1. Introduction
This manual provides essential information for the safe and effective installation, operation, and maintenance of your Bartoo Blow Off Valve (BOV) Diverter, model RS-BOV058-Black (T9352). This product is designed as a performance upgrade for specific Mini Cooper, Citroen, and Peugeot Turbo models.
For a detailed user manual in PDF format, please refer to the official document: User manual (PDF).
2. Safety & Warnings
Important Safety Information: Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Warning: This is an automotive turbo system performance component, not a toy. Keep away from children and pets at all times.
- Professional installation by a certified automotive turbo technician is strongly recommended. Improper fitting, incorrect spring tension setup, or unprofessional installation may lead to catastrophic turbo failure, engine damage, loss of vehicle control, especially at high boost or high speeds, resulting in serious injury or death.
- Use only for the specified Mini Cooper N14 1.6L / Citroen / Peugeot Turbo models; do not apply to non-specified vehicles, non-turbo equipped cars, or uncertified modified turbo setups.
- Always use proper vehicle lifting equipment and secure the vehicle on a flat, solid surface before any work.
- Wear safety glasses, cut-resistant gloves, and protective footwear to avoid injury from sharp metal edges or high-pressure turbo components.
- Do not install if the BOV body, spring assembly, O-ring seal, or hardware is cracked, deformed, damaged, worn, or contaminated. Discard defective components immediately and do not use.
- After installation, perform a thorough boost pressure test and pre-drive inspection of all turbo connections. Then, test drive at low speed to confirm stability, throttle response, and no abnormal whistling/leaking before normal driving.
- This product is a performance upgrade that alters vehicle turbo operation. Ensure compliance with local vehicle emission and road regulations before use, as modification may void factory vehicle warranty.
3. Product Information
The Bartoo Blow Off Valve (BOV) Diverter Kit (part number T9352) is designed for Mini Cooper N14 1.6L, Citroen, and Peugeot Turbo models. It replaces factory stock turbo diverter valves to reduce turbo lag, improve throttle response, and protect turbo components from pressure damage. It is a non-electrical, non-toy automotive turbo system performance component.
Crafted from high-quality anodized aluminum alloy body, precision spring assembly, and durable stainless steel hardware, it is free from restricted hazardous substances and meets automotive aftermarket performance and safety standards.
Key Features:
- Sharper throttle response.
- Faster boost recovery on gearshift.
- Solves boost leaking issues.
- Built to last.
- More responsive, less expensive, easier to install, and doesn’t cause compressor surge/turbo flutter.
Package Contents:
The kit includes one (1) Blow Off Valve and all necessary accessories for installation as shown in the image below.
4. Application / Compatibility
This Blow Off Valve Diverter is compatible with the following vehicle models (N14 Engine only where specified):
- Citroen:
- C4 1.6 THP 155 B7 115kw Petrol Engine FWD Hatchback 11/09-on
- DS3 1.6 THP 155/200 115kw Petrol Engine FWD Hatchback 04/10-07/15
- DS4 1.6 THP 155/200 115kw Petrol Engine FWD Hatchback 04/11-07/15
- DS4 1.6 THP 155/200 147kw Petrol Engine FWD Hatchback 04/11-07/15
- DS4 1.6 THP 155/200 120kw Petrol Engine FWD Hatchback 04/12-07/15
- DS5 1.6 THP 155/200 115kw Petrol Engine FWD Hatchback 11/11-07/15
- MINI:
- Cooper S R56 N14 Engine only R56 128kw Petrol Engine FWD Hatchback 10/06-02/10
- John Cooper Works R56 N14 Engine only R56 155kw Petrol Engine FWD Hatchback 11/07-11/13
- Cooper S R57 N14 Engine only R57 128kw Petrol Engine FWD Convertible 04/08-07/10
- John Cooper Works R57 N14 Engine only R57 155kw Petrol Engine FWD Convertible 08/08-05/15
- Clubman Cooper S R55 N14 Engine only R55 128kw Petrol Engine FWD Wagon 10/07-06/14
- Clubman John Cooper Works R55 N14 Engine only R55 155kw Petrol Engine FWD Wagon 11/07-12/14
- Peugeot:
- 207 1.6 16V RC WA_, WC_ 110kw Petrol Engine FWD Hatchback 02/06-on
- 207 1.6 16V RC WA_, WC_ 128kw Petrol Engine FWD Hatchback 02/07-on
- 207 CC 1.6 16V WD_ 110kw Petrol Engine FWD Convertible 02/07-on
- 3008 1.6 THP T8 115kw Petrol Engine FWD MPV 06/09-08/16
- 508 1.6 THP 8D_ 115kw Petrol Engine FWD Sedan 11/10-on
- 208 GTI T8 147kw Petrol Engine FWD Hatchback 08/12-on
- 208 GTI A9 115kw Petrol Engine FWD Hatchback 03/12-on
- 308 1.6 THP T7 110kw Petrol Engine FWD Convertible 06/09-on
- 308 1.6 THP T7 103kw Petrol Engine FWD Convertible 06/09-on
- 308 1.6 THP T7 110kw Petrol Engine FWD Hatchback 09/07-on
- 308 1.6 THP T7 115kw Petrol Engine FWD Hatchback 10/09-on
- 308 1.6 THP T7 128kw Petrol Engine FWD Hatchback 03/08-on
- 308 1.6 THP 151kw Petrol Engine FWD Hatchback 06/14-on
- 308 1.6 THP T7 110kw Petrol Engine FWD Wagon 09/07-on
- 308 1.6 THP T7 115kw Petrol Engine FWD Convertible 06/09-on
- RCZ THP156 2010-on 115kw Petrol Engine FWD Coupe 03/10-12/14
5. Setup & Installation
5.1 Before First Use:
- Confirm the kit fits your specific Mini Cooper N14 1.6L / Citroen / Peugeot Turbo model.
