1. Introduction
Thank you for choosing the ATOPCARE SW-DW Solar-Powered Mini Trail Camera. This camera is designed for various outdoor applications including wildlife monitoring, hunting, farm safety, and home security. It features solar charging, IP66 weather resistance, high-resolution imaging, and Wi-Fi connectivity for easy control via a mobile app. Please read this manual carefully before use to ensure proper operation and to keep it for future reference.

Figure 1: Trail Camera with mobile app connectivity
2. Package Contents
Please check the package to ensure all items are present:
- 1 x Trail Camera (SW-DW)
- 1 x User Manual
- 1 x Threaded Tripod
- 1 x Mounting Belt
- 1 x Type-C USB Cable

Figure 2: Included accessories
3. Camera Overview
3.1 Front View Components
- Solar Charging Panel
- Infrared LEDs
- Camera Lens
- WIFI Indicator
- PIR Sensor
- Microphone
3.2 Internal and Side View Components
- Buckle
- PIR Indicator
- Hole for A Cable Lock
- Strap Hole
- Lock Hole
- Tripod Slot
- Battery Compartment
- Menu Button
- OK Button
- Play Button
- Up/Video Button
- Down/Capture Button
- Shot Button
- LCD Screen
- RST (Reset)
- TF slot (Micro SD Card Slot)
- USB interface (Type-C)
- Switch (ON / TEST / OFF)
- DC interface (External Power Input)
- Charging indicator
4. Setup
4.1 Power Supply
The camera supports multiple power solutions:
- Main Power Supply: An integrated 18650 lithium battery (2600mAh) is charged by the camera's solar panel.
- Spare Battery Pack: The camera can also be powered by 4 x AA 1.5V batteries.
- External Power Supply: A DC 6V 1.5A power supply can be connected via the DC interface (3.5x1.35mm plug).
Important Notes on Power:
- It is recommended to fully charge the internal lithium battery via the Type-C USB port (5V 2A charger) before first use.
- When installing AA batteries, do not mix old and new batteries. Only use 1.5V AA batteries (1.2V rechargeable batteries are not supported).
- Do not connect both the USB and DC ports to power the camera simultaneously.
- The DC port does not charge the internal lithium battery.
4.2 Battery Installation
Open the camera's housing. If using AA batteries, insert 4 x AA 1.5V batteries into the battery compartment, ensuring correct polarity.
4.3 Micro SD Card Installation
The camera requires a Micro SD card (Class 10/U1, exFAT format) to store photos and videos. Ensure the camera is powered OFF before inserting or removing the Micro SD card. Insert the card into the TF slot until it clicks into place. It is recommended to format the Micro SD card using the camera's menu before first use.
4.4 Mounting the Camera
Use the provided mounting belt or threaded tripod to secure the camera. Attach the camera to a tree or other stable object at a height of 0.5-2 meters, pointing slightly downwards. Ensure the camera is facing North or South to avoid direct sunlight interference from East/West during sunrise/sunset, which can cause false triggers or overexposed images. Clear any obstructions in front of the lens or PIR sensor.
4.5 Initial Setup
After installing batteries and the SD card, switch the camera to the TEST position. This will activate the LCD screen, allowing you to configure settings. Ensure the date and time are set correctly.
Video 1: Product demonstration including physical features and initial setup steps.
5. Operating the Camera
5.1 Camera Switch Modes
- OFF: Powers off the camera.
- TEST: Activates the LCD screen for settings configuration, manual photo/video capture, and playback.
- ON: Activates monitoring mode. The camera will enter standby and begin recording based on your settings (motion detection, timing, or timelapse).
5.2 Menu Navigation and Keystrokes
Use the following buttons for navigation in TEST mode:
- MENU: Enter/exit system settings.
- OK: Confirm selection.
- Gallery: Go to the gallery to view media.
- Up/Video: Navigate up in menus or switch to video mode.
- Down/Capture: Navigate down in menus or switch to photo mode.
- Play: Play/pause videos or enter media browsing.
- Shot: Manually take a photo or start recording a video.
To reset the device, press and hold the RST button for 3 seconds.
5.3 System Settings
Access system settings via the MENU button in TEST mode. Key settings include:
- Mode Setting: Choose between Motion Detection (PIR), Timing Video, or Timelapse Video. Note: PIR is disabled if Timing or Timelapse modes are active.
- Work Time: Set specific hours for the camera to be active.
- Photo/Video Mode: Select Photo, Video, or Photo+Video.
- Photo Resolution: Options from 2MP to 24MP. Higher resolution yields better quality but larger file sizes.
- Video Resolution: Options include 720P/30fps and 1080P/30fps.
- Continuous Shooting: Set the number of photos taken per trigger.
- Recording Duration: Set video clip length (recommended 10 seconds to save battery and storage).
- PIR Sensitivity: Adjust based on ambient temperature and target size (High for distant targets in warm weather, Medium/Low for closer targets in cold weather).
- Motion Detection Filtering: Ends recording early if no further movement is detected.
- PIR Test: Allows you to test the PIR sensor's functionality.
- WiFi LED: Option to turn off the Wi-Fi indicator light.
- Loop Recording: Overwrites the oldest files when the SD card is full.
- Format SD Card: Formats the inserted Micro SD card.
- Password Protection: Set a password for camera access.
- Factory Reset: Restores all settings to default.
5.4 Wi-Fi and Mobile App Connection
The camera can be controlled via the