Introduction
The Xiaomi Mijia Electric Grinding Pen is a versatile tool designed for fine grinding, carving, polishing, burnishing, and drilling tasks. It features a powerful brushless motor, stepless speed control, and a portable design, making it suitable for various creative and DIY projects.
This manual provides detailed instructions for the safe and effective use, maintenance, and troubleshooting of your electric grinding pen.
Parts Description
Familiarize yourself with the components of your Xiaomi Mijia Electric Grinding Pen:
- Collet: Holds rotary bits, featuring a tool-free hand-twist design.
- Power Button: Long press to turn on; short press to turn off. Long press for emergency shut-off.
- Rear Speed Dial: Turn clockwise to speed up, counterclockwise to slow down. Provides stepless speed control.
- Indicator Light:
- Solid on: Indicates the device is working or charging.
- Red flashing: Indicates low battery.
- Green solid: Indicates the device is fully charged.
- Type-C Port: Used for charging and external power input.
Setup: Bit Installation & Removal
The grinding pen uses a 2.35 mm universal shank for its bits.
Installation:
- Hold the collet lock ring.
- Twist the collet cap counterclockwise to loosen it.
- Insert a 2.35 mm shank bit all the way into the collet.
- Twist the cap clockwise to tighten. Ensure the bit is stable and not wobbling before use.
Removal:
To remove a bit, reverse the installation steps.
Operating Instructions
Power On / Off
- To Turn On: Long press the power button for 1 second.
- To Turn Off: Short press the power button.
- Emergency Shut-off: Long press the power button if an emergency shut-off is needed.
Speed Adjustment
Rotate the rear speed dial to adjust the speed steplessly between 15000-22000 rpm. Turn clockwise to increase speed, and counterclockwise to decrease speed.
Two Working Modes
- Battery Mode: Use cordless for portable, outdoor applications.
- Plug-in Mode: Connect to a 5V/3A charger or power bank for continuous use. Charging is disabled during operation in this mode.
Charging
- Charge the device only when it is off.
- Connect the Type-C cable to the pen; charging starts automatically.
- Disconnect the cable when the indicator light turns green, signifying a full charge.
Maintenance & Storage
- Battery Care: Fully charge the device before long-term storage. Recharge every 3 months to extend battery life.
- Cleaning: Do not wash the body with water. Clean dust from the collet regularly with a brush to prevent jamming.
- Storage: Store the pen in a dry, cool place, ideally between -10°C and 45°C.
Troubleshooting
Device Will Not Start:
- Check the battery level.
- Ensure the bit is properly installed.
- Long press the power button again to attempt to turn on.
Unstable Speed / Vibration:
- Reinstall the bit to avoid eccentricity.
- Clean any dust from the collet.
- Adjust the speed dial properly.
Charging Abnormality:
- Try using another charger and cable.
- Ensure the device is off when charging.
- Check the Type-C port for any damage or looseness.
Specifications
| Feature | Detail |
|---|---|
| Model | MJDMB001QW |
| Dimensions | Approx. 184 x 20 x 20.6 mm |
| Net Weight | Approx. 310 g |
| Motor | Brushless coreless motor |
| No-load Speed | 15000-22000 rpm (stepless speed control) |
| Battery | 800mAh / 3.7V Lithium battery |
| Working Time | Up to 60 minutes per full charge |
| Charging Input | Type-C, 5V/1A |
| Charging Time | About 90 minutes for a full charge |
| Power Supply Modes | Battery mode / Plug-in direct drive |
| Collet Size | 2.35 mm universal shank |
| Wireless Communication | Non-Remote Function |
| Power Source | Other (Battery/Plug-in) |
| Battery Included | Yes |
| Inbox Adaptor | No |
| Origin | Mainland China |
Included Bits (16 pieces)
The Xiaomi Mijia Electric Grinding Pen comes with a set of 16 high-quality accessories for various applications:
- 6 x Abrasive bits: For engraving and fine grinding of jade, metal, and glass.
- 4 x Grinding wheel bits: For rough grinding and deburring of metal and plastic.
- 2 x Rubber bits: For fine grinding and rust removal.
- 2 x Wool bits: For mirror polishing of metal, jade, and wood.
- 1 x Twist drill: For drilling wood, plastic, and other soft materials.
- 1 x Wool brush: For dust cleaning and surface preparation.
Safety Precautions
- Always wear safety goggles and a dust mask during use to protect your eyes and respiratory system.
- Keep the device out of reach of children.
- Keep hair, loose clothing, and flammable materials away from the rotating parts of the tool.
- Stop immediately if the bit becomes loose or if you hear any abnormal noise during operation.
- Avoid running the tool at high speed without a load for extended periods.
- The operating temperature range is 0-40°C.
- Do not wash the main body of the device with water. Clean dust with a brush.
User Tips
No specific user tips were available from reviews or Q&A at this time. Always refer to the main instructions for optimal use.
Warranty
This product is covered by an official Xiaomi after-sales warranty. Normal warranty service applies to non-artificial quality defects with valid proof of purchase.
Support
For further details or a printable version of this manual, you may refer to the official user manual PDF. The package and user manual provided with the product are in Chinese.
For additional support, please contact Xiaomi customer service or visit their official website.