PowMr BEN24-N/BEN48-N

Contents

PowMr 24V/48V Battery Equalizer User Manual

Models: BEN24-N, BEN48-N

1. Introduction

The PowMr Battery Equalizer is designed to maintain voltage balance in series-connected battery packs during both charging and discharging cycles. It is crucial for systems where two or more batteries are connected in series, as individual battery cells can develop voltage differences due to variations in chemical composition, temperature, and self-discharge rates. These discrepancies can lead to battery imbalance, where some cells become overcharged while others remain undercharged, ultimately shortening the overall battery lifespan.

This equalizer utilizes energy transfer balancing technology to bidirectionally compensate battery voltages. It automatically activates when the voltage difference between two cells reaches 10mV, transferring current from the higher-voltage battery to the lower-voltage battery until equilibrium is achieved. It can remain continuously connected to your battery system 24/7, automatically maintaining energy balance without manual intervention.

The equalizer is suitable for various battery types, including Lead-Acid (VRLA, Gel, Flood, AGM), Lithium Iron Phosphate (LFP), Nickel-Cadmium (Ni/CD), and Nickel-Metal Hydride (Ni/MH) rechargeable batteries. It activates when the voltage exceeds 2.4V, making it applicable for single-cell voltage ranges from 2.4V to 12V.

A detailed user manual (PDF) is available for download here.

2. Product Features

Diagram illustrating key features of the battery equalizer

The PowMr Battery Equalizer offers several benefits:

  • Extend Battery Life: By maintaining voltage balance, it prevents overcharging and undercharging, significantly prolonging the service life of your battery bank.
  • Reduce Battery Replacement: Balanced batteries perform better and last longer, reducing the frequency and cost of battery replacements.
  • Balance Charge & Discharge: Ensures all batteries in a series are charged and discharged uniformly.
  • Save Extra Expense: Contributes to overall system efficiency and reduces maintenance costs.
  • Insulation Component: Designed with safety in mind.
  • Seal Housing Design: Provides protection for internal components.

3. Setup and Installation

Before installation, ensure all batteries are connected in series according to your system's voltage requirements (e.g., two 12V batteries for a 24V system, four 12V batteries for a 48V system).

3.1 Wiring Instructions

  1. Red Cable: Connect to the positive (+) pole of the battery.
  2. Black Cable: Connect to the negative (-) pole of the battery.
  3. White Cable: Connects to the middle connection point between two batteries in series. This can be either the negative pole of Battery B or the positive pole of Battery A (the common connection point).

Important Safety Note: Do not connect both the red and black wires to the same battery to avoid a short circuit. The white wire can be connected to any battery without causing a short circuit, but it is intended for the midpoint connection.

3.2 Wiring Diagrams

The following diagrams illustrate common wiring configurations:

Wiring diagram for a 24V battery bank using two 12V batteries and a BE24-N equalizer.
Figure 1: 24V Battery Bank (2 x 12V Batteries)
Wiring diagram for a 24V battery bank using four 12V batteries and a BE24-N equalizer.
Figure 2: 24V Battery Bank (4 x 12V Batteries)
Wiring diagram for a 36V battery bank using three 12V batteries and two BE24-N equalizers.
Figure 3: 36V Battery Bank (3 x 12V Batteries)
Wiring diagram for a 48V battery bank using four 12V batteries and three BE24-N equalizers.
Figure 4: 48V Battery Bank (4 x 12V Batteries)
Comprehensive wiring diagrams for 24V, 36V, and 48V battery packs, showing multiple equalizers for higher voltage systems.
Figure 5: Multiple Equalizer Wiring for 24V, 36V, and 48V Systems

3.3 Installation Video

Video: This video demonstrates the installation process for a 24V battery setup using two 12V batteries and the BE24-N equalizer, including connecting the black, white, and red wires to the battery terminals.

4. Operating Instructions and LED Indicators

After successful wiring, the equalizer will automatically begin balancing the batteries. The display panel features LED indicators to show the balancing status and any voltage warnings.

Close-up of PowMr BE24-N Battery Equalizer with LED indicators and connection points.
Figure 6: BE24-N Interface Description

4.1 Interface Description

  • Balanced Working State Area (LEDs A & B):
    • A: Indicates high voltage group.
    • B: Indicates low voltage group.
  • Under Voltage Warning Area (LEDs A & B):
    • A: Represents under-voltage of the high voltage area.
    • B: Represents under-voltage of the low voltage area.
  • LED Power Indicator: Shows the power status.
  • Le Switch: (Function not detailed in provided data, typically for light or mode selection).

4.2 Indicator Behavior

LED indicator states for battery voltage differences (below 10V and above 10V).
Figure 7: LED Indicator States
  • Blinking Green Light (Set 1): Indicates lower voltage in the respective battery. For example, if 'A' blinks green, Battery A has lower voltage.
  • Solid Red Light (Set 2): Displays for voltage below 10V in the respective battery. For example, if 'B' shows a solid red light, Battery B has voltage below 10V.
  • No Blinking (Both A and B indicators): If neither A nor B indicators blink, it means the battery voltage difference is below 80mV. This signifies that the batteries are balanced, and the equalizer will deactivate until a voltage difference of 10mV or more is detected again.
Visual comparison of battery voltages before and after using the equalizer, showing balanced voltages.
Figure 8: Voltage Balancing Effect

5. Maintenance

  • Regularly inspect all cable connections to ensure they are secure and free from corrosion.
  • Keep the equalizer clean and free from dust and moisture.
  • Monitor the LED indicators periodically to ensure proper operation and battery health.
  • Ensure adequate ventilation around the battery bank and equalizer.

6. Troubleshooting

  • Indicators not lighting up: Check all connections to the batteries and ensure the batteries have sufficient voltage (above 2.4V per cell).
  • Persistent voltage imbalance (indicators always blinking): While the equalizer works continuously, if a significant imbalance persists over an extended period, it may indicate a severely degraded battery or an issue with the wiring. Verify battery health and connections.
  • Can this equalizer connect two 48V batteries? No, this product is designed to perform equalization for 12V batteries connected in series to form 24V or 48V systems. It does not directly balance two 48V batteries.

7. Specifications

ModelBE24-NBE48-N
Battery nominal voltage2*12V4*(2.4V/3.6V/6V/9V/12V)
Optimizing current0-5A0-10A
Quiescent current<3mA5mA(12V) 1.2mA(2.4V)
Dimensions78*78*28mm69*129*28 mm
ProtectionReverse polarity protectionReverse polarity protection
Low Voltage Disconnect10V1.8V

8. User Tips

  • Ensure all battery terminals are clean and free of corrosion for optimal connection and performance.
  • Always double-check wiring polarity before powering on the system to prevent damage to the equalizer and batteries.
  • For systems requiring multiple equalizers (e.g., 36V or 48V systems), ensure each equalizer is correctly connected to its designated pair of 12V batteries.

9. Warranty and Support

This product comes with a 1-year warranty.

For technical support or inquiries, please contact:

SHENZHEN HEHEJIN INDUSTRIAL CO., LTD
Address: Room E, 10th Floor, Building A, Rongde International, Henggang Street, Longgang District, Shenzhen, Guangdong, China 518116
Tel/Fax: +86 755-28219903
Web: https://powmr.com
E-mail: support@powmr.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.