- Inspect all components for cracks, deformation, or damage. Discard any defective parts immediately.
5.2 Installation Steps:
- Follow your vehicle's service manual for specific procedures related to turbo diverter valve replacement.
- Safely lift and support the vehicle using appropriate equipment on a flat, solid surface.
- Remove the factory turbo diverter valve.
- Clean all mounting surfaces thoroughly to ensure a proper seal.
- Install the new Bartoo BOV kit, securing it with the included hardware.
- Adjust the spring tension according to factory boost specifications for your vehicle.
- Perform a boost leak test to verify the integrity of the installation.
Note: Do not attempt installation without professional turbo system experience.
6. Operating Instructions
The Bartoo Blow Off Valve (BOV) Diverter operates automatically in conjunction with your vehicle's turbocharger system. Its primary function is to release excess boost pressure when the throttle closes, preventing compressor surge and improving turbocharger longevity and performance.
Post-Installation Operation Check:
- After installation, perform a thorough boost pressure test.
- Conduct a pre-drive inspection of all turbo connections.
- Test drive the vehicle at low speed to confirm stability, proper throttle response, and the absence of abnormal whistling or leaking sounds before resuming normal driving.
7. Maintenance
Regular inspection and maintenance are crucial for the longevity and optimal performance of your BOV diverter.
Maintenance Schedule:
- Regularly inspect the kit for leaks, looseness, wear, or damage.
- If any issues are found (e.g., cracks, deformation, damage to the BOV body, spring assembly, O-ring seal, or hardware), replace the affected components immediately.
- Store any unused or spare kits in a dry, cool place, away from impact, moisture, and children.
8. Troubleshooting
If you experience issues after installing the Bartoo BOV Diverter, consider the following common troubleshooting steps:
| Symptom | Possible Cause | Solution |
|---|---|---|
| Reduced engine performance / Boost leak | Improper installation, loose connections, damaged O-rings, incorrect spring tension. | Re-check all connections for tightness. Inspect O-rings and seals for damage. Verify spring tension is set to factory specifications. Perform a boost leak test. |
| Abnormal whistling or hissing sounds | Air leak from BOV or associated piping. | Inspect BOV and all vacuum/boost lines for leaks. Ensure all clamps are secure. |
| Turbo flutter / Compressor surge | Incorrect spring tension, BOV not opening/closing correctly. | Adjust spring tension. Inspect BOV piston for smooth operation and ensure no obstructions. |
If issues persist after attempting these steps, it is recommended to consult a certified automotive turbo technician.
9. Specifications
| Attribute | Value |
|---|---|
| Product Name | Blow Off Valve Diverter |
| Model Number | RS-BOV058-Black |
| OEM NO. | T9352 |
| Material | Aluminum |
| Color | Black |
| High-concerned chemical | None |
| Origin | Mainland China |
| Package Weight | 0.25 kg |
| Package Dimensions (L x W x H) | 17 cm x 10 cm x 4 cm |
Product Dimensions:
- Outer Diameter (top): 2.44" (62mm)
- Outer Diameter (bottom): 2.52" (64mm)
- Height: 2.01" (51mm)
- Inlet Diameter: 0.94" (24mm)
- Outlet Diameter: 0.43" (11mm)
- Mounting Hole Diameter: Φ0.23" (6mm)
10. User Tips
- Always ensure your engine is cool before attempting any installation or inspection of turbo components.
- Use a torque wrench to tighten fasteners to the manufacturer's specified values to prevent over-tightening or under-tightening.
- Keep all removed factory parts in case you need to revert to stock or for future reference.
- Consider periodic cleaning of the BOV to ensure smooth piston movement and prevent carbon buildup.
11. Frequently Asked Questions (FAQ)
- Q: What is the primary benefit of installing this BOV diverter?
- A: It helps reduce turbo lag, improves throttle response, and protects the turbocharger by releasing excess boost pressure, preventing compressor surge.
- Q: Is professional installation required?
- A: Professional installation by a certified automotive turbo technician is strongly recommended due to the complexity and critical nature of turbo system components.
- Q: Will this product affect my vehicle's warranty?
- A: As a performance upgrade, installing this product may void your factory vehicle warranty. Please check with your vehicle manufacturer or dealership.
- Q: How often should I inspect the BOV?
- A: It is recommended to regularly inspect the kit for any signs of leaks, looseness, wear, or damage, and replace components as necessary.
12. Warranty & Support
For any questions regarding product warranty, technical support, or replacement parts, please contact the seller directly through the platform where the product was purchased. Ensure you have your purchase details and product model information available when contacting support.