MOES Tuya Smart Zigbee Roller Blinds Motor Shade User Manual

1. Introduction

Thank you for choosing the MOES Tuya Smart Zigbee Roller Blinds Motor Shade. This manual provides essential information for the safe installation, operation, and maintenance of your device. Please read it thoroughly before use and keep it for future reference.

Important Notice:

This motor is hardwired only and requires a constant power supply. It does not contain a built-in battery, it is not rechargeable, and it cannot be powered by batteries. Please make sure a proper hardwired connection is available before purchasing.

Image: Important notice about the hardwired nature of the motor.

Image: MOES Zigbee Smart Roller Blinds Motor, highlighting app remote control, voice control, and percentage control, compatible with Moes App, Smart Life, Tuya, Alexa, and Google Assistant.

2. Package Contents

Ensure all items are present and in good condition upon unpacking:

• Curtain motor x1
• Crown x1
• Wheel x1
• Instruction manual x1

3. Specifications

The MOES Smart Zigbee Roller Blinds Motor is designed for 38mm tubes and offers two torque versions. Refer to the table below for detailed specifications:

Table: Comparison of data for 1.1N.m and 2N.m motor versions.

Image: Visual representation of the comparison table for motor specifications.

Image: Detailed dimensions of the motor (410mm length, 38mm diameter) and mounting brackets.

Image: Product details showing the 'Set button' and indicating suitability for a 38mm tube.

4. Setup and Installation

4.1. Wiring Solution

The motor requires a hardwired connection. Ensure power is off before proceeding with wiring.

110V/220V Power Wiring:

• Blue: Null wire
• Brown: Live wire
• Black: L2
• White: L1
• Yellow and Green: Earth

Dry Contact Wire Connection:

• Yellow: Public line
• Red: Up phase line
• Black: Down phase line

230V/50Hz Wiring:

• Blue: Null wire
• Brown: Live wire
• White: Connected to down switch
• Black: Connected to switch common line
• Grey: Connected to up switch
• Yellow and Green: Earth line

4.2. Physical Installation Guide

Follow these four steps for physical installation. For further assistance, contact customer service.

1. Position the motor according to the diagram markings, ensuring the drive shaft groove aligns precisely with the roller channel before insertion.
2. Insert the crown into the motor's bottom port, verify its alignment with the roller end position, then push and lock until fully secured.
3. Install the end plug into the motor's left-side port: align with the designated groove and fasten it firmly.
4. Mount the motor-roller assembly to the target location (Note: Positioning varies depending on installation scenarios).

Image: Step-by-step visual guide for installing the motor into the roller blind tube and mounting it.

4.3. App Connection and Pairing

A Zigbee gateway is required to connect the motor to the Tuya App or Smart Life App. Please purchase the gateway separately if you do not already have one.

Image: Diagram showing the connection flow: Motor -> Zigbee Gateway -> WiFi Router -> Smartphone App / Voice Control.

Download the App:

Scan the QR code below to download the Tuya App or Smart Life App.

Image: QR codes for downloading the Tuya App and Smart Life App.

Connect the Motor to the Tuya App & Smart Life App:

The 'beep' and 'hint' refer to motor indicators. Proceed to the next step only after the prompts are completed.

Method 1 (Power Cycle):

1. Switch off power.
2. Switch on power.
3. Wait for beep x1, hint x1.
4. Repeat steps 1-3 four more times (total 5 power cycles).
5. After the fifth power cycle, wait for beep x1, hint x1, then OK.

Note: Code matching should be completed within 10 seconds of power-on.

Method 2 (Set Button):

1. Press the P1 button (set button) on the motor 25 times.
2. Wait for beep x1, hint x1.
3. Press P2 once.
4. Press UP once.
5. Press P2 once.
6. Press UP once.
7. Wait for beep x1, hint x1, then OK.

After successful pairing, the motor will be discoverable in the app.

Video: Demonstration of wiring, pairing the motor with the app via a gateway, and basic app control.

5. Operating Instructions

5.1. App Remote Control

Control your roller blinds from anywhere using the Tuya or Smart Life app on your smartphone. You can open, close, or stop the blinds at any desired position.

Image: App interface showing controls for opening, stopping, and closing blinds, with a percentage indicator.

5.2. Voice Control

Integrate with Amazon Alexa or Google Home for convenient voice commands. Simply say "Alexa, open the curtains" or "OK Google, close the blinds" to control your shades.

Image: Demonstration of voice control using Amazon Alexa and Google Home devices to operate the blinds.

