNCH shall not be liable for any consequential or incidental damages.
Final determination of defects shall be made by LAUNCH in accordance with established procedures. No agent, employee, or representative of LAUNCH has any authority to bind LAUNCH to any affirmation, representation, or warranty concerning LAUNCH automotive meters, except as stated herein.
10.2 Customer Service
If you have any questions on the operation of the unit, please contact the seller, or contact LAUNCH Tech USA:
- Website: www.launchtechusa.com
- Phone (Service & Repair): 877-528-6249 ext: 5 (Monday - Friday 8 am - 5 pm PST)
- Public Forum: http://launch.activeboard.com
For a complete and detailed user manual, please refer to the official PDF document: LAUNCH CRP129 HD User Manual (PDF).
11. Compliance Information
11.1 FCC ID: XUJCREHD
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
11.2 RF Exposure Compliance
The device has been evaluated to meet general RF exposure requirements. The highest reported SAR for stand-alone and simultaneous transmission exposure conditions are below the maximum value. End-users must be informed of the operating requirements for satisfying RF exposure compliance.
This device is in compliance with the essential requirements and other relevant provisions of Radio Equipment Directive 2014/53/EU. The RF frequencies can be used in Europe without restriction.