5.3. Timing Function

Set schedules for your blinds to open or close automatically at specific times, enhancing convenience and energy efficiency.

Image: Examples of setting timing functions, such as opening blinds at 7:00 AM and closing at 6:30 PM.

5.4. RF Remote Control (Optional)

If you have purchased the RF remote control, you can operate the blinds directly without the app or voice commands. The remote typically includes buttons for Rise, Stop, Descend, and Channel setting.

Image: An RF remote control with buttons for up, down, stop, and channel selection.

5.5. Percentage Control

Adjust your blinds to a specific percentage of open or closed, allowing for precise light and privacy management.

Image: App interface demonstrating setting blinds to 50% open/closed.

5.6. Smart Scene Linkage

Integrate your roller blinds motor into smart home scenes. For example, link it with smart lighting to automatically adjust both when you activate a 'movie night' scene.

Image: An example of a smart scene where the Zigbee Motor and a Smart Bulb are linked.

5.7. Motor Rotation Switchable

If the motor's direction of operation is incorrect after installation, you can reverse it either by adjusting the wiring or through the MOES App settings.

Image: Diagram illustrating how to correct the motor's rotation direction if wired incorrectly, or by reversing it via the app.

5.8. Programming and Limit Settings

The motor allows for precise programming of upper and lower limits, as well as fine-tuning of positions. These settings ensure the blinds stop exactly where desired.

Limit Setting:

To enter limit setting mode: Press P2 once, then UP once. Run to the desired location, press STOP once. This sets the upper limit. For the lower limit, press DOWN once, run to the required location, then press STOP once. To complete, short press P2 five times or long press for 3 seconds.

Note: After setting the upper and lower limits, the limit setting is complete.

Limit Position Fine-Adjustment:

If the curtain has reached its upper or lower limit position, you can enter fine-adjustment mode. Press UP or DOWN to run to the desired spot. To complete, short press P2 five times or long press for 3 seconds.

Note: If the initial limit is not ideal and fine adjustment is required, use this function.

The Third Limit Setting:

This can only be set after the upper and lower limits have been completed. Run to the desired location, press P2 once, then STOP once. Repeat this operation to delete the third limit setting.

Delete All Limits:

Press P2 once, then DOWN once, then P2 once. This will delete all limits.

Delete an Emitter:

Press P2 once, then P2 once, then P2 once. This will delete an emitter.

Deadman Setting:

The factory default is jog mode. Repeated operations can switch modes.

Change Direction:

If pressing the up button on the transmitter causes the motor to run downwards, please take action to correct it (refer to Motor Rotation Switchable section).

Restore Factory Setting:

Long press P1 until beep x2, then OK.

Motor Speed Regulation:

Long press P2 for 2 seconds to increase motor speed ('speed is up') or decrease motor speed ('speed is down').

6. Maintenance

To ensure optimal performance and longevity of your MOES Smart Zigbee Roller Blinds Motor, follow these general maintenance guidelines:

• Keep the motor and surrounding area clean and free from dust and debris.
• Avoid exposing the motor to excessive moisture or extreme temperatures.
• Regularly check the wiring connections to ensure they are secure.
• Do not attempt to disassemble or repair the motor yourself. Contact qualified personnel for any repairs.

7. Troubleshooting

If you encounter issues with your roller blinds motor, try the following steps:

• Motor not responding: Check power supply and wiring connections. Ensure the Zigbee gateway is powered on and connected to your network. Verify the motor is properly paired with the app.
• Incorrect direction of movement: Refer to the "Motor Rotation Switchable" section (5.7) to correct the direction via wiring or app settings.
• Blinds not stopping at desired position: Re-calibrate the limit settings as described in the "Programming and Limit Settings" section (5.8).
• Remote control not working: If using an RF remote, ensure it is paired correctly with the motor (refer to the PDF manual for specific RF remote pairing instructions if different from app pairing). Check remote battery if applicable.
• App connectivity issues: Ensure your Zigbee gateway is online and your smartphone has a stable internet connection. Restart the app and the gateway if necessary.

8. User Tips

• For optimal smart home integration, ensure your Zigbee gateway is centrally located within your home to maintain a strong signal with the motor.
• When setting up timing functions, consider natural light cycles and your daily routine for maximum convenience and energy saving.
• If using multiple motors, label them clearly in the app for easy identification and control.

9. Warranty and Support

For detailed warranty information, technical support, or further assistance, please refer to the complete user manual PDF or contact MOES customer service.

A comprehensive user manual is available in PDF format for download:

View User Manual (PDF)